Does the 2002 7.3 have an automatic high idle in cold weather?When you start it after it runs for a few moments it goes into high idle until you hit the accelerator. I had a 96 powerstroke before this one,it didn't do this. Just wondering?
View 4 RepliesSo finally got my truck running due to a fuel issue. Anyways been driving it for a week or two now, and I have a strange problem idk if it has been covered here or not.
Driving around tow etc if you come to a light or whatever and stop the rpms stay at 800rpm. Now if you shift it out of gear and back into drive the rpms settle back down around 650. Where is should be.
My guess is the torque converter is not disengaged all the way when it stuck at high rpm (800-900) for this situation. No cel, slippage, or crazy noises
2002 7.3 power stroke all stock right now @160k black crewcab
Previous owner had a tunner on it but not anymore. Could it have smoke the trans???
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesI have the LED mod and several weeks ago, my LED stopped indicating and the truck would not start in cold weather unless I jumped the terminal on the relay. I replaced the relay and while I was tightening one of the small lugs, the one towards the nose of the truck, I felt it break.
The truck acted just like it had been for the weeks prior, if I didn't jump the relay, it wouldn't cold start, so I assumed, because I had broken that small lug, it wasn't getting the signal to turn them on.
So what now? obviously the GP's themselves are working, as the truck starts when I jump them. But for some reason no signal is getting to the relay. What do I need to check to see what is going on between the PCM and the relay?
I have a 99 f350 and I can't get my truck to kick up the idle when it's cold out. There have been mornings in the negatives and still nothing. I replaced my egr tube and cleaned the exhaust pressure sensor. My exhaust back pressure valve opens and shuts while driving at slow speeds but not while at idle, but I don't know if that's related. I replaced the oil temp sensor with a ford motorcraft one. And I plugged my intake air temperature sensor into a buddy's truck with the same motor and his truck still idled up no problem.
View 14 RepliesWe're currently RV camping in the Wyoming Wind River Range at 8500 ft and is getting to freezing at night. The past two mornings the truck has been very difficult to start and I got quite a bit of smoke. This morning it took two or three tries but I got it going.
View 3 RepliesHere's the deal. 99 Powerstroke out new injectors and orings. Did orings twice to make sure i didn't damage it. New turbo, new utvc gasket, new ipr, new fuel pump, I new complete engine wire harness. I pulled the injectors and ran in another truck no problem. New injector cups compression was all in the 300-375 range. Any cold start smokes like hell. Goes away when driving after the first time of hitting boost. Spits and shudders for a few seconds until boosting. Every time I stop it starts smoking again at idle. No power loss not using oil. Can't get a grasp on this smoking issue. When cold start I kill millions of mosquitos in a one-mile radius.
View 3 RepliesI have noticed thru the cold months after I start my 2001 F250 7.3L 4X4 after it sits about a minute "warming up" that it goes into a high idle. The high idle will stop once I press the brakes. Is this normal?
I think this is a unrelated issue, but just started over the weekend. Was riding home, and pressed my brakes and the pedal moved almost to the floor. Not normal conditions for my truck. Usually the pedal is very stiff. I have noticed that my power steering pump has had a hum for months. I changed the fluid (ATF Mercon) within the last 6k miles and that calmed it down a bit.
After the pedal went to the floor, the hum seemed to quieten down even more. The power steering still works and the reservoir has adequate fluid and so does the brake fluid reservoir. I haven't noticed any leaks around the truck. I'm going to bleed the brake in an hour or so. The brakes pedal seems stiff when I press it after the high idle, but then it gets soft after a pump or two.
My truck was shuddering in od. So as I last effort thinking it might be injectors I pulled all of them and replaced all of the orings and valve cover harnesses. After all of this was done seemed to do nothing at all. Now a new problem has surfaced. It's having idle problems. It will now idle at 780-850 instead of 650-700rmps. Also on deceleration it will miss pretty bad. Checked all of my injectors again all connections are good and all of the injectors are tight. Not burning any oil. So I unplugged the icp and bam runs like a top perfect running engine. So I bought a new one and plugged it in and itake doing the same thing. So what is going on! Also it was throwing a random check engine light but wouldn't bring a code up I'm completely lost....
View 2 RepliesI have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
I just did an engine swap and have an odd noise that I was curious on where to start. It sounds like a buzz test on an injector at 2,250 rpm and gets louder as rpms increase but starts out very faint and get louder. Makes noise converter unlocked and locked in gear under load and free rev no load.
-2002 F550
-Fuel pressure is 60+ psi all the time
-Regulated return fuel system
-New injectors all AD
-Stock tune
-38R turbo
-New flexplate
-injector hold down tight
-new degas res
-new water pump.....
Ok, so my '02 has dual alt from factory and lately I have noticed a "growl" only at idle. Upon further diagnosis it is coming from the belt. So I replaced the tensioner, upper idler, and belt seeing as how they didn't look in good shape. Still there. I noticed from looking under the truck where the belt comes off the crank to the lower idler there is a lot (2" or so) belt *flutter* (slap/slop) but as soon as you give it any fuel it smooths out and the noise goes away. Let it idle and the noise comes back with the belt slap/flutter. For those with dual alternators, look at your belt from under the truck and see if yours is smooth at idle. Now I do notice it doesn't make the noise for the first few minutes of running. Next I am going to try bypassing the lower alternator and lower idler to try and pinpoint the prob.
View 14 RepliesTruck (02' , 7.3 ) has check engine light and since I'm on vacation don't have access to my Autoenginuity diagnostic software, so looks like I'll have to go a auto parts outlet to get the code read.
But.... before I do I wanted to get some input from y'all. Basically what happens is the idle goes up while in gear and when I put it in neutral, idle goes back down to normal. In addition I noticed (yesterday) somewhat of a lope or stumble at idle while in gear. No stalling and no effect to fuel mileage.
Since I'm away and away from my tools I'm somewhat limited. Certainly once I get the code I'll know more.
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 RepliesI have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
What causes elevated engine idle when cold or initial startup? Asking another way, what would cause it not to have the elevated idle on start up?
View 14 RepliesI have a 2002 f350 that has had cold starting issues since I bought it. I have replaced the glow plugs twice, the glow plug solenoid four times. When I put a new solenoid on it it works fine for a short time. I know the solenoids are bad because I get battery voltage on one side and nothing on the other. If I jump the solenoid with a jumper wire I can get the truck to start. I thought I was getting bad solenoids but I have recently tested the activation circuit and am getting constant power there. I.e. It never shuts off. I think this is what is causing the solenoids to burn up. From the tracing of wiring diagrams I have done, the only thing before the solenoid is the Pcm. So now to the question,
1) What controls the activation of the Glow plugs? Is there a temperature sensor or something before the Pcm.
2) Is this a case of my Pcm going out on me? I am a mechanic in the army so I have a decent understanding of mechanics.
However I am at a loss for these systems.
Got a 2002 7.3 F-350 with 300,000 miles and for the last couple of years I've been getting blue smoke on cold morning start ups and its been gradually getting worse, it clears up after about 30 seconds and all is normal,No loss of performance, Oil consumption is minor, however I hate a vehicle that blue smokes, I'm guessing my issue is valve seals are worn, I was wondering if it is possible to replace the seals while the heads are on the engine? and was also wondering how much time it would take to fix? as i would have to have it professionally done. I know its hard to guess a time frame and everyone is different. Sounds like textbook valve seals to me but is there anything else I should check first?
View 14 RepliesOK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.
I bought this truck a few months ago. After trying everything under the sun to try and rectify a poor running problem, it was realized that injectors needed replacing. Ended up putting in 160cc/30% unlimited diesel performance injectors. The truck has a rough idle and surging problem. After trying to install the chip from gearhead, the truck didn't run any different, ultimately (according to the shop doing the install) smoking the ECU. New stock ECU, same problem. Goes good under throttle, just idle is bad. I get weird looks at the gas station. People think it has a big cam.
7.3 Rough Idle - YouTube...
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.