Truck stalls out and cranks hard for 7-10 seconds before starting if I don't let it warm up adequately before I start driving. Transmission is hesitant to shift. Also, white smoke comes out exhaust if it's cold and I get in the throttle too much or if I hit 70+mph.
View 2 Replies2002 7.3 Power Stroke... I bought the truck about 4 months ago and I absolutely love it but over the last few weeks is has been acting funny at times, it doesn't do it all the time but it has been getting progressively worse, ill drive the truck all day and no problems when I shut it off and go to start it again it just cranks but won't fire.
* Batteries are charged and in good condition, oil is a little dirty but full, I have no codes or check engine light on, and my wait to start light seems to be working fine!
* If I supply a fuel source(starting fluid) the truck will fire but not stay running
* And let it sit for 15 to 45 minutes fires right up like there was never an issue.
* There are no blown fuses
2002 Ford F250 super duty 7.3L Diesel Automatic I crank but wont start and run.
Background:
I live in NY, last winter (2013-2014) fuel pump stopped working, I discovered this website, changed my fuel pump although mine worked fine after I did it, Power was not going to my fuel pump, took apart truck to follow wires to find the problem, wires come from the fuel pump into the CPU and Fuse box, relay is built in fuse box, changed fuse box, truck started, from early spring to summer ran without problems, in summer friend ran truck dry without filling up luckily he threw it in neutral and shut off engine rolled it to a stop, Filled up truck after a few tries it starts up. A week later the fuel filter o-ring rips and spews diesel all over engine, changed filter ran for a week and o-ring poped out again, changed to a different o-ring and ran for a month without problems. Then poped again, and again, each time approximately a week later.
Latest winter (2014-2015)
I start my truck to warm up go inside and forgot all about it, about 1.5 hours later I remember my truck is started, go outside to find it shut off with diesel all over the pavement, the o-ring blew again. I changed it, cranked the engine and it started and ran for 10 seconds before stalling. I turned the key a few times to try and have my fuel pump run, and it would crank but not start. Then it started to crank really slow,(batteries were now already on charge) it was below freezing for a good whole week now, found my oil heating plug and waited a day, cranked it the next day, cranked faster but did not start, waited another day and when I tried to start it the starter would not turn.
Today:
So today, winter is almost over(if you lived here you would understand) I find out I blew my starter and changed it, I replaced the o-ring with [ 90025K557Double-Seal X-Profile O-Ring, Oil-Resistant Buna-N, Dash Number 347 ] from Mcmaster.com as suggested on this site. I cranked the engine, It started ran for 30 seconds and stalled. I tried turning the key a couple of times to get fuel going(fuel pump seems to be working), but crank and wont run. My father suggested starter fluid, got couple cans, I was able to start the truck with starter fluid and keep it running until the can ran out.
It wont start and run on its own like it did the first time I tried.
I have a 2002 F250 7.3 with 130,000 miles. The truck was bought new by my father and is completely stock and never run hard. I was driving on the interstate at 70 mph and the cel came on for 30 seconds and went off. Not long after it went off the truck shut off and has not started back. That was around 12-20-16. I have put a new cps, icp, and ipr on it with no luck. All ford parts. I drained the fuel water separator to check the fuel pump and it filled back up. The truck is turning over good but has no white smoke witch leads me to think maybe the IDM. I'm a novice to all of this and until this happened new nothing about any of these parts but I'm learning. I do have the torque app if I should check some things.
View 14 RepliesI have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 Replies1999 7.3l 6spd standard 4x4. Just bought the truck 4 months ago knowing it had a problem that once warm occasionally would t start. Happened a few times every week or two. But wait 15 minutes and the truck would fire back up. Then it started happening more often throughout a day. And I would have to wait longer for it to cool to start it up.
Icp has been changed
Cam sensor
Pulled valve covers to check to see if there were any injector o rings failing. They were all good. Put it all back together.
Pulled the IPR and tore it apart cleaned it all out
Started driving it ran great for a week. Then today sitting at a light the truck died just as if I had turned the key off. Wouldn't start for 3 hours. The. Fired up. Took it to buddies show and started checking things out again. Both batteries load test great and fully charged. Alternator pumping out 13.5 and up.
Codes i have pulled are waste gate to high /low
I forget the number for that one. The second was P1211. Cps has been changed and ipr cleaned. Think that I should replace the ipr of this happens again?
I did get w code a few weeks ago about low voltage at module. this code doesn't appear anymore. Since I checked the plug ins all looks good. But the PCM wasn't mounted properly. So I fixed that up and checked battery connections. They were very good so I re did all of that.
Anyway. Back to the problem. After ipr clean. Drove as she should until sitting at a light a week later. Truck just quit. Would t start back up until cold. Any thoughts. New IPR? Oil in hpop within half inch from top. And I don't seem to have any oil leaks. Did oil change fuel and air filter. Not low on any fluids. I had a 1997 too and threw a bunch of cash at it like this one trying to find the issues.
So I had a reman 7.3 and 4r100 dropped in my 03 excursion.. since then the engine fires up every single time.. ONLY when the truck sits for 2 days i have this issue where the truck fires right up, runs for 4 or 5 seconds then stalls out.. It starts back up on first try and idles rough 10 seconds then it runs great.. If it only sits 1 day i dont have the issue if it sits 1.5 days it will try to stall out and catches itself from stall out and doesn't stall about 3/4 of the time. The mechanic who is a reputable diesel mechanic cant figure it out.. they called swamps and they also were unsure.
View 9 RepliesI have 2001 7.3 f250 ... I just got it about 2 months ago I drove it for maybe 2 week and it ran good the other morning I went out to start it and would not start and the way I was parked my low fuel light was on so I put 5 gallons of fuel in finally got it started sum how drove it for maybe 2 hrs parked it and wen we got back in to go it was done for hasn't started since its been down for a bout 2 weeks now I've replaced hpop, icp, pcm, fuel filter,checked idm for corrosion it all looks well, gpr,checked uvch on driver side looked good and changed cps what else do I have to go from ? No matter what it won't start good batteries cranks good but no start ...
View 14 RepliesI have a '99 F250, 7.3, CCSB with just over 127K on the clock. I went out of town for 10 days and was ready to get out of the grocery getter and into my truck. I hop in and it cranks great but would not start. I pop the hood and start with the easy stuff. Made sure all plugs/connections were good, check. Relays and fuses are still in good order (under hood and dash), check. Fuel pump was replaced less than a month ago (works great) with fuel in fuel bowl (new filter), check. Try to start a few more times with no luck, so I tinkered around for few more minutes and it starts right up and drives perfect.
Drive around, truck is on and off as usual throughout the day and go back to work next day around 10:30. Truck starts as normal. Get to work and have to run out but truck doesn't start again. After key is in on position for 15-20 minutes while checking fuses and such it starts up and runs perfect. I drive around for 20 minutes and return. I got off about 5 hours later and it doesn't start. Leave key in on position while I'm explaining issues to a buddy again 15-20 while key is on it starts right up. I drive home and park and I haven't been able to start it since.
From reading forums and watching you tube I'm leaning towards IPV or CPS but no one has described the problem as I've had. I do not have monitors, tuner, or anything aftermarket but I'm a mechanic and have a descent set of tools at home.
I have a 2002 f350 psd. I pulled it inside today to wash it. After washing it wouldn't start. Pcm is working. No oil pressure on guage and no reading on tach.
View 9 Replies2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
Need to diagnose my truck issues. On my 2002 F250 V10, when I try to start it, the engine just cranks and cranks and cranks with no fire or even hint if starting. I am not sure if it has no spark or isn't getting any fuel. I just replaced all ten spark plugs and coils less than 500 miles ago. I want to perform the fix myself, but I need to get the problem diagnose the issue first.
View 8 RepliesMy dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
I have had my excursion for almost 4 years, I love this truck. but lately we have been having issues that we haven't been able to figure out. First it has about 390K miles on it.
I ALWAYS have to plug it in. it could be 90 degrees out and I still have to plug it in. if it Is plugged in normally it will start fine. but then when I go to drive it, it wont have any power until I get like 2 miles down the road. you can push the pedal all the way down and it will go like 10mph. but once it warms up its fine. if I forget to plug it in, I will have to plug it in for about 2 hours and then it will start hard and run really rough for about 10 min. And it will blow greyish smoke out the exhaust.
But now I'm having the issue of keeping it running. it will start and run for 5-15 min and then quit and I have to wait anywhere from 10min - 1 hour to start it again.
'99 F-250 7.3 PS 2WD Automatic 246,000 miles
Jumped in my truck a bit ago and it wouldn't start, although it is turning over. The "Wait to Start" light is not coming on and the Overdrive button on the shifter is lit up OFF and won't change with me pressing the button. I've checked all the fuses under hood and inside cab with multimeter and everything checks out ok.
Also, when it was raining last week I found that when I turned on my windshield wipers the truck would die. My solution to get home was to just flip it back & forth real quick every so often so I could see out the windshield.
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil. I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. If you need any info off the scangauge let me know and I will post the exact readings. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 6 RepliesWe're currently RV camping in the Wyoming Wind River Range at 8500 ft and is getting to freezing at night. The past two mornings the truck has been very difficult to start and I got quite a bit of smoke. This morning it took two or three tries but I got it going.
View 3 RepliesI wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 RepliesHere's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
I have a 1995 f-250 7.3 liter diesel engine. Truck starts fine and runs good for a while and then it will stall. I pull over and after a couple of attempts it will start and run fine for a while. I have changed the fuel filter and put fresh fuel in but it still stalls.
View 7 RepliesI have a new to me 1999 F250 with the 7.3 engine. The previous owner installed a push button start to get around the ignition actuator being broke. Over the weekend I pulled the column and replaced the actuator but the truck will still not start with the key; with the push button it starts just fine. I'm not getting any power on the starter relay signal wire, so I suspect something in between the key and starter relay. I searched around a bit, but could not find a wiring diagram for a 1999 diesel super duty.
View 3 Replies