2002 F250 diesel ... I found these two plastic pieces yesterday on the floor near the 4X4 shifter. I noticed the other day when i step on the brake the rear view camera in the head unit comes on, so i am thinking they are either a part of the brake switch on the pedal assembly, or something to do with the shift tube.
View 2 RepliesI picked up a 1999 F-250 Super Duty with the extended cab (not the full crew cab), and have been working on restoring, upgrading, and improving it. It is in great mechanical shape, but needed cosmetic work, replacement of the mirrors and some lenses, and updating to modern tech. I've got all the key wiring in place to install a new in-dash PC head unit with backup camera and a new sub and amp to improve the audio. The problem I'm working on right now is that the head unit is a bit too deep for the double-din slot in the dash.
I could let it stick out 1.5-2" or so and trim it out, but to be honest, I'm not keen on that at all. I think it looks terrible, and I've gone to a ton of trouble already for a nice clean, sleek install and would like to keep it that way.
I've also looked and whether the screen might be divorced from the main body, or the chassis shortened, but neither of those is going to work.
I've considered that there may be someone who makes custom dashes that stick out further for situations like this, effectively deepening the stereo pocket by adding space at the front. If there is though, I can't find them.
Finally, and what seems the most likely, is that I would need to modify/reroute the air duct, and notch out the steel tube at the back of the cavity, to gain an extra 2-3" of depth.
Tires have less than 10,000 miles on them, and air pressure is within 2 lbs left to right side.
New calipers.
New soft lines.
New hard lines.
New pads.
New rotors.
New ball joints.
New tie rod ends and center link.
New front axle universals.
Brake fluid and all other parts are less than 6 months old. I can let go of the wheel and the truck tracks straight, 10mph to 100 mph. Whether I am going 10 mph, or 100 mph, when i first step on the brakes the truck jumps right. Needless to say, the faster i am going, the worse it jumps.
After first brake application, truck tracks straight. Let go of the wheel and it tracks straight from 100mph to a dead stop with brakes applied after the initial jump. Whether I am hard on the brakes or gentle, it does not pull at all. Only on the initial step on the brakes.I am at a loss as to what the heck is wrong with it.
I'm putting a new double din stereo w/ backup camera in my truck, I have everything wired except the violet/white wire (from the stereo) that needs to be hooked to a wire (on the truck) that will activate the camera when you put it in reverse. I cannot figure where this wire is on the 2012 for the life of me.
View 3 RepliesSo my 2012 rearview camera was super clear and this 2013 is super blurry! Only difference is that this one has has MyFordTouch with no nav. The 12 had the nav option. Camera lens its self looks clean.
Oh yeah and the thing automatically autoplays my voicemails as soon as I start the truck and I hate that it does that. Can't figure out how to get that from happening.
2013 F350 Lariat with the factory OEM rear view camera. I am replacing the tailgate with a 5th wheel tailgate for a few months and would like to still retain the convince of a rear view camera.
I have obtained a Ford camera harness to use as a jumper for a non OEM camera which comes with the standard basic RCA wiring which I plan to mount to the bottom of the 5th wheel tailgate.
My hope is to wire the camera direct to the Ford wire harness which is a 6 wire pigtail. Which wires on the camera mate to which wire on the trucks wire harness.
Was wondering if there is a way to adjust the view angle of the back-up camera? Mine appears to be a little off center.
View 6 RepliesI bought a 2011 F250 with nav and backup camera. the backup camera only shows in the rear view mirror and NOT in the nav screen. How to program it to show in the nav screen also?
View 7 RepliesI have an 02 f150 xl, I'm taking the stock head unit out and replacing it with a Pioneer 1900. I didn't buy a connector I'm just splicing the wires together, I know I shouldn't do it that way but it's to late now, what my problem is, there are three ground wires coming from the truck and the new head unit only has one ground, I just looked wiring diagrams up for both head units and that got pretty much everything done, just there are two speaker ground wires that are black and green, and then a regular black ground wire, I'm not sure if I should connect them all together or cap them separately, because I connected everything up and the head unit wouldn't turn on...
View 2 RepliesI just installed a new Pioneer head unit in my 2002 Excursion. Everything works great except it doesn't work on accessory power. I used a harness to harness hook up but I basically just connected like colored wires. When done I had three extra wires coming from the truck harness, black with a white line, and two orange wires... one may have had a black stripe. All others were connected. Do I have to get power off of a wire from the ignition switch or did I not connect one I should have?
View 4 RepliesI just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 RepliesMy 02 F250 periodically has no acccesories like electric windows, radio, and AC do not work for a minute or so. It has been doing this for awhile and seems to be getting more frequent and I am concerned that it might go out on a trip. It runs OK when this is going on and usually happens on the first start on the day. I was thinking maybe the ignition switch?
View 7 Replies2002 Ford F250 super duty 7.3L Diesel Automatic I crank but wont start and run.
Background:
I live in NY, last winter (2013-2014) fuel pump stopped working, I discovered this website, changed my fuel pump although mine worked fine after I did it, Power was not going to my fuel pump, took apart truck to follow wires to find the problem, wires come from the fuel pump into the CPU and Fuse box, relay is built in fuse box, changed fuse box, truck started, from early spring to summer ran without problems, in summer friend ran truck dry without filling up luckily he threw it in neutral and shut off engine rolled it to a stop, Filled up truck after a few tries it starts up. A week later the fuel filter o-ring rips and spews diesel all over engine, changed filter ran for a week and o-ring poped out again, changed to a different o-ring and ran for a month without problems. Then poped again, and again, each time approximately a week later.
Latest winter (2014-2015)
I start my truck to warm up go inside and forgot all about it, about 1.5 hours later I remember my truck is started, go outside to find it shut off with diesel all over the pavement, the o-ring blew again. I changed it, cranked the engine and it started and ran for 10 seconds before stalling. I turned the key a few times to try and have my fuel pump run, and it would crank but not start. Then it started to crank really slow,(batteries were now already on charge) it was below freezing for a good whole week now, found my oil heating plug and waited a day, cranked it the next day, cranked faster but did not start, waited another day and when I tried to start it the starter would not turn.
Today:
So today, winter is almost over(if you lived here you would understand) I find out I blew my starter and changed it, I replaced the o-ring with [ 90025K557Double-Seal X-Profile O-Ring, Oil-Resistant Buna-N, Dash Number 347 ] from Mcmaster.com as suggested on this site. I cranked the engine, It started ran for 30 seconds and stalled. I tried turning the key a couple of times to get fuel going(fuel pump seems to be working), but crank and wont run. My father suggested starter fluid, got couple cans, I was able to start the truck with starter fluid and keep it running until the can ran out.
It wont start and run on its own like it did the first time I tried.
I have a 2002 F250 7.3 with 130,000 miles. The truck was bought new by my father and is completely stock and never run hard. I was driving on the interstate at 70 mph and the cel came on for 30 seconds and went off. Not long after it went off the truck shut off and has not started back. That was around 12-20-16. I have put a new cps, icp, and ipr on it with no luck. All ford parts. I drained the fuel water separator to check the fuel pump and it filled back up. The truck is turning over good but has no white smoke witch leads me to think maybe the IDM. I'm a novice to all of this and until this happened new nothing about any of these parts but I'm learning. I do have the torque app if I should check some things.
View 14 RepliesI have some LED strips i bought, some i am going to install under the door sills to light my nerf bars/steps. The rest i am installing under the bed rail to light the inside of the bed. I want them to come on with the interior lights. So when i hit the unlock button on my key fob, or open the door said lights will come on.
View 7 RepliesI have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 RepliesComming back from hunting today my truck suddenly lost power and stepping on the accelearator had no effect at all. We were on the highway thru the mountains but on a fairly level stretch for a few miles. Managed to pull the truck and toy hauler over and the engine was running fine but stepping on the accelerator had no effect. The check engine light came on every time I stepped on the throttle and went out when I released it. It started fine but no throttle response. Switched around a bunch of relays and checked the fuses and still nothing.
Not liking my parking spot i tried to see if it would move down the road at an idle but it would not. Then I thought to try it in 4 wheel low and as the shoulders were soft it wouldn't move forward so tried reverse and went back a foot, forward again and moved a foot and a half. did this several times and all of a sudden the throttle responded, took it out of 4 wheel and it ran fine all the way home. What would have caused this? I was ready to call a tow truck which would have been several hundred dollar bills for where we were and with the trailer
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
I have a 2002 F250 Super Duty. Was driving it and it started to lose power and shut off. Then wouldn't start like out of fuel. No engine light no codes. Truck has 155k on it. So just because I replaced fuel pump. Truck runs but not right it's ruff no power kinda back fires in exhaust. I check wires and plugs under valve covers all seems ok. I ran truck and pulled each injector loose and engine would stumble. As in they are working. I replaced cps. Just because still the same. Then the truck started running right. But the truck runs but has knock but knock goes away and truck has full power. Yes oil is full and I change it regularly. The problem is off and on like electrical.
View 7 RepliesMy 2002 f250 starts but has no throttle, I did replace the throttle body, still no luck, i did find a wire on the shiffter that had a bad spot , fixxed it still no throttle, code reader says it passes with no codes, I disconnected both batteries and waited 15 to 20 min, reconnected them, started the truck and let it idle for 20 min so what do i need to do now. I just cant figure it out....
View 7 Replies