2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 RepliesI just bought a 2002 F250 7.3 4x4 auto. It had a TS 6 position tuner installed. In stock mode, I got about 11 mpg. I wasn't too impressed. I found that when I left it in 75hp mode, my mileage went up to 21. I drive easy and try to keep shifts at or below 2,000 rpm. The problem is that, when in any position other than stock, my transmission shifts HARD.
My question is: what's going on here? Does the TS change the transmission shifts? Or is the extra bump in power enough to stress the tranny? Based on the factory gauge, the transmission is not running hot. The fluid is nice and pink with no odors or metal shavings. I'd hate to prematurely kill my transmission, but nearly doubling my fuel mileage is hard to pass up.
The first has I replaced my tranny with a stock 4r100 tranny and torque that only has 75k on it. The guy was doing a 6-speed swap. After I had the tranny and torque converter and a new tranny cooler installed, the tranny shifts real hard. I think it may be from my DP Tuner. Even on my economy tune driving it very easy sometimes, it jolts into gear pretty good.
I was wondering if I could just get a shift kit to maybe correct that and if so if I would have to drop the tranny to install the shift kit. I saw a bully dog kit for like 75 bucks, however, I don't really have the money to have the truck in a shop and I would really like to not drop the tranny and not lose all my tranny fluid if possible (very expensive).
Also my other issue, the truck in warm or cold weather is very hard to start. Half of the time it takes two tries to start it. It will crank and crank and no go. Then the second try it fires right up. It has two new batteries, where do I start? Is it possible that the starter is just getting old or is it fuel or oil pressure related possibly?
I have 99 f350 v10 4x4 and trans shifts great under light rpms but 2-3 shifts very hard. At wide open from about 35 mph it will shift down and take off like a bullet but wont shift until I lift my foot and then it bangs hard from 2-3. All other gears are smooth. I did some searching and have found some threads saying it could be an accumulator spring that is broken? Truck has 115,000 miles on it. love the truck but want to fix this before it does some damage.
View 1 RepliesHere is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 Replies2000 powerstroke 4r100 transmission. It has 155k just had it rebuilt and the shop is having a night as am I. It was shifting hard and the o/d off light would start flashing after you drove it a while. Its still doing the same thing and the shop checked the whole wiring harness and replaced the accumulator twice believing they got a bad re-manufactured one. The only code I can pull is a 605 pcm read only memory error. Could the cause be a bad pcm? The shop doesn't seem to have a clue at this point and I'm out 2500. IV taken it back twice now and Iv driven it a total of 35 miles since the rebuild...
View 1 RepliesI have a 2002 Elantra GLS with the 4 speed auto and in the mornings or after sitting in lot at work for 9 hours, the trans shifts hard from second to third (almost as if it has a shift kit) and slips a little from third to fourth. The TPS was changed once and that seemed to eliminate problems at the 26K mark. I have 109K on it now and at around 80k took it in to the dealer with the receipt for the same complaint and what was done the first time. Dealer kept overnight and said there were no problems. I do know from having a performance TH350 built that the harder a trans shifts (up to a point) the longer it will last due to less friction on clutches and bands.
View 6 RepliesI drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
I have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 RepliesMy 2001 7.3 was smoking excessively and I rebuilt the turbo and the center cartridge was at fault for that. I'm still having some of the problems I was having before with a lot of smoke at cold start (I have to hold the accelerator down while I start it and it takes about 10 seconds to start) even when I hold it I have to keep it held for about 5-10 seconds before the RPMs get to where they should be. And it smokes like crazy.
Then after about 3 minutes warming up, or 30 seconds of me holding it at 3500 rpm, the idle smooths out and it only smokes a little. Then once I start driving it doesn't smoke a lot unless I go hammer down then it puffs some white smoke. I took the oil cap off and it isn't huge amounts of blow by cap just rattles off. Can ford buzz test and see if I only have 1 or 2 bad injectors? Could this be anything other than injectors? It has a ts6 on it with 24xxxx miles with factory injectors.
I put a ts6 on my 2001 7.3. I love it shift points are better and truck has a lot more power. But I've noticed when I shift truck shifts into 3 (especially going uphill) I get a really weird turbo sound where it acts like its gasping for air (I have 6637 air filter) and then it shifts kinda rough into third. If I put chip on stock setting it doesn't do either of the things I described. Do I have loose turbo boots somewhere or possible bad turbo bearings?
View 4 RepliesI have a 2001 F350 Dually 7.3 w/260K miles. Hard starting, it has to be plugged in all the time. Occasionally/most of the time, blows white smoke at 50 to 60 mph or at high rpm. Replaced TPS and now runs totally different on starting, still hard to start but better throttle response on starting. Once started, I have to pedal it to keep it running, which seems to have little response as it would as if it was a direct throttle linkage attached to a carburetor...follow me? After a while, it will idle by itself. However, it still has flat spots when out of idle and at high rpm. Has gotten to the point that I can't trust to drive it.
View 4 Replies2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
Ok so here is my problem now. I'm sure its in the tramny but not sure what else. My shift from 3-5 has always been a little hard. Yesterday on my way to work I noticed shifts 1 thru 3 were hitting hard. Once I got up to 65 mph it was okay. Then pulling into work when I shifted to reverse it didn't go into gear right away and then it would hit into gear. Later that evening on my way home from work it was shifting the same but seemed worse. Then my tow/haul light started flashing and it seemed like the torque convertor wouldn't lock in. It would just stay in 5th gear and the more throttle I gave it the rpms would go up but I would only get a little response from it. Then a few miles down the road it just completely shut off on me. It will not even try to turn over. I could also hear a noise coming from underneath the truck. Something ive never heard before. I really need to figure this out
View 14 RepliesHaving transmission problems? Everything I've read before says these transmissions are better than gm Allison's and they can handle up to 600 horse before you gotta worry about beefing them up but mines starting to act funny.
How important is the transmission tune? My truck it's tuned with the spe hot tune and trans tune. Didn't like the way it clunk bang hard shifts though so I ran factory trans tune for a while but it felt very soft like it was slipping when I got after it on the performance setting of spe hot so I went back to spe trans file.
I get a little twang sound that sounds like it's coming from the trans between 3-4 gear shifts, initially only heard it after getting on it hard in performance but it's getting worse and happens on stock power level under light acceleration now sometimes. Also I lost all gears briefly and it wouldn't shift into manual at all when I stopped to turn around the other day.
Working fine in drive but when I shifted out to reverse it had nothing in any gear and manual wouldn't light up on the display. I shut it off and restarted the engine and it came back and worked fine after that but not sure what happened there, don't think it's good though. Did using the stock transmission file with the hot engine tune or the hard clunk bang custom trans file up my trans, freak malfunction?
'00 PSD w/ 291k on the clock. Starts easily, runs good, only complaint is (what I consider to be) the soft shift of the tranny. Years ago, when I bought it, it came with a Super Chips Tuner. I've never max'd it out, just usually run on the performance tow. Is there any way to clean up the shifts and make them a bit quicker with less slip. When it's time to shift, dammit, I want it to "SHIFT", not slide into gear. I don't expect it to hit the gears like a manual valve bodied drag car tranny. But, there should be something to fix this without spending a bunch of $$$..
View 4 Replies2007 escape 4wd 3.0. I've notice some random hard shifts for the past month and today the trans has trouble shifting out of 1st. If I get the rpms between 3,000-4,000 and ease off the accelerator pedal it shifts into 2nd without drama. It will not shift at lower rpms with the same easing off the pedal. The trans light is steadily blinking.
View 7 RepliesHave to get rpm's over 2k before trans will engage, then in between shifts I either have to let off throttle or let engine rev over 2k to get trans to shift...
View 3 RepliesI'm getting a sound every now and then of what sounds like i'm running over rumble strips on the side of the highway. I'm guessing it's the trans grinding. Any thoughts?
View 8 RepliesI notice my trans temp gets really hot fast. For instance just moving my trailer from front of my house to side yard makes temp go to 250. Without any load and driving a couple miles it does the same thing. It's been doing it since I installed the trans temp gauge just trying to figure out what's up.
View 14 RepliesI bought this truck with 200000 miles and its been flawless, its now 900 short of 600000.. I use it to haul everyday.. nothing heavy mostly a car or truck and every once in a while a skid steer. I got 560000 out of my trans, i take it easy. lol
at 350k I installed a Jw valve body drilled pump, tripple disc converter and solenoid pack.. at 560k it went, i pulled it and brought to a guy i trust as much as you guys trust BDS.. Ive had what Ive called a vibration since day one, could be a shudder, could be a shimmy.. what ever.. I brought it back and he says nothing would do that from a trans, so I went through drive shaft, new t case ripped apart rear end and its still there and I have just been dealing with it.. about 2 months ago it started acting up in first. when I pull down to drive I get the normal bump and start to go, it feel like the truck slows, then another bump and it climbs normally with the shudder.
took it back and he said maybe a stuck valve in small VB, so I pulled it and went down there and it was fine, I reinstalled and still does same thing. I then put a pressure gauge on it and it swings as it should sits around 70 psi and will climb, only in first it will climb and fall back to 70 like a switch was flipped, and the rest of the gears bleed off slowly or normally.. He then said it could be the big valve body, so I swapped that one out with another and no real change, maybe its a bit more noticeable.
I am at a loss. Could this be loose feed bolts? Could the shudder that I can feel at most speeds be the 1 gear slipping a tiny bit all the time? I am told that first gear is always on.. this truck has been a dream until this trans issue..