Ford 7.3L Power Stroke (1999-2003) :: 2001 - Strange Turbo Sounds And Hard Shifting Into 3rd With TS6
Nov 20, 2015
I put a ts6 on my 2001 7.3. I love it shift points are better and truck has a lot more power. But I've noticed when I shift truck shifts into 3 (especially going uphill) I get a really weird turbo sound where it acts like its gasping for air (I have 6637 air filter) and then it shifts kinda rough into third. If I put chip on stock setting it doesn't do either of the things I described. Do I have loose turbo boots somewhere or possible bad turbo bearings?
View 4 Replies
Advertisement
I have a 01 7.3 F-350, 120000. I rarely get down hard on the go pedal but a while back I did and heard at pressure whistle just before it would shift. I thought a bad turbo hose so I replaced them all. 'While working on the hose mounts I cleaned up the castings for a better seal'. The hose replacement seemed to get the running but the whistle is still there. I am thinking a leak on the manifolds for the Y-Pipe connection OR does the turbo have a release valve that can make a whistle sound?
View 8 Replies
Are we supposed to put anti sieze on the turbo to pedestal bolts. They were really hard to break loose when I pulled it Cheater bar tight. 18 ft. lbs sound right ?
View 2 Replies
This is is a truck I hardly know anything about. My wife bought it while I was deployed for herself and when it comes to vehicles she's an idiot. No, really she told me she bought it because at horse shows everyone else has one.
I noticed an oil leak and had a reputable shop look at it. They told me it was coming from some seals on the turbo. Long story short there is a brand new turbo on there, stock replacement. Now it seems very under powered and shifts hard. Pressing down anything more than 25% throttle will cause hard shifting or no shifting at all. It'll stay in second until I ease off the throttle.
I tried searching a few terms but I'm not sure what to look for. I don't know if someone has messed with the tuning. Broken clamp on the turbo. Replaced and everything is back to normal...
View 4 Replies
I have a 01 f250 7.3. Every once and a while when I go to start my truck it make a strange noise, very similar to the sound a vehicle makes when you try and start it while it's running. if I let off the key and try again it will start. Sometime it will do it 2-3 times. So far I have never had it not start after a few tries. Can't seem to put a reason behind when and why it does it. Sometimes it will go weeks without happening, sometimes it will happen twice in a day. Starter is year old but put a cheap one in it. Is it my starter or something else.
View 13 Replies
So I have a 2000 F-250 7.3 and my over drive won't work. I also had hard shifting from 3rd to 4th and 3 gear wouldn't try to shift until about 2500 RPMs which is high. I replaced solenoid pack and no change. I have rebuilt the tranny and found that OD snap ring had came off I put upgraded spiral ring on. When I went on a test drive I found out nothing had changed except shifted smoother. So I changed valve and accumulated body still no change. Truck is throwing 4 codes:
P0733 Gear 3 incorrect ratio
P0750 Shift Soleniod a fault
P0783 3-4 shift error
P0541 intake air heater a circuit low
Could it be PCM??
View 14 Replies
I have run into a problem. My early '99 7.3 PSD decided to throw a very hard shift at me the other day, lit up the SES light and I had to limp it home going 5mph.
I looked on here and found most problems that caused power loss/engine die and replaced the ICP, IPR, EBP and tube, and the CPS. I also did an oil change after all of that to make sure everything was clean when I went to start it up.
BUT, when I tried starting it, nothing happened. It cranks, but does not start. What is the problem? I watched hours of videos and read hundreds of pages of instructions on how to replace everything, and now the truck won't start.
View 10 Replies
I have a 2001 3/4 pickup. Sometimes the over drive light flashes. When it flashes it shifts really hard and sometimes it won't shift into 4th until I mash the overdrive button. Sometimes the light doesn't flash at all and it doesn't have any trouble shifting at all. Is it a solenoid? Or wiring issues?
View 6 Replies
2000 powerstroke 4r100 transmission. It has 155k just had it rebuilt and the shop is having a night as am I. It was shifting hard and the o/d off light would start flashing after you drove it a while. Its still doing the same thing and the shop checked the whole wiring harness and replaced the accumulator twice believing they got a bad re-manufactured one. The only code I can pull is a 605 pcm read only memory error. Could the cause be a bad pcm? The shop doesn't seem to have a clue at this point and I'm out 2500. IV taken it back twice now and Iv driven it a total of 35 miles since the rebuild...
View 1 Replies
I recently purchased a used 2001 E350 with a 7.3L and the transmission is not shifting properly. It will go into Reverse no problem, put it in "D" and it starts in high gear and will not shift out. If I manually shift from 1 to 2 to "D" it works fine and will even go into OD. It will not down shift on its own either. What should I do to fix this issue?
View 2 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 Replies
I have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 Replies
My 2001 7.3 was smoking excessively and I rebuilt the turbo and the center cartridge was at fault for that. I'm still having some of the problems I was having before with a lot of smoke at cold start (I have to hold the accelerator down while I start it and it takes about 10 seconds to start) even when I hold it I have to keep it held for about 5-10 seconds before the RPMs get to where they should be. And it smokes like crazy.
Then after about 3 minutes warming up, or 30 seconds of me holding it at 3500 rpm, the idle smooths out and it only smokes a little. Then once I start driving it doesn't smoke a lot unless I go hammer down then it puffs some white smoke. I took the oil cap off and it isn't huge amounts of blow by cap just rattles off. Can ford buzz test and see if I only have 1 or 2 bad injectors? Could this be anything other than injectors? It has a ts6 on it with 24xxxx miles with factory injectors.
View 14 Replies
I have a 2001 F350 Dually 7.3 w/260K miles. Hard starting, it has to be plugged in all the time. Occasionally/most of the time, blows white smoke at 50 to 60 mph or at high rpm. Replaced TPS and now runs totally different on starting, still hard to start but better throttle response on starting. Once started, I have to pedal it to keep it running, which seems to have little response as it would as if it was a direct throttle linkage attached to a carburetor...follow me? After a while, it will idle by itself. However, it still has flat spots when out of idle and at high rpm. Has gotten to the point that I can't trust to drive it.
View 4 Replies
2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
View 14 Replies
Ok I have had this noise going on for about 1 week before transmission went out. I just built the trans and its still there.
I had a mishap years back with front end hub bearings so I replaced with New Timken Bearings. Well that wasn't it but at least I know where I
stand with those. It starts making a noise when slowing down about 3-5 seconds before coming to a stop. I thought maybe the carrier bearing in
driveshaft?
Pinion bearing in rear diff? I need to service the parking brakes on rear so I may pull it down and go through it.
View 6 Replies
Well I am at a loss now. Rebuilt the turbo with a new wheel and kit from Riffraff. I still have no power, no boost and no codes. The new wheel whistles. I can hear it. It sounds way better than the old one. But still no power. I really don't know what to do now.
View 14 Replies
As I was getting ready to leave town with the tractor loaded up, I was accelerating with the turbo spooling up when I heard a bit of a pop and lost power (engine still running and all, just very low power like you get when the turbo fails). I wasn't far from the shop so I came back and started getting a lot of white smoke out of the exhaust, it doesn't smell like diesel, probably more like oil. Definitely smoke, not coolant. I pulled it around back and shut it down to go grab AE and scan it and it shows a P0475, starting it back up has light smoke at idle and it idles fine but as soon as you give it any throttle it starts smoking pretty badly.
Researching it looks like the most likely cause for this is the EBPV itself but before tearing it down that far. This is the only code it's showing.
Truck has 272k on it, turbo was rebuilt a couple of years ago but we didn't do anything with the pedestal at that time. I guess in retrospect, I probably should have done the EBPV delete and the resistor fix then but I didn't think about it at the time.
On another note, my AE is not showing any of the system test for some reason, the drop down is blank. I have version 7.0.1, so it's an old version but I'm working on an old truck, so... What that might be? I've got the truck pulled into the shop now to let it cool down. I'll probably let it sit overnight and take the turbo and EBPV out tomorrow unless someone has a better suggestion...
View 14 Replies
So my understanding is that if your turbo is leaking oil, you either need to rebuild it or get a new turbo cause the one you have is shot.
I have some oil leaking, but it's not a ton. One one of my buddies was telling me that it's possible that the amount that is leaking is normal due to the PCV (Pressure Control Valve) system, or something like that. Here are a few shots of the turbo, as well as the boots that are leading up to the turbo.
View 9 Replies
While my turbo is out I decided to delete the EBPV. I removed the butterfly and rod, & pounded in some 3/4 inch freeze plugs. Are there any mods that need to be done to the pedestal, or can I just leave it the EBPV plunger unhooked? It's not leaking, but will it leak if left unhooked? Or do I have to gut it and tig weld the oil gallery's
View 14 Replies
