Ford 7.3L Power Stroke (1999-2003) :: 2001 Started Blowing Blue Smoke
Jan 8, 2016
01 7.3 247k.
Yesterday went to get on the freeway I looked back and saw a cloud of what looked like blue smoke. I'm in northern Utah and it's cold but the truck runs fine, I haven't noticed any change in performance. Turbo still builds boost. I pulled the fuel filter cap last night to check fuel color and it was clean.
I do have the CCV mod done. I also pulled to IC Pipe off the turbo and there was a little oil in there but not much, should there be any at all with the CCV mod? Where to start.
View 14 Replies
Advertisement
Recently since the weather has been cold. between 0-30 degrees or so. My 2002 7.3 with 161k on it is smoking a decent amount i think. far more than i ever remember it smoking thats for sure! anyways its a combination of blue and white smoke and it doesnt last long when the truck starts maybe 1 minute and the smoke stops.
But I also notice when i rev the truck maybe around 1200 rpms the engine shakes very bad. so i was thinking maybe a glow plug went bad making the engine seem like its missing. but even when its warm i rev it up to 1200 and i still feel the engine shake slightly. Maybe im just being picky when its warm? I need to test the glow plugs and go from there but i want opinions about that issue. the truck sits for 4 hour periods and every time i start it i have smoke. I will pay attention tomorrow morning if it smokes after being plugged in all night and post my findings.
My other issue and this typically happens when its below 20. sometimes i will go to accelerate after coming to a complete stop and the truck kinda has a very weak rev to it then just takes off like the tps took a break on me. sometimes i have had it jerk the truck when the throttle catches and other times it creeps at first then takes off like a boost of power.
lastly and this little issue happens most noticeable at 35 mph. i feel a surging im thinking this is related to the tps but i put the truck on cruise control and i still feel the surging. maybe this ties into my second issue? bad TC? ive plugged in my scanner and the only thing jumping out at me is the icp hunts about 100 psi or more at idle. i plan on doing a WOT test on the HPOP, ICP and IPR tomorrow and see if maybe this is just a weak hpop causing my issues.
Repairs i have done:
new 8th injector and all new injector seals about 25k miles ago.
new ipr
new icp
have CCV mod done and 4 inch turbo back exhaust
new map sensor
cleaned out the EBP sensor and tube but that was probably 40 or 50k ago now.
gray cps and i cant remember when i put that on.
gutted the EBPV
bellowed up pipes
no tunes the truck is factory as far as that goes.
View 11 Replies
I have a 7.3 that's running rough. Started it the other day it ran alright but started blowing white smoke. Bought a oil and fuel additive i was going to run through it. Came a few days later, it stated up and was real loud and sounding like it was loping. It blew a good amount of white smoke, but it just smelt like real heavy diesel. Now i can only turn it over and it won't start.
View 2 Replies
Ok, I have owned my truck for almost a year and it has 151,000 miles. I have noticed on a few occasions puffs of blue smoke and especially at night in the headlights behind me I notice a lot of smoke when I'm getting into the throttle hard. Under normal driving conditions I don't usually see anything.
Today I noticed it when I was backing my camper(8000lbs) up a small hill onto the side of my garage. It was puffing blue pretty good going up the hill while it was under load.
I have no check engine light on, the truck seems to be running fine. My oil consumption is about 2 quarts every 3-4000 miles. I tried the blow by test with the oil cap but besides some smoke out the filler neck no problems... I don't know very much about diesels so for me to try and trouble shoot this is a problem.
View 9 Replies
Got a 2002 7.3 F-350 with 300,000 miles and for the last couple of years I've been getting blue smoke on cold morning start ups and its been gradually getting worse, it clears up after about 30 seconds and all is normal,No loss of performance, Oil consumption is minor, however I hate a vehicle that blue smokes, I'm guessing my issue is valve seals are worn, I was wondering if it is possible to replace the seals while the heads are on the engine? and was also wondering how much time it would take to fix? as i would have to have it professionally done. I know its hard to guess a time frame and everyone is different. Sounds like textbook valve seals to me but is there anything else I should check first?
View 14 Replies
I have a 07 6.0 powerstroke, I had 2 bad injectors so I replaced all of them with reman's. I had a problem with them coming loose. the first time this happened it hydrolocked the motor, number 8 cylinder. so I pulled all the injectors and replaced all the seals and washers and torqued them down a little more than spec like 27 lbs. it runs great and starts great even at 25 degrees but I noticed this morning that when starting it up after it sits (cold) it blows blueish smoke until late it warms up and I accelerate. is this normal? should I check fuel filters? oil in fuel?
View 14 Replies
Early 99 7.3. Runs ok has a slight miss at idle however every injector when unhooked makes a change. Has white and blue smoke From the exhaust. Has enough blow by to blow the oil cap off as your unscrewing it. My question is, I know engine restore is bad for these trucks but I can't afford to rebuild the engine. If I run the restore and then clean the IRP once the truck dies is this going to mess anything else up. Do you think it will by me a few months to save up for a rebuild
View 9 Replies
SO, I've owned a 92 f250 7.3 for 10 years and it's got over 340k miles on it. Well, she is getting tired so I'm debating replacing the truck with a SLIGHTLY newer model.
I've found a truck that is a 99 7.3 powerstroke with a 6 speed manual and 260k miles. Knowing these engines I feel this truck has at least another 100k in it if the thing was somewhat taken care of. The issue is that the fella that has it for sale says it ran great for years and one day started blowing white smoke while driving. Other than this new issue it runs fine.
So my question is, what could be the issues causing the white smoke? I always thought white meant unburned diesel or maybe antifreeze. Head gasket comes to mind but it's not something I've ever dealt with.
I like that he parked it when it started having issues. Sounds like someone who doesn't completely trash their vehicles. Too high given the condition? Truck looks and sounds pretty good aside from the smoke, pretty reasonable condition.
View 13 Replies
I am a mechanic and tow operator running a late 99 f350 7.3 6 speed cab and chassis wrecker. This truck has had a hard life and has been neglected for quite some time, and now has become my baby/headache. Truck starts great, idles nice, and will run great for about 5 minutes until it starts billowing white smoke that smells like fuel and loses all power. If you continue to drive it it will die. Sounds like it's dropping cylinders and will barely idle. If you stop for 5 minutes or so and let it idle it will smooth back out and will run great again for another minute or two, then right back to stumbling.
Using torque app, hpop pressure looks good when it's running well. Peaks at 3k, IPR maintaining 30-40% max. As soon as it stumbles you can see the hpop drop to 5-600 and the IPR will climb to 65%. Let it idea bit and they go back to normal, and stay good until it stumbles again.
Ive changed the fuel pump, ICP,rebuilt FPR, change fuel filter, pulled and cleaned the fuel tank (metal tank, no delamination, looks perfect inside). Pickup screen looked good. Cleaned the IPR, cleaned the hpop reservoir, there was no screen inside. Checked voltage at fuel pump, 11.78 across the pump with it running. Pulled valve covers, no noticeable leaks around injectors. Injectors have less than 5k miles. Remans with 100% larger tips.
To me it seems like the lpop is not keeping up with the hpop under load, starving it until you idle and let it catch up. Could it still be bad injector orings? Bad lpop? Something I'm not thinking of?
View 7 Replies
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
View 4 Replies
Moving my worldly goods from California to Oklahoma in a rented 26' box truck with my wife following in our '02 F350 loaded to the gills with my lathe, mill, air compressor, weld and assorted machinery. Just west of Deming NM it started to blow lots of white smoke and down on power. Some rattling noises from the engine when throttled up & won't reach 3000RPM.
Had it towed to an impound yard for storage. Plan on sending a flat bed to pick it up when we get to Tulsa.
Any experience with a tilt back trailer capable of loading & transporting this truck that weighs around 17,000 pounds? My plan is to continue on to Tulsa & make arrangements from there.
View 14 Replies
I have a 2003 F250CC 7.3 with 200,000 miles on it. I just purchased this truck about a month ago. My question is it blows black smoke. A little at idle but mostly when you give it any pedal. I have replaced all of the injector o rings and that didn't make a difference. Then I had it tested and it failed a CCT test on #2 cylinder. I have an injector to put in it, but am curious to find out if 1 bad injector would be enough to make it smoke all the time. I keep getting P1211 ICP pressure above desired. I had a friend of mine who used to work at a ford garage take a look at it with his computer and he said that everything looks good other than the CCT test.
View 14 Replies
Need to diagnose this before I start ripping wires:
Truck started blowing the # 8 fuse under the hood tonight (15 amp #8 - trailer tow electronic brake illumination, park lamps, trailer tow park lamp relay coil fuse) which also controls the dash board lights (can't see gauges at night) and the tail light lights (brakes lights work) are out too. Figure I have a short somewhere.
View 14 Replies
My santa fe 125k on it engine start to blow little blue smoke when start up ...
View 1 Replies
Having trouble with motor, driving home one day heard a noise under the hood. Then a lot of grey smoke started coming out of exhaust. Got the truck hauled home notice fuel was coming out at the number 7 cylinder at exhaust port. Thought it might be the injector just put rebuilt ones in, thought I might have received a bad one. I switch the number 7 injector with the number 3 injector. Did not make a difference still have fuel leaking out of exhaust manifold at the number 7 cylinder and a lot of grey smoke coming out of exhaust. Not sure where to start looking next? Could it be the injector cup is the problem?
View 14 Replies
I had the engine out of my truck (7.3 with e4od) to do manifolds. Anyway, I got it back in and started it up. Since there was air in th fuel lines it had to crank a couple seconds but started up. I looked and now fluid coming out, then it sat for a few minutes running and I took it for a drive. While sitting in the driveway it wa smoking a bit. But I thought it's from the oil I got in the exhaust while drilling two of the manifold bolts and soaking the bolts with ATF/acetone. After about half a mile I thought that maybe it's more oil then that would cause... So I went back. I looked and the inside of the exhaust is covered with oil, and the rear of the engine is also.
When it was out I capped all of the open ports so I could pressure wash the grease off. Also, I flipped the CCV so I could do the delete. During instal, I missed the cap on the CCV and it was not able to breath. I think that maybe it built up pressure and blew the valve cover gasket? It looks like it's coming from the right cover on the backside; I had not taken this cover off while the engine was out. How much pressure does it build? Is it possible that it could have blown the gasket out? I have done the oil cap trick to test blowby and it always passed the test. What it could be? For the leak on the engine and why it's in the exhaust?
View 13 Replies
I have a 2003 ford escape V6 and i have notice when i start it' after setting overnight i notice some blue smoke for a little while then it's stop What could be causing this.
View 1 Replies
Just happened today right after I bought diesel. thought it may be water in fuel but after researching wondering if it is injector, etc. It starts every time knocks real bad sometimes for a minute, but clears up to idle ok. During idle no smoke, slightest acceleration however produces white smoke harder I accelerate more it plumes and it smells like diesel in the air.
Cannot get past 15 or so mph till switching into 2nd gear then 25mph max. Had to drive 4 miles like this I can say it cleared up and drove 1/2 mile until I had to stop at a traffic light then going from idle to acceleration again ran bad rest of way home another 2 miles.
A few years ago I did have a rough idle and accel. similar and it ended up being the broke pick-up/sending unit in tank (but of course that was when you get to around 1/4 tank of fuel and didn't run bad above that much fuel in tank), plus there was almost or more than a gallon of water in tank. I have done the mod for the fuel pickup with hoses, filter canister, etc. but wondered at first today if I had gotten bad gas or water in the tank again. Not sure how that much water got in the tank to begin with but that was bout 5 or 6 years ago.
Truck has over 200k miles and Ive had it for 11 years. In the morning will check the ICP sensor by unplugging look at fuel filter bowl, etc. A question I have is: Is water heavier than diesel, would it run thru my line first? thinking diesel is heavier than gas because of oil content....
View 2 Replies
Truck is a 02' F350 xlt crew cab, 7.3l, 4x4, 4R100, manual transfer case, 125,000 miles.
So me and the family were pulling out of the driveway tonight and electrical smoke starts blowing out the vents. My wife had just plugged a cheap USB charger into the auxiliary outlet above the cup holders for only 30 seconds. I immediately pulled back into the driveway, yanked the charger out, and found it had melted a hole in the side of it. No smoke had come from the charger or the outlet. The outlet looked fine and wasn't hot to the touch. I pulled the dash off real fast and started grabbing wires, feeling for anything that was hot or melting. I couldn't find anything.
I pulled the cover off under the steering wheel and couldn't find anything. I never turned the truck off while I was looking. After a few minutes, I noticed that the cover over the fuse panel was warm. Pulled the cover off and felt every fuse end and they were all cool to the touch. The relays in the middle were all pretty warm(almost hot to where I couldn't touch them). I was still faintly smelling the burnt smell and I couldn't tell if it was just stuck in my nose. I disconnected the batteries and we had to switch cars(heading to a bbq).
So I just got home and I'm going to start looking for any obvious signs first. What could be going on at the panel? So far, everything is still working. I haven't found any blown fuses.
View 7 Replies
My turbo started to have oil on the top of it. I don't know where it's coming from at all, it started to blow blue smoke but not all the time. You can also smell the oil burning off.. someone said maybe the pcv system but not sure. Still new to the vw world only owned the car for about 4 months. Trying to add pics but it's not working.. Will keep trying
View 3 Replies
I would I have a 01 7.3 e350 with 111k miles. I drove the van a couple of days ago.it sat for 2 days and now it wont go past 30mph.the van shakes crazy and went when i hit the petal no power with smoke coming out the tail pipe sometimes. When I shut the van off and restart it to drive it,it sounds better. I changed the fuel filter with motorcraft and changed the oil. Here is the kicker. It ran good after I changed the fuel filter the whole day and now its 4th of july and I went to get some drinks and it happened again.
View 11 Replies
