Ford 7.3L Power Stroke (1999-2003) :: 2001 - Hard Start - Flat Spots At High Speed?
Apr 27, 2017
I have a 2001 F350 Dually 7.3 w/260K miles. Hard starting, it has to be plugged in all the time. Occasionally/most of the time, blows white smoke at 50 to 60 mph or at high rpm. Replaced TPS and now runs totally different on starting, still hard to start but better throttle response on starting. Once started, I have to pedal it to keep it running, which seems to have little response as it would as if it was a direct throttle linkage attached to a carburetor...follow me? After a while, it will idle by itself. However, it still has flat spots when out of idle and at high rpm. Has gotten to the point that I can't trust to drive it.
View 4 Replies
Advertisement
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
I have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 Replies
My 2001 7.3 was smoking excessively and I rebuilt the turbo and the center cartridge was at fault for that. I'm still having some of the problems I was having before with a lot of smoke at cold start (I have to hold the accelerator down while I start it and it takes about 10 seconds to start) even when I hold it I have to keep it held for about 5-10 seconds before the RPMs get to where they should be. And it smokes like crazy.
Then after about 3 minutes warming up, or 30 seconds of me holding it at 3500 rpm, the idle smooths out and it only smokes a little. Then once I start driving it doesn't smoke a lot unless I go hammer down then it puffs some white smoke. I took the oil cap off and it isn't huge amounts of blow by cap just rattles off. Can ford buzz test and see if I only have 1 or 2 bad injectors? Could this be anything other than injectors? It has a ts6 on it with 24xxxx miles with factory injectors.
View 14 Replies
2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
View 14 Replies
I have a 2003 MCV36R Camry SPortivo, Australian spec. Have owned it for 12 months. Have had power issues.
Replaced:
plugs
fuel filter
O2 sensors (engine)
MAF sensor
Throttle Position Sensor
Have checker EGR valve - all looks good
Have coded OBD II, no codes coming up
Current issues are:
Flat spots from 1000rpm to approx 3000 rpm (esp on gear change from 1st to second)
Once flat spot stop, it powers up enough to throw you back in your seat.
Also, rough running when sitting on constant speed, esp bad between 65-85 Km/h.
Have recently done a 800km trip. half way through, isolated the EGR valve. Running probs have improved greatly, but still lacks power.
View 5 Replies
We're currently RV camping in the Wyoming Wind River Range at 8500 ft and is getting to freezing at night. The past two mornings the truck has been very difficult to start and I got quite a bit of smoke. This morning it took two or three tries but I got it going.
View 3 Replies
When I turn on my fan for the AC or vent or heat, it works just fine on the first and second settings. When I move the fan speed to the third and last speed, I hear this sound that sounds like the blower fan is hitting something. I turn the speed back to the lower two settings and noise goes away. Sometimes I turn it back to the higher settings and the noise actually will go away but most of the time the noise is there.
I pulled the blower motor out yesterday and set it to where I can turn it on while out of the compartment and I didn't really notice a noise. I wonder if the noise is there but I am just not hearing it since it is not enclosed in the compartment? I also noticed there is a crack in the fan where it mounts to the shaft starting at the shaft and extending out one direction and also 180 degrees the other direction. Thoughts on if the motor is bad or just the fan? Or even something else that I may not be seeing?
View 4 Replies
2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 Replies
My e99 f250 has been getting harder and harder to start over the last year.
I think one of my batteries is dying or dead but it still cranks fast while it does.
For instance when I tried starting today it seemed to crank just like normal but their was some relay clicking inside the cab that was abnormal.
My understanding is aside from cranking no power is required to start the motor? what if the dead battery is taking some cranking amps from the good battery preventing the computer from getting juice?
would the truck throw a code if it was a glow plug?
View 9 Replies
Alrighty let me see if I can get everything. 01 6speed 450hp at rear wheels. Comp 910 valve springs, valve seals, 238-80% injectors, full RR, 38r turbo, napa air filter, Hydra with Gearhead tunes, 5"exhaust, 280k about 100k on rebuild. All mods done 40k ago. Now I have a horrible up pipe leak I assume is causing the low boost #'s I have to do another clutch so up pipes will be fixed when tranny is out this week. But I'm using 1-2 gallons of oil every 3k or so. I smell burning oil when I get out, mainly if I am getting on it then stop. I haven't pulled the fuel filter to see if its a injector o ring. (Tonight's project) but turbo sounds fine, I'm going check for shaft play tonight. What could be my loss of oil without it actually leaking on the ground?
View 14 Replies
The first has I replaced my tranny with a stock 4r100 tranny and torque that only has 75k on it. The guy was doing a 6-speed swap. After I had the tranny and torque converter and a new tranny cooler installed, the tranny shifts real hard. I think it may be from my DP Tuner. Even on my economy tune driving it very easy sometimes, it jolts into gear pretty good.
I was wondering if I could just get a shift kit to maybe correct that and if so if I would have to drop the tranny to install the shift kit. I saw a bully dog kit for like 75 bucks, however, I don't really have the money to have the truck in a shop and I would really like to not drop the tranny and not lose all my tranny fluid if possible (very expensive).
Also my other issue, the truck in warm or cold weather is very hard to start. Half of the time it takes two tries to start it. It will crank and crank and no go. Then the second try it fires right up. It has two new batteries, where do I start? Is it possible that the starter is just getting old or is it fuel or oil pressure related possibly?
View 2 Replies
2001 F 350 7.3 183,000 miles.. The problem is the longer it sits the harder it starts.. when it does start it runs VERY ruff!!! it takes 10 min or so to run on all cylinders.... This is my first diesel..
View 4 Replies
My truck is hard to start when cold and I suspect glow plugs. But it is not showing any codes? If it is a glow plug or glow plug relay at fault , should it throw a code?
View 10 Replies
Just got myself a gently used Econoline E-350 7.3 Diesel and was loving it when she ran:
E-350 7.3 Diesel
Recently I have been having some charging issues. It started with it intermittently having a hard time to start, especially when it was warm. I carried a jump box with me and that always seemed to work. Then I noticed the voltmeter on the dash dropping. It went down to the 8 and I was like something is wrong.
Checked the battery voltage, it was at 9.6v. OK, maybe alternator isn't charging. Advance Auto tested the alternator, said it was bad. I replaced alternator. No difference. I pulled the battery and ran it on a conditioner to bring it up to proper voltage. It's now at 12.6v resting. Starts the van no problem. When running though the voltage doesn't increase to 13-14 volts like it should though telling me the alternator isn't doing it's job. Increasing engine RPM actually decreases voltage? Checked all the obvious things like bad grounds but everything seemed clean.
The only thing that was fishy was when I pulled the three way plug from the alternator, one of the pins had corrosion on it. I cleaned it up before installing the new alternator. I didn't do a diode test on the new alternator because I figured it was new, but hey maybe I got a lemon?
Anyway I'm going crazy trying to figure out where the problem is. All fuses are ok. Is there an external regulator or something I should be on the lookout for? Is there anything else that could be causing a non charging issue? The battery was manufactured in 2014 so it's relatively new.
And on a random note my ABS light is now on?
View 8 Replies
I put a ts6 on my 2001 7.3. I love it shift points are better and truck has a lot more power. But I've noticed when I shift truck shifts into 3 (especially going uphill) I get a really weird turbo sound where it acts like its gasping for air (I have 6637 air filter) and then it shifts kinda rough into third. If I put chip on stock setting it doesn't do either of the things I described. Do I have loose turbo boots somewhere or possible bad turbo bearings?
View 4 Replies
My 2003 7.3 f250 has trouble starting whenever the temperature is less than 65 degrees. If it is less than 50 degrees I have to plug it in for it to start. Once it starts it runs rough. I let it warm up and it still runs rough. Once I start down the road I'll get on it a bit and it takes off like something lets loose. It then runs geat for the rest of the day but does seem to still crank a little more than it should when I restart it through out the day.
The pickup has 152000k
List of repairs I have done to the truck:
-new gpr
-new glow plugs
-new uvch both sides
-new valve cover gaskets
-new blue cps
-new fuel filter
-new batteries everstart maxx 65n
The truck has an afe air intake, straight exhaust, and a super chips tuner set on mileage saving. It blows white smoke when first started but clears up pretty quick.
View 13 Replies
So I've been having issues with starting my truck lately. It was really hard to turn over, would start really hard when it did and would blow some black smoke. Turns out my starter was bad so I replaced it with a DB Electric high torque starter. Now it starts up great... for the most part.
I'm still having some black smoke when it's a cold start and/or I have the key set to "On" to warm the glow plugs for a few seconds. It's almost like the starter is turning over the engine, but for the first few turns it sounds empty or hollow (at least that's the best way I can describe it). After the first turns it will sound normal how it's supposed to and will fire up shortly after but with some black smoke.
If my car is already warm it cranks right up without any smoke unless I have the key set to "On" for a few seconds to warm the glow plugs like I said earlier. Pretty much if I warm the glow plugs it makes it harder to start up for some odd reason.
What might cause this or how to fix it? Maybe some of my glow plugs are going bad, or possibly my IDM? I used to have the P1670 code by itself, however, that went away when I replaced the starter. I also just replaced my camshaft position sensor just to be sure it wasn't going bad. I've also been having some boost pressure leaks if that's relevant at all.
View 8 Replies
When it is cold out side like 20 degrees I'm having problems starting my 2000 7.3 I'm cycling it about 5 times and misses smokes white for a bit then stays running I was thinking of changing out the fuel filter. What it could be?
View 6 Replies
But it starts. '99 F250 PS. Had code P1670, cleared it. No other codes. Started truck back up and ran KOER test with AE(which I'm not very good with). The code did not come back. It is hard to start plugged in cold or warmed up. I have WTS light and it goes out(glow plugs are original). RPMs are slow to come up (almost starts before it kicks in). Doesn't matter if fuel tank is full or not. Oil level is fine. Batteries are charged and check good. Starter checks out ok. Buzz test was ok. Now when I run KOER do I need to do anything other than hitting the initiate button?
View 10 Replies
My wife has been telling me our '01 E-350 (Econoline) with 7.3 is taking several attempts to start in the mornings, like it's not even trying to fire. It will crank like wild but no fire and then it will fire usually and sometimes run a little rough but no always.
Tonight she called me from across town and it won't start at all, cranks like wild but won't start, chug or anything.
The WTS light is working fine, the truck runs great and idles smooth all other times, just been giving grief when starting in the mornings (warm outside 70 degree plus ambient temp). I haven't had the truck do it to me but she has explained it well enough.
I do get a SES light for overboost when I run it hard (PHP tuned) but it always goes away and hasn't caused any issues. Could this be the ICP acting like this? If so, is it true that I can just unplug it and the truck will start by using default pressure?
View 14 Replies
