Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - Vibration At Idle
Oct 28, 2015
I change my motor in my 01 f350 ccsb to a forged rod one from a 97. When I put the thing in my inexperience cause me to screw up my torque converter in turn ruining my transmission. So after a rebuild I put it back in and she fit like a glove. Ever since I put the engine in i get a vibration at idle.
After I realize I screwed up the torque converter I figured that was the cause of the vibration. But now I know the trans is in properly I still have this vibration I'm thinking it's the position of the motor. I installed new motor mounts when I put the motor in but they were quite a bit off from the original points on the cross member.
My only idea to rectify this was to reinstall the original ones and try to position the motor back where it was prior to the engine swap. Or should I be looking elsewhere?
View 10 Replies
Advertisement
I have a 2000 Ford F350 7.3 with the auto and 262,000 miles on it. As far as I know everything is stock on this truck. It has been a great truck but lately its been making a strange noise. It almost sounds like an exhaust rattle or vibration but it is intermittent. Its not really loud it can be heard best in the cab at idle. I've looked all over on the truck and haven't found anything. I can't pinpoint where it is coming from. I tried starting the truck with the serpentine belt off no change.
I took the inspection plate off the bell housing and couldn't see any cracks the torque converter bolts appear tight, and the starter is not engaged while running. I've read a few forums on the torque converter going bad. It looks to me like its more the 99 trucks that had trouble with that. Did the torque converter issue carry over to the 2000's? Would a torque converter/transmission problem be intermittent?
View 3 Replies
I'm looking at a 2001 Excursion with 242k miles. Truck is all stock, and everything checks out well. The only thing is there is a slight vibration at idle, that increases quite a bit when the engine is revved to about 12-1500rpm. Ran a CCT, and #8 was flagged. I know that can be somewhat normal depending on the CPS, right? Otherwise the truck is smooth, and in great shape. Should I be concerned about what feels like a slight miss on #8?
View 3 Replies
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies
I have a 2000 F350 4x4 CC 7.3L 323,000 miles auto trans. I have removed my tuner just to make sure that it was not the issue. The truck will run fine then all of a sudden the idle will rise then fall or shudder or go up and down and sometimes it will just Die but it always restarts. No trouble lights at all. I am not sure what is causing the issue?
View 6 Replies
I have noticed a small vibration at 40-50 mph for a few weeks now and was unsure to the issue.. ( I just checked wheel bearing ect , last night ) . This morning at a stop light she started to white smoke shake and clack, somewhat violently, when I pull away from a stop it seems to smooth out and run normally.. A stuck injector ? Toast injector ?
View 11 Replies
I have an early 99 F-350 with 268K miles. It is bone stock right down to the factory exhaust. A couple months ago I started have a rough idle and surging while driving problem. I never got a check engine light but I borrowed a scan tool from a friend and pulled the following codes: P1690 (wastegate solenoid), P0381 (glow plug circuit malfunction), P0269 Cylinder 3 Contribution/Balance Fault, and P0284 Cylinder 8 Contribution/Balance Fault.
I did some research and everything I read said it was most likely the CPS. So I changed the CPS. The truck ran fine for for a few days but then it started acting up again occasionally. I noticed that most of the time when it acted up was at start up when the engine was cold and I also figured out that if I shut the truck off and re-started it (sometimes I had to do it 2 or 3 times) it would clear up and run normal.
A buddy of mine that has a 2000 F-250 said he had a similar problem with his truck and it ended up being the ICP sensor. We switched his ICP with mine and I changed my oil at the same time (because it was due for an oil change). My truck ran flawless for over 2-weeks (over 200 miles) so I put a new ICP in my truck. Note: my buddy did not experience any problems with his truck with my ICP in it.
I've put about 700 miles on the new IPR and the truck has started to act up again. Once again shutting the truck off & re-starting it will clear it up and still no check engine light. I took it to a local "diesel specialty shop" while it was running rough and they hooked it to their scanner and got P1280 (Inj. Control Pressure Low), P1690 (Wastegate Solenoid Fault), P0381 (Glow Plug Indicator), P0269 Cylinder 3 Contribution / Balance Fault, and P0284 Cylinder 8 Contribution / Balance Fault.
They never did anything other than hook it to a machine & check the codes but their diagnosis is my High Pressure Oil Pump is going bad and my #3 and #8 injectors are going bad. They recommended I let them replace all 8 injectors and the High Pressure Oil Pump. The problem I have is they can't give me a REASONABLE explanation as to why re-starting the truck a few times clears up the problem.
View 14 Replies
I just bought a 2001 F350 diesel with 120k miles on it a couple weeks ago. Friday I headed out to Oregon with my 16 foot enclosed trailer filled with jet skis (about 4-5k pounds) for a competition. A few minutes after being on the freeway I noticed the truck did not have good power. About 30 min later while climbing a steep grade the truck almost went dead.
I started at 60mph and by the time I got to the top i was at 15mph with the throttle pinned. the motor sounded funny and shook the truck more then normal. After wards on the down side of the grade the truck started to act normal. I took it to my buddies house and switched trucks because I didn't trust if for the 13 hour drive.
Today I talked to a mechanic at the dealership and he said that it sounded like injector o-rings to him. I went home, pulled the valve covers and started the motor to see if anything is leaking. steam was coming from the valve area and the down spouts on the injectors was flowing oil. The thing that looked especially abnormal was one of the injectors looked like fuel was dribbling from it. I don't know if that is a problem or not. I couldn't tell if it was fuel or oil but no other injectors had fluid coming out near the wire connections.
View 14 Replies
2001 F350 just rebuilt the turbo, did the EBPV delete now no power.
View 5 Replies
The other day I had been driving about 3 hours and truck went dead then back on, it happened two more times in about 30 minutes.
(2001 F 350 Dually 7.3 A/T 2 wd.)
View 4 Replies
2002 F350 single wheel 4x4, 280k miles chipped with a 6
My problem first started when the bottom of my sending unit broke off in tank causing me to run out of fuel at 1/4 tank. I dropped tank and repaired. A week later I noticed fuel dampness on my tank and discovered I crossthreaded cap on sending unit. About this time I started getting a shutter at slight acceleration only and a harder hit at idle. I thought air in lines so I dropped tank and reassembled. No air in line at all now but I still have a shutter so I replaced fuel filter in case of obstruction. No luck. Now since I have owned truck it has been a pain to crank in cold weather if it wasn't plugged in over night. It has been hard lately even in moderate weather since shutter started so I replaced both batteries today.
I replaced the ICP today also because I noticed the other day when there was oil on and around harness to it and when I unplugged it today the truck changed idle and there was oil inside. After I changed it I took it out and it still had the shutter and sound of a miss. At about 8 miles in it just died going down the road. I coasted to the side and it cranked right back up and drove home. The shutter doesn't fill as bad but there. Also I live in the mountains and on my way home after cutoff I had chip in Stock position and had to put peddle to the floor to climb hill. I've never had to do that. I'm getting worried I work for a living and caint keep throwing money at it aimlessly. I'm thinking at this point IPR or CPS. But I'm no mechanic so I could be completely wrong.
View 12 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
I have a 2001 F350 7.3 the truck will at random times loose power and almost shut down. A while back I had an issue with the uvch plugs and changed that out. Truck ran fine till I got some dirty fuel from a diesel tank at my friends farm. I did the hutch mod cleaned the tank and now have a frame mounted screw on filter before the pump. I cleaned the fuel bowl and changed the filter. Fuel pressure stays at 59psi and drops to 56psi wot. The truck is tuned with an edge programmer. After these mods the truck ran awesome for over 2000 miles. Now it has the above stated problem. I have fuel and hpop guages along with egt and boost. During the problem egts will increase rapidly and it seems like it is starving for fuel.
Hpop gauge reads 3300psi or above during wot and shows good pressure during these mishaps. I have auto Enginuity and I get a different reading at wot of only 2600 psi. The hpop gauge is tapped into the icp sensor per instructions and has been installed this way for a while with no issues. The tune has been on the truck for over 40000 miles. The only thing that I can come up with is it will occasionally throw a p1211 under wot or pulling my Gooseneck Dump Trailer when loaded. However it acts up sometimes and doesn't throw the code. Sometimes you can shut it off and start it back up and it's fine other times it will last for the whole day. My only guess is low pressure from the hpop but I don't reflect this from my gauge only on AE at wot. Wouldn't a bad pump act up all the time? Am I correct to think it is just the ipr?
View 2 Replies
I have a 2001 F350 XLT with cloth seats. In 2003 I upgraded those seats to power seats.
- When I upgraded to power seats I did not run a new power wire. Since my 2001 was at least fused for power and heated seats I located the Power seat 30amp power wire.
- That wire is located on engine compartment fuse #15 (Circuit 5298 as I recall) and Dark Green. It comes through the firewall and runs down the drivers side kick panel along the floor and then intersects with the power and ground seat belt wires that ran under the seat.
- The ground wire was coiled and attached to a ground stud behind the drivers side kick panel.
About a month ago I had a mouse get in and chew my seat wiring to shreds. I built my own harness and am good to go there, however since I had these seats all apart I decided to replace the foam and add HEAT.
So that brings me to the specific question. In the engine compartment fuse box, there is a 30amp positive wire for Heated seats. My schematic says it is a 14 gauge wire RD/BK on circuit 1153.
Where in the heck is this wire? I have literally tore the dash apart looking for this wire.
- I have verified the following with my fluke continuity tester.
- It is not part of the four customer access wires that drop on the right side of the interior fuse panel.
- It is not part of the tow wire bundle.
- I have checked the bundle that the Dark Green Power seat wire is in and there are no RD/BK wires in that bundle. I also poked the other 2 14 gauge (Yellow/Blue) wires in that bundle and verified they are not them.
-I have checked the three wire bundles behind the passenger side glove box and was unable to locate.
- I have verified it is not stored behind the compartment below the cigarette lighter.
I am looking for info which wire I am talking about and knows where Ford stored them when not used by having the XLT Trim with cloth seats. Yes I am aware that I can run an additional wire with a 30 amp fuse to the batter, but I would prefer to use the system and fuse that was designed for this.
View 2 Replies
My one owner 2001 7.3l F350 w/ 265K miles died a few days ago at a traffic light. First time it has ever died on me other than a CPS. This dying was an almost instantaneous with no CEL light, unlike the CPS's hiccuping and dash light up. I put it in park and it started right back up like normal. I continued about my errands and made it home. I have since driven it two more times the same distance and it has not died.
What I have done on this truck the past year.
-Replaced ICP -3/14
-Rebuilt IPR and checked IPR plug -6/14
-Replaced fuel filter every 7500 miles and I am probably due another one of those now
-Replaced air filter - 4/15
-Cleaned out both the sensor and the exhaust back pressure tube
-replaced CPS w/ dark blue unit from RiffRaff in -8/14
-checked main harness over driver valve cover and placed a piece of heavy duty wire cover wrap where they touch the valve cover -8/14
UVWH replace in 2008
Have a new IPR and pigtail coming just because I wanted to eliminate a bad solenoid on it. I also have a Torque Pro w/ blue tooth adapter on an LG tablet that I have yet to set up....but am working on it Will the truck throw any codes if the CEL didn't light up?
View 14 Replies
I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 Replies
I have a 2001 F350 4x4. My transmission went out a while back. It would only go in reverse. I had it rebuilt and it is still having issues. When I take off with speed from a dead stop it shifts late...about 3000 RPMs. It shifts fine until it shifts into overdrive. It will go into to 4th then right into overdrive causing the truck to act sluggish.
I'm looking into my truck not starting well at any temp too! I didn't know if it could all be connected some how. My mechanic said that when he first started my truck it had a MAP sensor code. He also said that when he unplugged that sensor it didn't change the way the truck ran..Still like crap. I have changed all glow plugs relays and even did the mod to it.
View 6 Replies
I have been having problems with my truck for about 6 months now. It start in Sept when my fuel pump went. I got a new pump and went to change it just to have the back clip break off. I fixed the line after getting 2nd degree burns from the boiling water I had to use to expand the line and installed the new fuel pump. Didn't fix anything.
At this point is was dropping below freezing every night ( I live in Canada in the mountains) so I thought it might be my plug relay again... changed that. After that my started has always missed so I figured I would change it out and sure enough the power bolt on the starter was broken. Changed it.
Then it started smoking and I read up on the quarter trick so I figured why not try that. I checked everything and they all checked fine but I am a glutton for punishment and figured I would do that valve cover gasket. So opened it up to find one of my glow plug wires on my harness was burnt up. I have a spare truck for parts so I grabbed the wire and replaced it. Still no change.
Today it was spitting out the usually raw diesel that I have gotten use to but when I was opening the gate to get a manlift for work I smelt oil just to find my turbo coved and the V had a small pool of oil happening there. I added 4L of oil and tightened up my valve cover back bolt on the passenger side... it may have fixed the leak but didn't have time to check.
I backed up to the manlift and it lagged a bit so I gave it a pump of the peddle and it died. Now it won't start. Charged batteries and tried after it cooled down but still no go.
In short my truck has been smoking for about 4 months now. It shutters at low RPM and stalls at the bottom of hills if I gear down on the hill (we have really steep hills around here). I have changed my oil three times in the last 6 months but it keeps coming out black (which it always has). No water in fuel or oil. Once and awhile it had problems starting when it was warm but after bellowing out massive amounts of smoke it would start. The truck turns over but wont start. There is no power where it died so I have to come home and charge the batteries every time they get low but even after it cooled down it still wouldn't start.
View 14 Replies
My truck will set an idle fine but when I hit the throttle it will die.
View 3 Replies
I have seen a number of post about front end vibs associated with steering and braking. I have had a hard time finding these posts and decide to post my vib/noise accompanied when brake and steering applied.
I too have a vib/noise coming from the front at low speed braking and turning (mostly parking lots and such).
About 5-6 months ago (around 90k miles) I noticed a high squeal at high rpms. I thought it had something to do with the belt so one day while driving up the grapevine pass (I-5), under high rpm, I turned the AC on. The squeal went away, I turn the AC off the squeal came back, I was pretty sure it was the belt and hopefully not the AC compressor.
10k miles later, I finally got to changing the serp belt. After I changed the belt, I immediately heard a rough vibration noise when braking and then when PS is under strain. It seams like it comes and goes when it wanted to, but now its always under the low speed parking lot conditions. Sometimes the vibration can be felt in the floorboards.
I haven't gotten to fix'n it yet lol... as I don't know what the problem is. I'm finding it hard to believe that a serp belt could be the cause of vib/noise when braking/low speed turning. One thing for sure, the vib/noise instantly occurred when I changed the serpentine belt. What might be going on here?
View 8 Replies
I recently purchased a 2001 excursion 7.3 after driving it for a while I have noticed a significant clunk and vibrate in the rear end. I have read a lot of people saying it could be the slip yoke needing lube which I intend to do but most are saying that their clunk is at start and stop.
Mine is between 30 and 60mph when I let off the accelerator I get a clunk followed by a vibration and when I get on the accelerator it is just the clunk. Does this sound like the slip yoke to yall or am I looking at something more? I have tried turning the drive saft and there is no play in it at all.
View 14 Replies
