Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - No Power Especially While Towing
Sep 14, 2009
I just bought a 2001 F350 diesel with 120k miles on it a couple weeks ago. Friday I headed out to Oregon with my 16 foot enclosed trailer filled with jet skis (about 4-5k pounds) for a competition. A few minutes after being on the freeway I noticed the truck did not have good power. About 30 min later while climbing a steep grade the truck almost went dead.
I started at 60mph and by the time I got to the top i was at 15mph with the throttle pinned. the motor sounded funny and shook the truck more then normal. After wards on the down side of the grade the truck started to act normal. I took it to my buddies house and switched trucks because I didn't trust if for the 13 hour drive.
Today I talked to a mechanic at the dealership and he said that it sounded like injector o-rings to him. I went home, pulled the valve covers and started the motor to see if anything is leaking. steam was coming from the valve area and the down spouts on the injectors was flowing oil. The thing that looked especially abnormal was one of the injectors looked like fuel was dribbling from it. I don't know if that is a problem or not. I couldn't tell if it was fuel or oil but no other injectors had fluid coming out near the wire connections.
View 14 Replies
Advertisement
I have always seen other trucks blow black smoke with towing up a hill but mine for the most part has not. I pulled my 5er to CO this summer and notice my truck starting to blow black smoke. I consider myself a very conservative driver. I always stay around 65 MPH while towing and never push my truck up the hills. I always try to keep the RPM around 2000 and let the MPH fall where they may until I reach the summit. With the black smoke I'm starting to see what is my truck trying to tell me? It's not bad but would like to fix now before it becomes something more.
2001 F250, 4X4 crew cab, 7.3 with 205,000 miles.....
View 10 Replies
2001 F350 just rebuilt the turbo, did the EBPV delete now no power.
View 5 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
I have a 2001 F350 7.3 the truck will at random times loose power and almost shut down. A while back I had an issue with the uvch plugs and changed that out. Truck ran fine till I got some dirty fuel from a diesel tank at my friends farm. I did the hutch mod cleaned the tank and now have a frame mounted screw on filter before the pump. I cleaned the fuel bowl and changed the filter. Fuel pressure stays at 59psi and drops to 56psi wot. The truck is tuned with an edge programmer. After these mods the truck ran awesome for over 2000 miles. Now it has the above stated problem. I have fuel and hpop guages along with egt and boost. During the problem egts will increase rapidly and it seems like it is starving for fuel.
Hpop gauge reads 3300psi or above during wot and shows good pressure during these mishaps. I have auto Enginuity and I get a different reading at wot of only 2600 psi. The hpop gauge is tapped into the icp sensor per instructions and has been installed this way for a while with no issues. The tune has been on the truck for over 40000 miles. The only thing that I can come up with is it will occasionally throw a p1211 under wot or pulling my Gooseneck Dump Trailer when loaded. However it acts up sometimes and doesn't throw the code. Sometimes you can shut it off and start it back up and it's fine other times it will last for the whole day. My only guess is low pressure from the hpop but I don't reflect this from my gauge only on AE at wot. Wouldn't a bad pump act up all the time? Am I correct to think it is just the ipr?
View 2 Replies
I have a 2001 F350 XLT with cloth seats. In 2003 I upgraded those seats to power seats.
- When I upgraded to power seats I did not run a new power wire. Since my 2001 was at least fused for power and heated seats I located the Power seat 30amp power wire.
- That wire is located on engine compartment fuse #15 (Circuit 5298 as I recall) and Dark Green. It comes through the firewall and runs down the drivers side kick panel along the floor and then intersects with the power and ground seat belt wires that ran under the seat.
- The ground wire was coiled and attached to a ground stud behind the drivers side kick panel.
About a month ago I had a mouse get in and chew my seat wiring to shreds. I built my own harness and am good to go there, however since I had these seats all apart I decided to replace the foam and add HEAT.
So that brings me to the specific question. In the engine compartment fuse box, there is a 30amp positive wire for Heated seats. My schematic says it is a 14 gauge wire RD/BK on circuit 1153.
Where in the heck is this wire? I have literally tore the dash apart looking for this wire.
- I have verified the following with my fluke continuity tester.
- It is not part of the four customer access wires that drop on the right side of the interior fuse panel.
- It is not part of the tow wire bundle.
- I have checked the bundle that the Dark Green Power seat wire is in and there are no RD/BK wires in that bundle. I also poked the other 2 14 gauge (Yellow/Blue) wires in that bundle and verified they are not them.
-I have checked the three wire bundles behind the passenger side glove box and was unable to locate.
- I have verified it is not stored behind the compartment below the cigarette lighter.
I am looking for info which wire I am talking about and knows where Ford stored them when not used by having the XLT Trim with cloth seats. Yes I am aware that I can run an additional wire with a 30 amp fuse to the batter, but I would prefer to use the system and fuse that was designed for this.
View 2 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
I pulled with my 2000 F250 7.3 for the first time yesterday pulling a 12,500 5th wheel and then again today with an 18 ft ski boat weighting around 3500 for both the trailer and boat. I had this same issue pulling both.
Today when pulling the boat/trailer i was behind a slow moving truck and when we hit a hill with a passing lane i merged over and wanted to start passing him. We started off at around 45 mph up the hill and as I started pushing the pedal I wasn't gaining any speed and my rpm's didn't even get over 1500. It felt like a stall and continued that at around 45-50 mph up the hill (about a 65 degree slope). When I'm not towing the truck runs great, plenty of power and averaging around 16 1/2 mpg.
Only mods i have is a 6647 Napa filter, muffler delete and it's running the same 4 position TS tuner from the original owner. During normal operation I run it at the 75hp gain and when towing i use the 50hp gain.
In both instances i could see black smoke coming from exhaust when pushing the pedal but my rpm's wouldn't go up and truck maintained the slow speed going up the hill. Once at the top it drove normal and picked up speed without any problems.
View 14 Replies
I want test my fuel pressure. What is a good gauge or kit to buy? My truck has lost power towing and is now starting to miss a little. I'm wandering if i my problem is in the tank. Is there a good scan tool that would diagnose things too?
View 14 Replies
Towing a 5th wheel at about 10,000 lbs total. Towards the end of out 9 hour trip home and going upgrade the truck begins to loos power and the engine starts making some bad sounds. Although its hard to hear it starts about 45 seconds in and continues later when going uphill. the truck also made a very high pitched squealing/scraping sound (not a belt) like it may have been coming from the turbo. Oil temp was about 220, trans temp at 170 at the time of the event.
Truck has 216k, stock, upgraded trans cooler, original fuel pump.
Here is the video : YouTube.....
View 12 Replies
My dad recently bought 2006 6.0. He has had it about 2 and half months. Has the egr delete kit installed. The truck has ran great. Up until Wednesday the 3rd. My dad headed to Ut to pick up our new quads. While heading up a small grade with empty trailer in tow. Truck went to limp mode, fan kicked on, orange wrench came on on dash board. He pulled over let her cool down turned her off.
Checked fluids Then started her back up and she was fine. That has happened 3 times. Now he is on his way back (tow haul mode turned on) and it is doing it again. She hasn't went into limp mode yet. As soon as the fan kicks in my dad pulls over immediately and puts it in park. And lets her cool down checks fluids. This issue only happens mid way up a grade. So my question is...... What is causing this? How do we fix her and make her a happy truck again.
View 7 Replies
The other day I had been driving about 3 hours and truck went dead then back on, it happened two more times in about 30 minutes.
(2001 F 350 Dually 7.3 A/T 2 wd.)
View 4 Replies
My one owner 2001 7.3l F350 w/ 265K miles died a few days ago at a traffic light. First time it has ever died on me other than a CPS. This dying was an almost instantaneous with no CEL light, unlike the CPS's hiccuping and dash light up. I put it in park and it started right back up like normal. I continued about my errands and made it home. I have since driven it two more times the same distance and it has not died.
What I have done on this truck the past year.
-Replaced ICP -3/14
-Rebuilt IPR and checked IPR plug -6/14
-Replaced fuel filter every 7500 miles and I am probably due another one of those now
-Replaced air filter - 4/15
-Cleaned out both the sensor and the exhaust back pressure tube
-replaced CPS w/ dark blue unit from RiffRaff in -8/14
-checked main harness over driver valve cover and placed a piece of heavy duty wire cover wrap where they touch the valve cover -8/14
UVWH replace in 2008
Have a new IPR and pigtail coming just because I wanted to eliminate a bad solenoid on it. I also have a Torque Pro w/ blue tooth adapter on an LG tablet that I have yet to set up....but am working on it Will the truck throw any codes if the CEL didn't light up?
View 14 Replies
I change my motor in my 01 f350 ccsb to a forged rod one from a 97. When I put the thing in my inexperience cause me to screw up my torque converter in turn ruining my transmission. So after a rebuild I put it back in and she fit like a glove. Ever since I put the engine in i get a vibration at idle.
After I realize I screwed up the torque converter I figured that was the cause of the vibration. But now I know the trans is in properly I still have this vibration I'm thinking it's the position of the motor. I installed new motor mounts when I put the motor in but they were quite a bit off from the original points on the cross member.
My only idea to rectify this was to reinstall the original ones and try to position the motor back where it was prior to the engine swap. Or should I be looking elsewhere?
View 10 Replies
I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 Replies
I have a 2001 F350 4x4. My transmission went out a while back. It would only go in reverse. I had it rebuilt and it is still having issues. When I take off with speed from a dead stop it shifts late...about 3000 RPMs. It shifts fine until it shifts into overdrive. It will go into to 4th then right into overdrive causing the truck to act sluggish.
I'm looking into my truck not starting well at any temp too! I didn't know if it could all be connected some how. My mechanic said that when he first started my truck it had a MAP sensor code. He also said that when he unplugged that sensor it didn't change the way the truck ran..Still like crap. I have changed all glow plugs relays and even did the mod to it.
View 6 Replies
I have been having problems with my truck for about 6 months now. It start in Sept when my fuel pump went. I got a new pump and went to change it just to have the back clip break off. I fixed the line after getting 2nd degree burns from the boiling water I had to use to expand the line and installed the new fuel pump. Didn't fix anything.
At this point is was dropping below freezing every night ( I live in Canada in the mountains) so I thought it might be my plug relay again... changed that. After that my started has always missed so I figured I would change it out and sure enough the power bolt on the starter was broken. Changed it.
Then it started smoking and I read up on the quarter trick so I figured why not try that. I checked everything and they all checked fine but I am a glutton for punishment and figured I would do that valve cover gasket. So opened it up to find one of my glow plug wires on my harness was burnt up. I have a spare truck for parts so I grabbed the wire and replaced it. Still no change.
Today it was spitting out the usually raw diesel that I have gotten use to but when I was opening the gate to get a manlift for work I smelt oil just to find my turbo coved and the V had a small pool of oil happening there. I added 4L of oil and tightened up my valve cover back bolt on the passenger side... it may have fixed the leak but didn't have time to check.
I backed up to the manlift and it lagged a bit so I gave it a pump of the peddle and it died. Now it won't start. Charged batteries and tried after it cooled down but still no go.
In short my truck has been smoking for about 4 months now. It shutters at low RPM and stalls at the bottom of hills if I gear down on the hill (we have really steep hills around here). I have changed my oil three times in the last 6 months but it keeps coming out black (which it always has). No water in fuel or oil. Once and awhile it had problems starting when it was warm but after bellowing out massive amounts of smoke it would start. The truck turns over but wont start. There is no power where it died so I have to come home and charge the batteries every time they get low but even after it cooled down it still wouldn't start.
View 14 Replies
My truck will set an idle fine but when I hit the throttle it will die.
View 3 Replies
Where I can get the head light to fog light wiring harness..it is almost as hard as finding the holly grail..... 2001 f350 7.3 .......
View 9 Replies
I have an issue with my 2001 f350 7.3 PSD. Intermittently it will not start. It will crank really quick, but will not even try to start. I think it is not getting fuel. There are no CEL codes and I have a WTS light and the tach is moving while cranking. I hear a clicking/buzzing sound coming from under te center opf the dash. When I hear that sound it will not start. checked fuses and relays and it started before. not sure if removing the fue made whatever reset. this has happened a couple times. Now it will not reset. When I remove the number #24 fuse under the hood, the clicking stops. when i crank it, but still doesn't start. When it starts in runs perfect. Drained the batteries trying to trouble shoot, but have them charger now.
View 14 Replies
2001 f350. 7.3 has 350k on the engine. Last week it cut out and stalled it was about 15 degrees and though.. fuel had jeld... it warmed up.. didn't happen again. Then two night ago.. happened 4 times in a row then it was fine. yesterday a dozen times at least. It stalls but restarts itself (roll starting i guess) the water in fuel ,CEL and wait to start lights come on and then go off. We started with fuel filter, have changed the cam position sensor (yes with ford part not part stores) and now have also changed the Injection pressure sensor (also with ford part) while it needed changed as it was leaking oil the truck is Still stalling.
My dad is a technician He hooked his computer to the truck.. nothing. He was able to get the truck to recreate the problem with the scanner hooked up. When it stalls if he holds the throttle down the truck stays at an idle and the CEL, wait to start and water in fuel lights are on. It decelerates and puts along as nice as you please with the fuel peddle to the floor! let off the accelerator, lights go off and it recognizes the throttle again. No codes at all. hes thinking its the pcm telling the icp to shut off fuel. What would cause it to do that?
View 9 Replies
