I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 RepliesI just started having an issue on my 01 7.3 f350 with 203k miles, it will crank much longer then normal to start. If you shut it off then try to restart right away it starts normal, if you wait 10 minutes long crank again. if you shut it off and turn key back on but don't start it you can wait an hour then start right away. IDM bad? Vacation in 2 weeks and I would like to get this fixed first.
View 14 RepliesI have a 2000 F350 7.3 ... A couple weeks ago I noticed that it was taking longer to start then it should be. Now I have to cycle the key switch 3 or 4 time to get it to start. There is a clicking coming from the relay block under the radio. Sometimes the truck will start sometimes it has to be rolled off. I have recently replace the starter and alternator. I have had the batteries tested and they are good. I replaced the two small relays in the block under the radio, one is for the fuel pump and the other I understand is for the door locks? I also read on here the large blue one is for the turn signal so I have not changed that one. After all this I still have the same problems.
View 9 RepliesNew to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
i have a 2001 f250 7.3L PSD. it turns over but will not run. replaced the CPS , starter and the #30 fuse. IPR is new and all injectors are new, new gaskets and harness and new glow plugs new batteries. still just cranks and cranks. no oil pressure build up and no tach movement, oil level is good in HPOP. What could it be?
View 14 RepliesI purchased this unit, non running, was told the HPOP was bad, after going through the unit top to bottom, Im stumped, below is a list of items serviced and or replaced with OEM parts.
0. changed oil and oil filter
1. Terminator 500 Hpop
2. New ICP
3. New HPOP lines.
4. New starter and solenoid
5. Serviced Turbo (rebuilt with new parts and WW wheel)
6. Serviced Injectors (shimmed) all test good.
7. new pass and driver harness, UVHC replaced, glow plugs replaced.
8. new heavy duty GPR
9. Tested IDM no issues.
10. Hutch mod on tank (re-circulator was stopped up) deleted it, added inline filter.
11. serviced fuel bowl with new parts, upgraded parts on fuel bowl new blow off valve, new drain valve, tested heater all good no blown fuses.
12 replaced faulty fuel pump
Might be leaving something out of this list, the truck has run but only for very short periods of time, (hence the dropping of the fuel tank)
fuel pressure at 70 psi, some white smoke, connected to on board computer, checked every conceivable possibility No DTC codes, my gut tells me it has to be fuel related but at this point I just have run out of things to check.
I have tested everything with a fluke multimeter, including the IDM and all the circuits to the 42 as well as all the way to the injectors and glow plugs and find nothing wrong all tests yield valid readings,
There may be other information available but my after market scanner does not show any issue, KOEO buzz test results good.
The three times I have had this unit running it was dumping lots of white smoke, however after the last round of dropping the fuel tank and replacing the fuel pump the white smoke has dropped to a minimum, but cannot get the truck to run, cranks, wants to start, almost starts, got it up to 800 RPM last try but just will not go beyond that point.
I cannot find anything wrong, must be something I am either missing or its something my cheap scanner can't pick up on.
I have a 2001 Excursion 7.3 Diesel that is having a starting issue. Have replaced the batteries, has new glow plugs, common failing cam position sensor replaced once already. It runs great when it starts, no codes. It will crank, but not turn over at random times. Will do this for 3 or 4 tries...charge the batteries, go back later to start and it will on the second try. Turn it off, try again..and back to cranking, but not starting. Not fun having to worry about being stranded somewhere. Absolutely desperate at this point.
View 4 RepliesI have been having problems with my truck for about 6 months now. It start in Sept when my fuel pump went. I got a new pump and went to change it just to have the back clip break off. I fixed the line after getting 2nd degree burns from the boiling water I had to use to expand the line and installed the new fuel pump. Didn't fix anything.
At this point is was dropping below freezing every night ( I live in Canada in the mountains) so I thought it might be my plug relay again... changed that. After that my started has always missed so I figured I would change it out and sure enough the power bolt on the starter was broken. Changed it.
Then it started smoking and I read up on the quarter trick so I figured why not try that. I checked everything and they all checked fine but I am a glutton for punishment and figured I would do that valve cover gasket. So opened it up to find one of my glow plug wires on my harness was burnt up. I have a spare truck for parts so I grabbed the wire and replaced it. Still no change.
Today it was spitting out the usually raw diesel that I have gotten use to but when I was opening the gate to get a manlift for work I smelt oil just to find my turbo coved and the V had a small pool of oil happening there. I added 4L of oil and tightened up my valve cover back bolt on the passenger side... it may have fixed the leak but didn't have time to check.
I backed up to the manlift and it lagged a bit so I gave it a pump of the peddle and it died. Now it won't start. Charged batteries and tried after it cooled down but still no go.
In short my truck has been smoking for about 4 months now. It shutters at low RPM and stalls at the bottom of hills if I gear down on the hill (we have really steep hills around here). I have changed my oil three times in the last 6 months but it keeps coming out black (which it always has). No water in fuel or oil. Once and awhile it had problems starting when it was warm but after bellowing out massive amounts of smoke it would start. The truck turns over but wont start. There is no power where it died so I have to come home and charge the batteries every time they get low but even after it cooled down it still wouldn't start.
I went on deployment and handed the wife to crank the truck up she did but didn't drive it so batteries didn't charge back up. I got them charged up and the truck cranked right up. I was plugging it in at night and it would start just fine the next morning. Then a week later batteries kept dying in a few hours during the day. Had to jump it again. then even when plugged in trying to crank it there was a buzzing noise and it would crank but not start. I bought new batteries and it cranked right up and drove fine until I shut it off and same problem and batteries were low again and it will crank but wont turn over. I am thinking maybe alternator.
View 3 RepliesI've developed a problem, usually when starting, that the truck will crank over, start and idle for a few seconds and then shut off. The few seconds it idles it doesn't get any throttle input. I'll crank it back over taking a little more than usual to get it started. When it does start it seems slightly sluggish but that quickly, like almost immediately goes away and the throttle is working again.
Oh, 2001, 7.3 stock w/200k
I have an issue with my 2001 f350 7.3 PSD. Intermittently it will not start. It will crank really quick, but will not even try to start. I think it is not getting fuel. There are no CEL codes and I have a WTS light and the tach is moving while cranking. I hear a clicking/buzzing sound coming from under te center opf the dash. When I hear that sound it will not start. checked fuses and relays and it started before. not sure if removing the fue made whatever reset. this has happened a couple times. Now it will not reset. When I remove the number #24 fuse under the hood, the clicking stops. when i crank it, but still doesn't start. When it starts in runs perfect. Drained the batteries trying to trouble shoot, but have them charger now.
View 14 RepliesMy 2001 7.3 in a f350 automatic has this problem. I tried to start in am, no wait to start light comes on, but the od/off on auto transmission handle is blinking on and off. Turn key off and back on, no blinking, instrument cluster lights up as normal but no wait to start light, engine turns over as normal but no start or attempt to start, engine has about 56000. replaced glow plug relay, still nothing.
View 4 RepliesI've done everything I can think of, ive replace the starter, batteries and altenator, both batteries have at least 12.30 volts when taken out and checked, but i turn the key and it will have power then try to start and whole system dies and wont come back on, I've cleaned the terminals and posts to shiny and the ground connections but its still not getting power.
View 1 RepliesI have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 Replies2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
I have a 99 f350 Ford 7.3 service truck. It will crank and run but when it gets to 150 or 180 degrees it shuts off and will not crank back until it cools off. I have change the ECM I have change the IDM still same thing it runs till gets hot and then it cuts off. I have changed IPR valve IPC sensor .check the high pressure oil pressure it is around 800 900 at an idle it is around that pressure but when first starts up it is higher once it starts and runs it idles around that pressure 800 900 psi....
I have hooked up my scanner and it shows around 150 degrees oil temperature it shuts off . The high pressure oil stays the same as it was when you first crank it the low pressure crankcase oil is 60 psi ... Once the oil temperature reaches around 150 ~160 degrees the engine will shut off . Once you let it sit overnight or for several hours it might crank up ....
I have looked through a ton of threads to see if I can find one similar to my problem but have not. I have stock setup but had a dealer installed anti-theft device. The first time it would not crank, it was like the the anti-theft plug was missing so I checked out the key, tried the spare and finally removed it all together. I checked all the fuses and swapped the Starter relay for another of the same part number.
I later sifted it into neutral assuming it was the P/N Switch and it started. This continued intermittent for several days but then Neutral wouldn't work. I got under the truck and pushed on the actuator rod for the transmission and it started again for a few days. If finally failed again and I had time to buy a replacement switch.
Once installed I verified I had back up lights in reverse but still no crank. I have since pulled off the starter and had it verified as good. Is there more to setting/adjusting the neutral switch or is there something I am missing before I tow it in?
I recently (in the last few months) have noticed my truck (1999 F350 duallie) seeming to be running very rich … I pull a 32' trailer with it and noticed on the art few trips the front and right side of the trailer covered with diesel fuel spots when I got home …. It also smells very rich when idling…. The last couple times I started it in the mornings it seems to crank a very long time before it starts …it still runs but its got issues evidently … it has these 3 codes :
P1280
P0475
P1670
The 1670 will clear , but the other 2 I can't clear, they are right back every time you turn the key on …
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 Replies I got a 2000 7.3l with 400,000 miles on it that decided to just not start anymore after I parked it for a couple days. Its always been a hard starter due to needing glow plugs but I can deal with that. it doesn't even try to fire anymore. I replaced the CPS (my tack bounces when cranking). The ICP has oil in the plug so I just unplugged it for now till I replace it.
I pulled the IPR and cleaned it really good and bench tested it with 12 volts and could here it clicking so I put it back in. I can get under the drivers door with the key on and hear the fuel pump running. I gain oil pressure on my dash gauge when cranking. I check all my fuses. my WTS light comes on . I just don't have any fancy scan tools to make this easier. Also just cause I was feeling lucky I just went out and bought 2 new batteries for it yesterday so we are good there.
I have a 1997 F350 7.3 with standard xmission. Have not messed with it since Oct of last year. Then it would crank but no start. Now when I turn the key there is no wts or nothing the gauges move, and tach moves when cranking, but nothing else.
The cam and crank pos sensors have been changed. The high pressure sensors changed. Now when I hook it to the AE it says cannot connect to truck. Where I need to start? Have checked all fuses that I know about.