Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - 4r100 Transmission - No Reverse
Jun 23, 2015
my parents have a f350 which now has no reverse. it has a reman sticker on it, 230k on the truck but no idea on mileage on the tranny. shifts 1st through 4th fine, no slip. Tc lockup works just fine. No codes found with my solus scanner. When shifted in reverse it will move back about 2 ft if revved above 2k and then nothing. Am I looking a trans rebuild or is there something I can check and repair with in it the truck?
View 4 Replies
Advertisement
I don't know why... It seems its the 4R100 tranny non pto of course and 2wd version. I drove down the rd. after bleeding the brakes, new caliper front right, came home let it idle for about 10 min, shut her down. Went to move it about an hour later, it went into reverse no problemo, then when put it in Drive it revved like it was in neutral.
There was no banging, no clunkin, nothing to make it seem like something catastrophic happened. I then did a line pressure test and Reverse was fine 200 psi for sure, in drive mode however it was low like around 50 but had to rev real high to get it to 150 like 3/4 pedal and it would want to seem to go forward at a crawl but nothing more.
Next I did the obvious and checked the fluid, it was about 1/4 quart low so added a bit. The fluid did not stink and was beautiful red like new. I then tried again... no dice same scenario. Then took off the pan, no metal chunks and virtually no dust on the magnet??? ok so I figure maybe something with the shift valves? Took them all off and the accumulators as well, all check in place and all valves moved freely.
Now onto the the solenoid pack, checked all per manual for ohms and all were perfect reads at about 27 Ohms, except the EPC solenoid that is the big one on the pack, it should read about 3-5 ohms but this guy is about 12.5 ohms.
I spoke to a tranny shop in town and they said it would not be the EPC and that I could "unplug" the solenoid pack and It would still move forward without it but not to drive like this as line pressure would skyrocket?
I am on a tight budget and working on my back. I am willing to take the tranny out and bring it into town. Personally I think it's electronic but I don't know ...
Why THis thing would have 200 lbs pressure for reverse and so little for forward I mean? that should mean that the pump is working great, if there was a broken something metal I figured I would hear something rubbing or banging or see some shavings?
Can this be a "worn out" valve? or gasket issue? I really want to avoid removing the tranny at all costs so if there is something I am missing let me know and if you think just yank it out I will.
View 3 Replies
Installed rebuilt transmission 1 month ago. Have noticed reverse has started to go away. Feels like it is slipping or tires are losing traction with a lot of vibration in the steering wheel.(tires are not slipping that's just the way it feels).. Does it worse when trans is up to temp. I suspect feed bolts but want opinions.(Mark K.) All forward gears seem fine with no issues. I have never been under the pan deep enough to access the feed bolts.
View 3 Replies
I have a 2001 F350 4x4. My transmission went out a while back. It would only go in reverse. I had it rebuilt and it is still having issues. When I take off with speed from a dead stop it shifts late...about 3000 RPMs. It shifts fine until it shifts into overdrive. It will go into to 4th then right into overdrive causing the truck to act sluggish.
I'm looking into my truck not starting well at any temp too! I didn't know if it could all be connected some how. My mechanic said that when he first started my truck it had a MAP sensor code. He also said that when he unplugged that sensor it didn't change the way the truck ran..Still like crap. I have changed all glow plugs relays and even did the mod to it.
View 6 Replies
I have a 2000 Ford Excursion 4x4 7.3 with 230K miles, around 15,000 miles ago I replaced the transmission with a rebuilt 4R100, lately I have noticed a leak towards the back end where the transmission and the transfer case connects. Some of the bolts on the bottom of the pan have ATF on them, some others however do not. I have had to add a quart of ATF in the past couple of days in order for it to engage into drive when going from Park to Drive. I have to rev it before it actually kicks in. I'm hoping the leak is just being caused by a gasket either in the pan or connecting the trans to the transfer case..
View 7 Replies
I bought it 4 years ago with 205K, swapped trans fluid.. 10k miles later (I don't drive it a lot ). I am throwing the code P0750 Shift A malfunction.. i figured id swap the solenoid pack since I am pretty handy and it was affordable.. but it didn't seem to do the trick.. it drove around the block good for 5 minutes before it started shifting weird and throwing a code again.. almost seems to be slipping... I still have to check fluid level again and scan the code again but any suggestions? I have an apt to go to the tranny shop this week and would like to avoid the big bucks if possible.
View 14 Replies
I have the 4r100 transmission how do I bypass the safety switch? Also what are your thoughts on starting the engine with the transmission out? I know to bolt the spacer plate to the engine.
View 7 Replies
Problems with my 2001 F250 4r100 transmission. Transmission will only shift to 2nd gear when throttle is feathered at @2500 rpm. All other gears shift perfectly. This problem is consistent.
View 10 Replies
I have a 4r100 on in a 99 7.3 4x4. The shifting problem I have appears to be intermittant. it seems loose after warm up especially at the 4th shift overdrive and passing gear. possibly due to low presures ? sometimes (lately more often than not) hunts back and forth between 4th and o.d when passing or hill climbing. Under normal driving it shifts somewhat firm with 4th being an exeption.I have changed my crank position sensor filters and fluids which had turned dark and improved slightly. When I pulled the pan and replaced the filter the pan was spotless. No residue or signs of plates or debris. There is about 100,000 miles on the tranny and 350,000 on the truck. Questions: Is there a tcm for this transmission and if so could it cause these problems? I'm considering a purchase of an unlocked 1705 superchip to change the shifting but unsure if this will work for my issues...
View 14 Replies
I will start off with saying I am posting this for my dad. His truck is a 1999 F350 crew cab DRW 4x4 auto 7.3 with about 189K miles on it. He is leaving wednesday on a cross country road trip pulling a 40FT 5th wheel (no idea the weight but the thing is huge). He has glowshift gauges installed, one of which is the trans temp gauge. I believe the transmissions on these are 4R100, but I am not positive about that, but I'm sure many people here will know. He just told me that he had the mechanic he goes to replace the pan gasket on the transmission because it leaked quite a bit, just as a precaution. He also had them replace the brake booster as it was leaking inside by the brake pedal. When he got it back, he said he was driving it, and the temperature started going up to I believe 220 degrees not pulling anything. He said since he installed the gauges it has been between 180-190, and it jumped to 220.
What this could be. I have read that the TFT sensor can cause this issue, but it would throw a code and possibly go into limp mode. He has no check engine light and it was driving just fine. So the temperature is just all of a sudden high. Fluid level is fine, was checked after about an hour of driving, is red, and doesn't smell bad. I am suspecting the temperature isn't actually hotter, so there is another issue. It's only a big deal now because in a few days he will be dragging a huge 5th wheel behind him.
Last year, we towed some pile of crap 5th wheel down to our city for somebody with his truck, and we had to pull over halfway back because it started to smell like something burning. We think it was the trailer, as the brakes were questionable on them. When we got it to the people we were delivering it to, when we left, it wouldn't shift passed 2nd gear. He only lived a few miles from there, so he drove it home, parked it, then went out the next day and it was fine. He had the fluid flushed later and that issue hasn't come back since. No other work was performed on it since the pan gasket a few days ago. I am not sure if they are related being a year apart, but figured I'd mention it anyways.
View 12 Replies
2002 F 350 7.3 4x4
Aftermarket gauge will climb to 250 after around town driving of an hour or so or multiple trips within the hour. Not towing. 160,000 miles on odometer. Changed trans fluid at 40,000 mile intervals. Most recently about 1500 miles ago. Most recent change using Mark K's method. Was getting fluid from rear port when I changed fluid. Blew out oil cooler and there did not seem to be a blockage as flow was sufficient.
Still overheating according to autometer trans gauge in test port. No codes retrieved using auto-ingenuity also O/ D light is not flashing. Would like to run torque converter slip test using AE according to wooden things method but TC slip desired and transmission gear ratio is not available under that name in live data meter. AE just updated to most recent version.
I purchased a new tranny oil bypass and will install soon. Also purchased a new 6.0 cooler to replace stocker but am hesitant to install if tranny is failing because I am concerned that the new cooler will just get some blockage from a potentially failing transmission and I will be buying a new cooler along with a BTS rebuild.
View 14 Replies
I have a 02 f350 4x4 6 SPD one of my transmission lines has went bad is there anywhere that sales them.
View 1 Replies
I just bought a 2001 F350 diesel with 120k miles on it a couple weeks ago. Friday I headed out to Oregon with my 16 foot enclosed trailer filled with jet skis (about 4-5k pounds) for a competition. A few minutes after being on the freeway I noticed the truck did not have good power. About 30 min later while climbing a steep grade the truck almost went dead.
I started at 60mph and by the time I got to the top i was at 15mph with the throttle pinned. the motor sounded funny and shook the truck more then normal. After wards on the down side of the grade the truck started to act normal. I took it to my buddies house and switched trucks because I didn't trust if for the 13 hour drive.
Today I talked to a mechanic at the dealership and he said that it sounded like injector o-rings to him. I went home, pulled the valve covers and started the motor to see if anything is leaking. steam was coming from the valve area and the down spouts on the injectors was flowing oil. The thing that looked especially abnormal was one of the injectors looked like fuel was dribbling from it. I don't know if that is a problem or not. I couldn't tell if it was fuel or oil but no other injectors had fluid coming out near the wire connections.
View 14 Replies
2001 F350 just rebuilt the turbo, did the EBPV delete now no power.
View 5 Replies
The other day I had been driving about 3 hours and truck went dead then back on, it happened two more times in about 30 minutes.
(2001 F 350 Dually 7.3 A/T 2 wd.)
View 4 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
I have a 2001 F350 7.3 the truck will at random times loose power and almost shut down. A while back I had an issue with the uvch plugs and changed that out. Truck ran fine till I got some dirty fuel from a diesel tank at my friends farm. I did the hutch mod cleaned the tank and now have a frame mounted screw on filter before the pump. I cleaned the fuel bowl and changed the filter. Fuel pressure stays at 59psi and drops to 56psi wot. The truck is tuned with an edge programmer. After these mods the truck ran awesome for over 2000 miles. Now it has the above stated problem. I have fuel and hpop guages along with egt and boost. During the problem egts will increase rapidly and it seems like it is starving for fuel.
Hpop gauge reads 3300psi or above during wot and shows good pressure during these mishaps. I have auto Enginuity and I get a different reading at wot of only 2600 psi. The hpop gauge is tapped into the icp sensor per instructions and has been installed this way for a while with no issues. The tune has been on the truck for over 40000 miles. The only thing that I can come up with is it will occasionally throw a p1211 under wot or pulling my Gooseneck Dump Trailer when loaded. However it acts up sometimes and doesn't throw the code. Sometimes you can shut it off and start it back up and it's fine other times it will last for the whole day. My only guess is low pressure from the hpop but I don't reflect this from my gauge only on AE at wot. Wouldn't a bad pump act up all the time? Am I correct to think it is just the ipr?
View 2 Replies
I have a 2001 F350 XLT with cloth seats. In 2003 I upgraded those seats to power seats.
- When I upgraded to power seats I did not run a new power wire. Since my 2001 was at least fused for power and heated seats I located the Power seat 30amp power wire.
- That wire is located on engine compartment fuse #15 (Circuit 5298 as I recall) and Dark Green. It comes through the firewall and runs down the drivers side kick panel along the floor and then intersects with the power and ground seat belt wires that ran under the seat.
- The ground wire was coiled and attached to a ground stud behind the drivers side kick panel.
About a month ago I had a mouse get in and chew my seat wiring to shreds. I built my own harness and am good to go there, however since I had these seats all apart I decided to replace the foam and add HEAT.
So that brings me to the specific question. In the engine compartment fuse box, there is a 30amp positive wire for Heated seats. My schematic says it is a 14 gauge wire RD/BK on circuit 1153.
Where in the heck is this wire? I have literally tore the dash apart looking for this wire.
- I have verified the following with my fluke continuity tester.
- It is not part of the four customer access wires that drop on the right side of the interior fuse panel.
- It is not part of the tow wire bundle.
- I have checked the bundle that the Dark Green Power seat wire is in and there are no RD/BK wires in that bundle. I also poked the other 2 14 gauge (Yellow/Blue) wires in that bundle and verified they are not them.
-I have checked the three wire bundles behind the passenger side glove box and was unable to locate.
- I have verified it is not stored behind the compartment below the cigarette lighter.
I am looking for info which wire I am talking about and knows where Ford stored them when not used by having the XLT Trim with cloth seats. Yes I am aware that I can run an additional wire with a 30 amp fuse to the batter, but I would prefer to use the system and fuse that was designed for this.
View 2 Replies
My one owner 2001 7.3l F350 w/ 265K miles died a few days ago at a traffic light. First time it has ever died on me other than a CPS. This dying was an almost instantaneous with no CEL light, unlike the CPS's hiccuping and dash light up. I put it in park and it started right back up like normal. I continued about my errands and made it home. I have since driven it two more times the same distance and it has not died.
What I have done on this truck the past year.
-Replaced ICP -3/14
-Rebuilt IPR and checked IPR plug -6/14
-Replaced fuel filter every 7500 miles and I am probably due another one of those now
-Replaced air filter - 4/15
-Cleaned out both the sensor and the exhaust back pressure tube
-replaced CPS w/ dark blue unit from RiffRaff in -8/14
-checked main harness over driver valve cover and placed a piece of heavy duty wire cover wrap where they touch the valve cover -8/14
UVWH replace in 2008
Have a new IPR and pigtail coming just because I wanted to eliminate a bad solenoid on it. I also have a Torque Pro w/ blue tooth adapter on an LG tablet that I have yet to set up....but am working on it Will the truck throw any codes if the CEL didn't light up?
View 14 Replies
I change my motor in my 01 f350 ccsb to a forged rod one from a 97. When I put the thing in my inexperience cause me to screw up my torque converter in turn ruining my transmission. So after a rebuild I put it back in and she fit like a glove. Ever since I put the engine in i get a vibration at idle.
After I realize I screwed up the torque converter I figured that was the cause of the vibration. But now I know the trans is in properly I still have this vibration I'm thinking it's the position of the motor. I installed new motor mounts when I put the motor in but they were quite a bit off from the original points on the cross member.
My only idea to rectify this was to reinstall the original ones and try to position the motor back where it was prior to the engine swap. Or should I be looking elsewhere?
View 10 Replies
I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 Replies
