Ford 7.3L Power Stroke (1999-2003) :: 2001 F250 Won't Start / Buzzing Noise And Would Crank
Feb 3, 2016
I went on deployment and handed the wife to crank the truck up she did but didn't drive it so batteries didn't charge back up. I got them charged up and the truck cranked right up. I was plugging it in at night and it would start just fine the next morning. Then a week later batteries kept dying in a few hours during the day. Had to jump it again. then even when plugged in trying to crank it there was a buzzing noise and it would crank but not start. I bought new batteries and it cranked right up and drove fine until I shut it off and same problem and batteries were low again and it will crank but wont turn over. I am thinking maybe alternator.
View 3 Replies
Advertisement
I have an electrical problem on my 2003 f250 7.3 diesel. Sometimes it starts and sometimes it doesn't (mostly doesn't). I have two new batteries in it and have cleaned the grounds at the batteries and at the engine. When I go to start the truck all the lights in the dashboard work and it dings at me but when i crank the key nothing. I wanted to see if i was getting power to the starter and when I put my multi-meter down on the ignition wire on the starter and put my ground lead on the chassis bolt it starts every time.....I'm thinking this should not happen?? Is that a bad ground or a short or something else?
View 14 Replies
My 2003 f250 6.0l just up and quit. It make a popping noise out of the intake when cranking. I am getting 1150 psi at the icp and ipr is at 62% which seems high to me. The FICM voltage seem fine unless the batteries are drained and I am getting FICM sync. I replaced the HPOP, ICP sensor and IPR about a year ago. I recently replaced the air conditioning compressor and power steering pump. I am at a bit of a loss. I did pull the IPR and everything looked fine.
View 14 Replies
2001 F-350, 7.3L,
Has done this off & on for a few years and am tired of it! Noise is kind of a buzzing that seems to come from the flasher/turn signal relay. It stops buzzing when you turn on a turn signal, activate the flashers, or lift up on the shifter arm(?). Had to drive home yesterday with the flashers on! So I see from researching that it may actually be the multi-funtion switch on the steering column. So I removed that, cleaned up all the contacts, and put it back on and the buzzing did not go away.
View 14 Replies
I have a 2001 f250 ext cab long bed 4x4 that I use as a feed pickup. I have had it for about a year now. one of the issues I have noticed since I bought it is the issue I am having with the flywheel/starter. Its very random like maybe I have a missing tooth or something on my fly wheel. but every so often when I would go to crank my truck over it would just make a little whirring sound and nothing happen ( like my starter gear isn't sliding out and engaging my fly wheel.
After looking through my inspection cover I noticed I had a little wear on the sides but no teeth to my knowledge broken or stripped off. I noticed my starter had one bold loose but other two perfectly tight. It was also covered in oil and dirt from my truck sweating horse power I decided to replace my starter and have my original ford starter rebuilt. I replaced it with a NEW oreillys starter. I noticed it cranked about 5 times as fast but again every 10-15 starts I am getting the same no start. any thing I am over looking?????
View 6 Replies
Okay, I am having issues with a 1999 F250 XLT 7.3 with diablo programmer. I have searched and searched and have tried everything we could think of and it is a no go. The truck will crank, hesitate to start, start and die, other times it will only crank and not run at all. We can make it stay running by hitting the accelerator. The only code we were getting was the cps code, but that is suspected to be because of the excessive cranking and no start times. Previous to this issue getting this serious it would stall randomly, at idle, going down the road at constant speed, slowing down, or accelerating. We now have code P0231.
Through this we have tried:
IDM
(loaner) ECM
removing Diablo
3 CPS
shaving down CPS
Shimming CPS
IPR
Fuel pump
relay
fuel pump fuse
View 3 Replies
i have a 2001 f250 7.3L PSD. it turns over but will not run. replaced the CPS , starter and the #30 fuse. IPR is new and all injectors are new, new gaskets and harness and new glow plugs new batteries. still just cranks and cranks. no oil pressure build up and no tach movement, oil level is good in HPOP. What could it be?
View 14 Replies
I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 Replies
I purchased this unit, non running, was told the HPOP was bad, after going through the unit top to bottom, Im stumped, below is a list of items serviced and or replaced with OEM parts.
0. changed oil and oil filter
1. Terminator 500 Hpop
2. New ICP
3. New HPOP lines.
4. New starter and solenoid
5. Serviced Turbo (rebuilt with new parts and WW wheel)
6. Serviced Injectors (shimmed) all test good.
7. new pass and driver harness, UVHC replaced, glow plugs replaced.
8. new heavy duty GPR
9. Tested IDM no issues.
10. Hutch mod on tank (re-circulator was stopped up) deleted it, added inline filter.
11. serviced fuel bowl with new parts, upgraded parts on fuel bowl new blow off valve, new drain valve, tested heater all good no blown fuses.
12 replaced faulty fuel pump
Might be leaving something out of this list, the truck has run but only for very short periods of time, (hence the dropping of the fuel tank)
fuel pressure at 70 psi, some white smoke, connected to on board computer, checked every conceivable possibility No DTC codes, my gut tells me it has to be fuel related but at this point I just have run out of things to check.
I have tested everything with a fluke multimeter, including the IDM and all the circuits to the 42 as well as all the way to the injectors and glow plugs and find nothing wrong all tests yield valid readings,
There may be other information available but my after market scanner does not show any issue, KOEO buzz test results good.
The three times I have had this unit running it was dumping lots of white smoke, however after the last round of dropping the fuel tank and replacing the fuel pump the white smoke has dropped to a minimum, but cannot get the truck to run, cranks, wants to start, almost starts, got it up to 800 RPM last try but just will not go beyond that point.
I cannot find anything wrong, must be something I am either missing or its something my cheap scanner can't pick up on.
View 7 Replies
I have a 2001 Excursion 7.3 Diesel that is having a starting issue. Have replaced the batteries, has new glow plugs, common failing cam position sensor replaced once already. It runs great when it starts, no codes. It will crank, but not turn over at random times. Will do this for 3 or 4 tries...charge the batteries, go back later to start and it will on the second try. Turn it off, try again..and back to cranking, but not starting. Not fun having to worry about being stranded somewhere. Absolutely desperate at this point.
View 4 Replies
I just started having an issue on my 01 7.3 f350 with 203k miles, it will crank much longer then normal to start. If you shut it off then try to restart right away it starts normal, if you wait 10 minutes long crank again. if you shut it off and turn key back on but don't start it you can wait an hour then start right away. IDM bad? Vacation in 2 weeks and I would like to get this fixed first.
View 14 Replies
I've developed a problem, usually when starting, that the truck will crank over, start and idle for a few seconds and then shut off. The few seconds it idles it doesn't get any throttle input. I'll crank it back over taking a little more than usual to get it started. When it does start it seems slightly sluggish but that quickly, like almost immediately goes away and the throttle is working again.
Oh, 2001, 7.3 stock w/200k
View 1 Replies
I have 2001 7.3 f250 ... I just got it about 2 months ago I drove it for maybe 2 week and it ran good the other morning I went out to start it and would not start and the way I was parked my low fuel light was on so I put 5 gallons of fuel in finally got it started sum how drove it for maybe 2 hrs parked it and wen we got back in to go it was done for hasn't started since its been down for a bout 2 weeks now I've replaced hpop, icp, pcm, fuel filter,checked idm for corrosion it all looks well, gpr,checked uvch on driver side looked good and changed cps what else do I have to go from ? No matter what it won't start good batteries cranks good but no start ...
View 14 Replies
2001 f250 7.3 with 210,000 miles. Was running rough when cold and glow plugs were bad so I bought new glow plugs and had injectors rebuilt with 100% over stock nozzles. When I changed them I made sure I turned the motor with glow plugs out and pulled the drain plug in the head. Wanted to start it just to get the oil out before I let it sit for a few days til I got the tuner. It started fine and I let it run while I ran in the house and when I came back out about 1 min later it was off. Didn't want to start again. Just left it til I got the tuner on and It still doesn't want to start. What I should check? Turns over good and has good batteries. Also it's a hydra chip tuner with beans tunes. Darren weeks rebuilt the injectors.
View 7 Replies
So I have a 2001 f250 7.3l and on my way to work yesterday while driving down a hill I switched my ts 6 switch to 140 and it immediately stalled, so I pulled over and restarted the truck and it started up fine and I drove the rest of the way to work, I go to start it after work and it won't start, it just cranks and cranks and cranks, occasionally it'll fire and I got it to start and was able to rev it for about 30 seconds but then it died, disconnect the 6 position switch from the idm and tried but still nothing.
So today I replaced the ipr valve, got everything back together still won't start maybe a little worse now, I know it's getting fuel cause there's pressure in the bowl when I try to take it off, there's a new icp valve, cps, new fuel filter and new sending unit, the hpop is topped off. Also I noticed when I went to change the ipr the wires on the plug were bare and touching so I addressed that, I don't know what else it could be?
View 14 Replies
Ok I've got an 01 F250 sd 7.3 with 257k on it it just started talking longer to start than it should it will do it cold or hot even if I shut it off at the drive thru takes it like 10 sec or more to fire. My question is I thought about purchasing a autoenginuity to find the problem but not sure the best place to get and what model I should get.
View 7 Replies
2001 F250 7.3 4x4 330000
So weird noise while breaking but only right at the very end of the breaking cycle or if breaking hard. As soon as you come of the breaks it stops. Changed out front rotors and pads last night thinking that was it but its not. I'm inclined to think it could be the driver rear side by having someone else drive and brake whilst stood by it - rear rotors and pads changed 18 months ago and quick visual check appears they are ok. Just can't work it out - any thoughts? Caliper seemed ok on the front left, but would probably need doing in the next 6 months
View 11 Replies
I have a 2001 F250 Super Duty V8 7.3 L. I removed the water-pump then waited five days for the oring for the new pump. I installed it and now the truck will not start. I have drained the fuel water separator and replaced the filter. On the passengers side through the kick panel I found that button popped out so I pushed it back in and still it will not run. It acts like its not getting fuel but if my fuel water separator is filing up I'm assuming mu fuel pump is working??
View 7 Replies
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 Replies
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 Replies
I am trying to diagnose an issue with my 2003 F-250 6.0L PSD.
The first time I crank it everyday, it struggles to start. Beyond that, it seems to run fine and not have issues cranking throughout the day.
I've recently replaced both batteries, the FICM, the fuel filters and the FI wiring harness. What could be the issue?
The video shows exactly what I deal with every morning.
YouTube - 2003 F-250 Cold Start Issue ....
View 14 Replies
