Ford 7.3L Power Stroke (1999-2003) :: 2001 - Dual Generator Upper And Lower Fault Codes?
Mar 26, 2016
I have a 2001 f350 7.3 diesel and want some info... I am switching out the air intake and thinking about the Banks package.. How does it can be compared? Also, I am dealing with an issue of a dual generator upper and lower fault codes.. I only have a single generator system and it is running strong as far as I can see.. When I start it shows 12.9 and then raises to 14 when running.. Stays there the entire run...
View 6 Replies
Advertisement
I have recently replaced both tie rod ends and found out when I took my truck for an alignment the mechanic stated that I had bad driver side ball joints (upper & lower) I confirmed this with SEARS and they stated that it was all the ball joints upper & lowers! the Haynes repair manual (1999-2010) states "ball joints on 1999 through 2013 2WD models were not replaceable".
View 4 Replies
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
View 8 Replies
Came on other day. No ses light or fault codes. What it means?
View 10 Replies
Running dual coolers? I just got a new transmission not too long ago and want it to last. Was looking at this mishimoto with fan. That way in the winter i can deactivate it and use it while towing or summer. Also the way I see it if I leave the stock cooler in place it's one less thing to mess with.
View 14 Replies
Have just about 1,600 miles on tuck born on 12/14/11. Love it, but.. When going slow in subdivision I am getting some hesitation/bucking when going in the upper 20s/lower 30s. When I feel it I look down and I am usually in 3rd. Is this the transmissible thing? When it happened Sunday it felt like it was going to die. If I start off with a quicker start (to get to highway speed) it shifts fine. It just started the last few weekends......
View 14 Replies
F350 2001.
Constantly throwing codes for both front wheel's ABS. Ohm'd out both sensors - same reading
Ohm'd out wires leading to sensors - same reading
Ohm'd out rear diff speed sensor against a new one - same reading.
Pulled front sensor's cleaned and put my fingers in the sensor hole. What should I be able to feel? I'm wondering if the previous owner put non ABS hubs on?
View 14 Replies
I purchased this unit, non running, was told the HPOP was bad, after going through the unit top to bottom, Im stumped, below is a list of items serviced and or replaced with OEM parts.
0. changed oil and oil filter
1. Terminator 500 Hpop
2. New ICP
3. New HPOP lines.
4. New starter and solenoid
5. Serviced Turbo (rebuilt with new parts and WW wheel)
6. Serviced Injectors (shimmed) all test good.
7. new pass and driver harness, UVHC replaced, glow plugs replaced.
8. new heavy duty GPR
9. Tested IDM no issues.
10. Hutch mod on tank (re-circulator was stopped up) deleted it, added inline filter.
11. serviced fuel bowl with new parts, upgraded parts on fuel bowl new blow off valve, new drain valve, tested heater all good no blown fuses.
12 replaced faulty fuel pump
Might be leaving something out of this list, the truck has run but only for very short periods of time, (hence the dropping of the fuel tank)
fuel pressure at 70 psi, some white smoke, connected to on board computer, checked every conceivable possibility No DTC codes, my gut tells me it has to be fuel related but at this point I just have run out of things to check.
I have tested everything with a fluke multimeter, including the IDM and all the circuits to the 42 as well as all the way to the injectors and glow plugs and find nothing wrong all tests yield valid readings,
There may be other information available but my after market scanner does not show any issue, KOEO buzz test results good.
The three times I have had this unit running it was dumping lots of white smoke, however after the last round of dropping the fuel tank and replacing the fuel pump the white smoke has dropped to a minimum, but cannot get the truck to run, cranks, wants to start, almost starts, got it up to 800 RPM last try but just will not go beyond that point.
I cannot find anything wrong, must be something I am either missing or its something my cheap scanner can't pick up on.
View 7 Replies
i bought a f250, i rebuilt the 7.3 after installing it the transmission isn't shifting correctly. Reverse perfect, 1st and shifts to 2nd great. wont go into 3rd. i replaced the 2 sensors on the transmission, i replaces the sensor on the 3rd member. the speedometer works but not correctly, i can unplug the sensor on the front of transmission and it shifts into 3rd. but when i plug it back it doesn't. no codes. could it be the ecm?
View 10 Replies
I've been battling this truck for over a month now and starting to go a little crazy, It's a 2001 f350 7.3L, with a "used" 7.3L engine from a 1997. Transferred all the necessary parts to make it happen. Keep getting the evil p1316 idm codes detected coming back upon start up. Anywhere between 5-30seconds after starting the left bank dies. I've gone threw and replaced the IDM with a reman unit. New valve cover gaskets (with new harness). even went the extra mile and put in a new power wire (for the driver side) running directly from the new valve cover into the IDM bypassing a connector above the left valve cover. All injectors are checking out around 3ohms. With glow plugs all around 1-2ohms. What's interesting about this is, I can disable any one of the injectors on the left bank (doesn't matter which one) and the engine runs great considering it's down on one cylinder. But when I hook up that last injector it will kill the whole left bank again.
View 13 Replies
Finally had a good scan done on my truck at the mechanics. The reoccurring codes were P0478 and P0470. It looks like a bad exhaust pressure control sensor. Looks like an easy fix.
View 14 Replies
Well I was fueling the truck today and I opened to hood to check it out and noticed that there was no pressure in the cooling system by squeezing the upper hose. I did have a spare degas bottle cap and removed the old one slowly and replaced. I have been driving over 30 minutes and it is close to 100 degrees.
I then drove on down the road, the truck is not getting hot. I stopped to look at some running boards and the truck was running and then I came home and still no pressure, the truck is still running, I removed the cap and no pressure, I then removed the small hose going to the top of the degas tank and no coolant came out. I turned the truck off and disconnected the upper hose and some coolant did come out.
Is this normal? The truck runs just fine, just has me worried. I just bought the truck and the previous owner recently replaced the water pump, T-stat, hoses, etc. All parts were bought at O'Reilly. So everything looks good.
View 3 Replies
I have a 2000 7.3 I've been struggling to figure out why I do not have a lot of power below 2k rpm... The truck screws once it gets above 2k.
Assuming it was a turbo issue - I had the turbo rebuilt and put the wicked wheel in. Made a huge difference overall but truck still bogs under 2k.
No leaks in up pipes, they have been replaced recently. What the problem could be?
View 7 Replies
I'm going to be replacing my lower radiator hose so figured might as well switch over to the extended life stuff going to probably go with the Delo ELC.. Supposedly it's good for 750k.
View 14 Replies
So the other day I was driving my truck and all of the sudden it through a p1316 code. So I did a Buzz test with FORscan and it gave me this error P12777. For the people that have dealt with this code before, where should I start looking, As I have a lot of stuff to take out on the passenger side before I can even see the valve cover. Is it more of a wiring issues or is it a injector issue.
View 4 Replies
I just noticed today while driving to lunch today that at lower speed and tons I can here an intermittent hissing sound. But as I speed up and build boost it goes away. Not sure what could be causing this sound. it sounds like it could be some sort of pressure leak or exhaust leak I have no clue...
View 12 Replies
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 Replies
Connected my obd2 to my car and found 3 fault codes 1 which repeated itself twice.. the codes are P0453 that repeated itself a couple times and the 3rd one is P0133.. I looked them up and see that one can be either bad grounding and also a bad oxygen sensor? and then the other mentions something about fuel and says something about fuel pressure sensor?
View 3 Replies
Last couple of days I've been chasing a small oil leak. Finally figured out it's coming from one of the hoses connected to the lower part of the hpop (hpop hose). Leak is coming from the fitting connected to the lower part of hpop. Do I need to replace the whole hose and fitting? Just the fitting? is there a replaceable washer or oring?
View 10 Replies
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
View 2 Replies
I have a customer with a 2011 that has a ticking noise that developed into a engine miss with no fault codes. His mileage has dropped from 18 mpg to 14.5 . Heard the noise more pronounced in the left bank. Tonight I disassemble the engine and found the rocker arms by the pivot ball are showing signs of recent wear looks as if they had a die grinder taken to them. The rockers spear loose? The truck has over 100k on it.
View 6 Replies
