Ford 7.3L Power Stroke (1999-2003) :: 2001 - Clunk / Vibration In Rear End
Aug 1, 2016
I recently purchased a 2001 excursion 7.3 after driving it for a while I have noticed a significant clunk and vibrate in the rear end. I have read a lot of people saying it could be the slip yoke needing lube which I intend to do but most are saying that their clunk is at start and stop.
Mine is between 30 and 60mph when I let off the accelerator I get a clunk followed by a vibration and when I get on the accelerator it is just the clunk. Does this sound like the slip yoke to yall or am I looking at something more? I have tried turning the drive saft and there is no play in it at all.
View 14 Replies
Advertisement
I'm a mechanic but work only on cars so I'm a little shy on diagnosing trucks. I have a 2001 7.3 f250 4x4 short bed, when I give it gas I can hear a clunk, when I let off of the gas I also hear a clunk. Also when traveling at high way speeds I can feel a strong vibration when I very lightly give it gas but the vibration goes away as I give it more gas.
View 5 Replies
I change my motor in my 01 f350 ccsb to a forged rod one from a 97. When I put the thing in my inexperience cause me to screw up my torque converter in turn ruining my transmission. So after a rebuild I put it back in and she fit like a glove. Ever since I put the engine in i get a vibration at idle.
After I realize I screwed up the torque converter I figured that was the cause of the vibration. But now I know the trans is in properly I still have this vibration I'm thinking it's the position of the motor. I installed new motor mounts when I put the motor in but they were quite a bit off from the original points on the cross member.
My only idea to rectify this was to reinstall the original ones and try to position the motor back where it was prior to the engine swap. Or should I be looking elsewhere?
View 10 Replies
I have seen a number of post about front end vibs associated with steering and braking. I have had a hard time finding these posts and decide to post my vib/noise accompanied when brake and steering applied.
I too have a vib/noise coming from the front at low speed braking and turning (mostly parking lots and such).
About 5-6 months ago (around 90k miles) I noticed a high squeal at high rpms. I thought it had something to do with the belt so one day while driving up the grapevine pass (I-5), under high rpm, I turned the AC on. The squeal went away, I turn the AC off the squeal came back, I was pretty sure it was the belt and hopefully not the AC compressor.
10k miles later, I finally got to changing the serp belt. After I changed the belt, I immediately heard a rough vibration noise when braking and then when PS is under strain. It seams like it comes and goes when it wanted to, but now its always under the low speed parking lot conditions. Sometimes the vibration can be felt in the floorboards.
I haven't gotten to fix'n it yet lol... as I don't know what the problem is. I'm finding it hard to believe that a serp belt could be the cause of vib/noise when braking/low speed turning. One thing for sure, the vib/noise instantly occurred when I changed the serpentine belt. What might be going on here?
View 8 Replies
I'm looking at a 2001 Excursion with 242k miles. Truck is all stock, and everything checks out well. The only thing is there is a slight vibration at idle, that increases quite a bit when the engine is revved to about 12-1500rpm. Ran a CCT, and #8 was flagged. I know that can be somewhat normal depending on the CPS, right? Otherwise the truck is smooth, and in great shape. Should I be concerned about what feels like a slight miss on #8?
View 3 Replies
I picked up an '01 F-350 standard cab and bed plow truck for parts and am preparing to swap the rear axle into my E99 F-250 SB unless someone gives me good reason to just swap the carrier. I want the LS differential. I will also do hutch/harpoon on the tank so I figure that bed removal will make both jobs easier. Once I have both beds off I can give things a visual and see what lines and cables need to be changed out as well. I believe that there is a difference in the passenger's side caliper but I am not 100% on that and I don't know what I will need to change if anything. I am hoping that my drive shaft will remain.
Thus far I have gotten to rotted bed off of the donor truck. The bolts would not come out and I had misplaced my cutoff wheel so out came the torch. In the process of blowing the heads off of the bolts I also blew some holes in the bed but didn't care, it's scrap. Fortunately I did not blow any molten steel onto the fuel tank. I was able to lift the bed far enough to reach the light plugs in the rear and disconnect them without damaging them. The large one that is still attached to the frame goes to the trailer lights and could have stayed connected. The two smaller ones with ends up feed the tail lights and license plate lights, they have to be disconnected.
The bed is shot so I just hooked chains into the rear pockets and drug it off with the front end loader. I did have to get off a couple of times and unsnag it from the frame. Oops, and to cut off the fuel tank fill and vent hoses.
The bolts are extremely rusty and wouldn't budge so I cut them off.
The organ recipient has a spray on bed liner that I had to cut through to get to the bed bolts, the heads look like new and the bolts look like they will all come out for me.
And this is what the nuts and clips look like that mount the bed to the frame.
Yep, there is plenty of rust.
Also, I found two safety cables wrapped around the bed frame and main frame mid bed that will need to be disconnected before bed removal. These are on the E99 SB only, not on the '01 standard bed.
View 14 Replies
I noticed a clunk a while ago but could never pin point it and today its the worse it has ever been. I did some research on this and everyone is pointing towards sway bar bushings. now if that is the case why wouldn't they just replace the sway bar link? I see some do poly bushings and others regular rubber. What is the best way to go about this? and I also see you need a shop press so I'm lucky I have one.
View 6 Replies
I'll get right into it, when I put the mud grips on my truck it always had a little vibration from 42-45 mph and it wasn't to bad. Recently from 30-65 I have a bad shuddering vibration that I get mainly in the steering wheel but I also feel it everywhere else and can see it on the mirrors. Well the front sway bar has a bushing that is broken. But also I notice recently at low speeds from my rear drivers side tire there is a noise that isn't right, maybe a bad bearing? I have a long list of stuff I gotta do on the truck and I just want to stop the Shake so I can get to everything else.
View 14 Replies
As I'm cruising once I hit about 50mph I start getting a vibration in the peddles and floor board. It's not real bad but noticeable for sure. When I hit 70mph it's worse and the truck even sounds like it's vibrating. As soon as I let off the peddle and coast everything is golden.. Smooth.. So it seems to be a problem only under power..
A little back story : About a year ago I was getting bad vibration and loosing power. I put it in the shop and the mechanic said the filter or screen in the gas tank was clogged so he cleaned it. I went to Korea for a year so the truck sat in government storage for a year. When I got it back in March I put in back in the shop to have the front passenger side hub replaced.
I don't know if any of that has to do with the vibration I'm getting now.
Truck
2003 F250 ext cab
7.3l
179k miles
View 6 Replies
On my way home from work the other day my 2000 7.3l started making a humming sound while driving. I noticed that it was shifting harder and it began to slam into gear when I would take off from a stop. By the time I pulled into the driveway I had to be half way into the pedal to keep it moving. I shifted into reverse and it clunked loudly and didn't want to back up. I don't know much about transmissions but I'm thinking that it's probably shot. I'm hoping that it's something other than a complete rebuild but doubtful.
View 6 Replies
So I'm attempting to track down a grinding/vibration I'm getting only in 4x4. Mechanic checked the axle and front drive shaft u-joints and he said they're all fine. It's not the wheel bearing they are both fine, one is brand new. What to check next or how?
View 10 Replies
2001 7.3 auto with 188k miles. Supposed to have had a new tranny at 99k miles. Fluid nice and red with no smell.
Here's problem: during the 3rd shift (gear before overdrive), and between 40 and 50 mph, I get a small vibration in tranny. Seems to be just that shift. It's not noticeable if I run it a little harder on the shift (speed up). If I let it lag on the shift, the vibration is worst. All other gears seem ok.
Questions:
1. I believe I have a 4R100. It has a drain plug, but how do I confirm?
2. I have a couple different scan tools. Should I be getting codes if I have tranny problems? Or is there a scan PID I can check?
3. I was thinking of starting with fluid change. Since it probably hasn't been changed since 99k miles.
Last question: any detailed write on fluid change handy? That would include type of fluid, filter part number, etc?
View 8 Replies
I have a 2000 with a six speed and through the first 2 gears while giving it only a little throttle, worse on hills and worse while towing I have a pretty decent vibration. Once you get to 3rd and up its fine. I have read about axle wrap and due to the fact my springs are pretty wore out I think this is a big part of it. Any other things to look at other than new springs? The u joints all look and feel fine so I haven't touched them.
View 8 Replies
So I have my 2000 F250 in the shop because I was feeling a funny vibration in my brake pedal. (isn't warped rotors, I know what that feels like). It also felt like the brakes were on, then would release a little, lengthening my stopping distance.
I took it to a small local shop and the guy said it sounds like the hydroboost. I told them to fix it. Next day, before they start to fix, they call and say they can't guarantee it's the hydroboost and may be the Power Steering pump.
My question is; is there a way to test it to know for sure which part is failing? How do I figure out which one is causing the problem?
View 1 Replies
I have noticed a small vibration at 40-50 mph for a few weeks now and was unsure to the issue.. ( I just checked wheel bearing ect , last night ) . This morning at a stop light she started to white smoke shake and clack, somewhat violently, when I pull away from a stop it seems to smooth out and run normally.. A stuck injector ? Toast injector ?
View 11 Replies
I've got a 2002 F350 DRW 7.3 truck I'm having a little concern over. It started this summer, when under very heavy pulling I was getting a very noticeable vibration between 20 and 25 mph. I did not think much of it, as it only happened under extreme conditions.
Now I'm getting the vibration all the time, and it's started another band which is 40 to 45 mph. It's much worse if you are very light on the throttle, if you're full throttle it's much harder to notice.
Truck has 154,000 miles.
View 12 Replies
I have a 1999 f-250 super duty 7.3 .... Recently my truck has started making a humming noise when push the throttle and I can feel a slight vibration, the noise and vibration go away when I let off the throttle, I have changed all five u joints, both wheel bearings in the front, the steady bearing, changed tranny and both diff oils, put new brakes and calipers all around and pulled apart the hubs but I can't seem to find what's causing it. What it could be or what I could check? It has an 8 inch lift and is sitting on 37's and some performance upgrades, could any of that cause this ?
View 9 Replies
I have an 02 F350 7.3 6 speed with only 86,000 miles on it ... Ive owned the truck about a year and a half now and ever since i can remember the transmission has had this growling/Groaning/Vibration sounding noise when ever Im in 1st or 2nd slow rolling with barely any throttle. Itll make the noise going slow and as soon as i let out on the clutch and start moving, but once i give it a little more throttle and start moving at a more proper speed for the gear, the noise fades away ... Id assume its just the transmission making noise due to the low speed and RPM when slow rolling or just starting from a stop.
View 8 Replies
Recently I have a vibration that I can feel slightly through the steering wheel. If I'm driving down the highway doing 70mph + I have a noise coming from the front end. Also while driving let's say 40mph and below and I let off the pedal to slow down I can here a vibration in the front that kind of sounds like a small Jake break. And when going over anything bumpy I hear like a popping metal sound. This popping sound has been going on for a long time and still can't figure it out. I replaced all my shocks thinking my old set was bottoming out. Nope, still have the same problem.
I jacked up the front end yesterday and checked for movement top and bottom and side to side thinking maybe the wheel bearings or ball joints were going. Everything is solid. Spun the wheels and no noise, no grinding, nothing. I can't figure it out. I have not removed the wheels to check and see if a caliper is loose. I will be checking that next. I did notice while looking around that I can push up on my pitman arm on the steering box. It's not a huge amount of movement but I can still move it. I can also see teeth marks between the box and the arm, not sure if that is normal or not. When I do move it up and down it sounds a lot like that metal popping sound I have been hearing. So, I know this is a lot.
View 14 Replies
I recently had a flat tire - Schwabs fixed it. Then told me my rear brakes were bad so I replaced them. I noticed when coming to a stop the last 20-30 feet you can really feel the front end vibrate - almost like it is in 4wd but it is not. I checked the hubs and they are on auto and lifted the truck to spin the wheels and made sure everything was dis-engaged. My front rotors were bad so I replaced them and the pads thinking it was the root cause. I also greased the front wheel bearings using the little tool from riffraff diesel where you take out the speed sensor and insert grease.
View 10 Replies
A little about my truck. E99 F-350 crew cab long bed dually 4x4 223K miles. 4.10 gears with LS in rear.
I bought the truck June 2016. I ended up wrecking the truck on the test drive. Thought it was a 4 way stop and pulled out in front of a lady and she ran into the passenger side tire. Only damage that was on the truck was a busted tire, and the fender smashed in. Some how missed the door and the bumper.
I replaced all the front end: u-joints, ball joints, steering linkage, brakes, rotors, calipers, and all the u-joints in both of the drive shafts, also changed the fluid in both axles.
I have started to notice a slight "vibration" "shimmy" while driving down the road. Mainly while in a curve or changing lanes; applying pressure to the steering wheel one or the other. Tires have been balanced, and rotated several different times now with no luck at all.
While backing up, I can feel something "popping" "clunking" especially while turning. Like backing out of a parking space.
Insert troubleshooting:
Jack truck up and put on jack stands.
- Pull and shake all tires. --No movement
- Put in drive and watch all the rear end. --Nothing shaking or out of sync.
- Put truck in 4wd, hard to engage, watch front end. --Nothing shaking or out of sync.
- Turn tires to full lock. --Drive line starts clanking and shaking and rear tires acting funny.
- Turn tires straight. --Problem goes away.
- Put truck back in 2wd. --No problems when turning wheel lock to lock.
- Drive to empty parking lot. --Mainly feel problem while backing up, really have to feel for it. Most people call me insane.
- Lock the front axle. --No difference.
- Put in 4wd. Drive straight --No difference.
- In 4wd while turning. --Truck wants to act like it is fully locked in the rear and will bind up and slip a tire. You really have to give it some fuel to make it even try to move, and its almost like the truck wants to fold in half on itself. Cant keep the steering wheel in one spot as it keeps "jumping" on me.
- Put in 2wd. --Acts the same way until the truck fully comes out of 4wd then smooths back out to where you have to really feel for it. 4wd light stays on forever, before going off later in life.
- Put in 4low. --Gears grind and will not engage.
Would this indicate that the transfer case is messing up on me? Why would the rear axle feel like it is locked when in 4wd?
View 2 Replies