I have a 2000 Ford E350 Short Bus 7.3 It has abs in the rear diff. I have changed the sensor. I have connected my AE but get nothing at all from the sensor. My speedometer does work. My overdrive light flashes and the transmission does shift properly. I plan on looking for a bad ground. Can I test the wiring using a volt meter
View 2 RepliesHere is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 RepliesI am having an overcharging issue with my 2000 F350 diesel. It first started when I had a garage check the batteries due to poor starting this winter. They found one reading 6V and I had them replace it. After that the battery light came on. So I had them check it out again and they replaced the other battery. I can't remember if it started before or after the second battery but it started overcharging 16-17 volts according to the dash. I replaced the alternator still overcharging. Since then I have run a 4ga ground from one battery to the alternator and a 4ga ground wire from the other battery to the cab. I also checked most of the stock ground wires which all seem fine. Lastly, I also bought a ford alternator pigtail because one of the wires had cracked insulation and some corrosion. Currently it overcharges unless the battery light comes on which once it does the voltmeter in dash reads normal.
View 14 Replies Auto trans. The Overdrive light flashes on the Selector lever. Never stops.I put tape over it because it is annoying. Especially at night. It goes into overdrive no problem.
A Couple of times it did not flash and was stuck in first till I manually shifted. Then the light started flashing again and works normal. What now......RPM Sensor?
I have a sensor on the top of the engine on the driver side that has oil coming out of it. I think it is called an IPC but I want to make sure before I go buy a new one. It sits right behind the power Steering pump. I am replacing the Power steering pump and hoses so I thought I would replace that as well. Also since there is oil in the connection what is the best way to clean the connection electric parts cleaner? By the way this is a 2000 7.3 4x4 ....
View 11 RepliesI am still failing to appropriately diagnose the problem(s) with my '03 Ford E-350 7.3L Powerstroke. This van has only 69,000 miles on it. A week or two back (just a few days back in work time) it suddenly went from running perfectly smooth, clean and wonderful to this:
- Zero power. Putting the van in gear and flooring the engine causes lots more smoke not nearly any rev of the engine and just a crawl forward.
- Lots of smoke out the back exhaust, whitish. I cannot discern wether it smells like diesel or oil (because I'm ignorant here), but the smell is very strong.
- After warming up and idling ~ 15 min I check under the coolant cap and see no signs of bubbling or disruption (from opening the cap in the coolant tank).
- After warming up there are no warning lights visible on the dash, and I don't have a computer to read codes (if there are any to read).
- I replaced the turbo up-pipes which had a visible leak previously. This did not hurt the symptoms, though no more visual leaks under the dog house.
- I thought maybe I put gasoline instead of diesel in the truck, not so.
- To do the above test I had to use the fuel pump to get gas out the tank to test. I hijacked the fuel pump output and turned the car on a few times to get gas out to a tank. The pump seemed to work just fine.
This was all very sudden which is perplexing, and, in use, the van was previously an ambulette and in my few miles with it (maybe 200-300 only) use was extremely light for such an engine/van, just driving around doing errands. I am not sure if this is relevant (no one has suggested so, yet) but before all this happened I uninstalled the rear HVAC that came with the van when I bought it. The AC lines were sealed under the hood. The coolant line was returned at the doghouse (you can see this at the beginning of the video).
At the moment the van has no power to go anywhere. I have not yet checked the CPS or IPC sensors, and understand this might be the next route in standard troubleshooting?
2003 Ford E 350 7.3L Trouble - YouTube....
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
I have a 1999 Ford e350 7.3 powerstroke with 140000KMs on it.
The truck cranks really well but it just wont fire off, not even with a shot of starting fluid.
I recently changed all 8 glow plugs, fuel filter, fuel, oil and I keep it plugged in, my last mechanic told me the engine is toast and it cant be fixed.
I have a 99 Ford e350 7.3 Powerstroke with about 150000KMS on the clock. However I am having a really hard time starting it in the Cold Canadian Winter (-30). Last week I changed all 8 glowplugs, the batteries, the oil, fuel, fuel filter and yes i always keep it plugged in.
It cranks really well, but it just wont fire not even with a shot of start fluid. I don't know anything about these trucks much less a diesel engine. A guy took a look at it and said my engine needs to b replaced. (I think he is wrong)....
I have a 2001 E-350 with 7.3 that will not start on its own. It is showing only 80psi ICP while cranking. It started with the aid of some starting fluid it will run at 550 psi ICP but the ICP duty cycle is running over 20%. We started with less than 10 psi while cranking and after a new IPR was installed it's now at 80 psi while cranking. There is good battery voltage oil is at correct level the HPOP is full. I just don't know what to look at next.
View 6 RepliesOne of my batteries on my van is on the frame rail. The box rusted out so I routed the battery into the back of the van for now. The van wouldn't start because the batteries were low. I charged the battery in the front engine bay overnight but it did not charge the 2nd battery, does that mean there's a disconnect between the two batteries? I thought they were in parallel.
View 2 RepliesI have a 2001 E-350 w/7.3. When I start the truck first thing or when engine is cooled down it starts fine. I checked the high pressure pump pressure and it is 500 - 600 psi start up great. But when engine warms and try to start it it has long crank before starting. I checked pressure and it is between 425 to0 450 and takes awhile for it to get to 500 or better. Is this a cause of the high pressure oil pump ? I changed the oil and still does same thing. Also I noticed that after engine is hot and I try to start it, while cranking the engine the oil gauge does not move. I don't know if it supposed to when you crank it or not. I thought on other 7.3's I've worked on that the gauge builds up pressure....
View 14 RepliesI recently purchased a used 2001 E350 with a 7.3L and the transmission is not shifting properly. It will go into Reverse no problem, put it in "D" and it starts in high gear and will not shift out. If I manually shift from 1 to 2 to "D" it works fine and will even go into OD. It will not down shift on its own either. What should I do to fix this issue?
View 2 Replies2002 e350 7.3 diesel transmission... At 7 miles the speedo began bouncing and truck drops into second. Parked it 30 minutes, stated up no problem until 8 miles and the it started again. Have checked most of the electrical, changed speed sensor and transmission position sensor. Only error code 2-3 rd gear mismatch.
View 11 RepliesSo a dead thermostat forced me to drain the coolant in my E350 7.3L. I noticed the previous owner had green coolant in the van so I decided to do a flush and put in the right coolant. I used Shell Rotella ELC. Well, I noticed after coming home the other day that the van was leaking coolant, upon inspection I noticed its now leaking from the water pump, then today the drain valve sprang a leak! What the HECK is going on!? Is it possible that the seals were shocked when I changed the coolant? Not looking forward to doing a water pump replacement on an E350... sure is crammed under the hood.
View 9 RepliesWhen I turn the ignition and the wait to start light comes on for a split second and I get no audible ping as it normally would. Sometimes the engine will start but mostly not. Have changed the the Glow plug relay and the CPS.
View 12 RepliesI guess it would be classified as very intermittent but in the past year I have had 3 separate times when my truck has after a short drive suddenly had zero boost..
Pull over and turn it off for 30 sec or so and all is fine. Cycle the ignition faster than that and issue persisted. It has only happened in colder temps. In all the reading I have done on FTE I've not come across anything similar.
I'm sure there is something on this somewhere but can't seem to find. Getting ready to change injector o rings and see where people say to drive it 200 miles to get it running right again. Well, I am in the process of a conversion and have no tags or insurance on the truck. Trying to fix issues before I spend that money on it because don't know how much I am going to have to put in it to fix the issue's.
Is there a way to bleed out the air so I don't have to drive it 200 miles? Also, how long will it smoke after the injector change to see if it is actually fixed? I know I should probably see a big difference is ICP,IPR and such. Already know it has leaks in the turbo up pipes which will have to be dealt with too.
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
I changed my injectors and glow plugs on passenger side. I tried to start the engine and it wont crank (turn over). I tried to turn over by hand by turning alternator bolt counter clockwise, turns a little bit and then get very difficult. Is this hydro lock? I stuck a suction tube down injector holes and made it to the piston not much oil came out, I think the truck was a little low on oil before I started the project. The starter wont turn the engine over. I even turned the engine over by hand many times before I put glow plugs in to evacuate the cylinders. I don't know what to do?
View 14 RepliesAs soon as I stepped on the brake and started to move backwards out of the garage, pedal pulsed and ABS light came on. Now it comes on shortly after starting and stepping on the brakes. I just finished the drivers side wheel bearing, u-joint, brake pads, rotors, outer axle stub, and all "outer axles" seals replacement.
AllAboutMPG offered a suggestion about shims on the sensor and checking the ring (never done this, figure it out when I'm there later today?) I figured I'd put this here for some additional input and (hopefully!) later be a good search source and fix for fellow members
Here is the original thread. I installed a Timken complete wheel hub unit with new sensor already installed on the hub.
[URL] ....