Ford 7.3L Power Stroke (1999-2003) :: 2000 Truck Taking Three Cranks To Start - Code Is P1280
Jun 18, 2017
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 1 Replies
Advertisement
2000 7.3 Excursion. Truck ran fine on a 5 hour trip for family vacation. Pulled and to where we were going turn the truck off then what I had to do I came outside try to restart the truck for the next three days it would take 2 to 3 cranks before it was would start. Then on day number three tried six times and didn't start went to bed woke up the next morning and it took three cranks to start. drove it down to mechanic shop near me they have been troubleshooting and think it's an electrical issue the code is P1280; he said there were a couple other codes too and he would tell me what they were later but he never has. I took him a new CPS a new ICM and a new PCM, none of that fixed it. I am at my wits end here and really have to have my truck for work every day.
View 12 Replies
My 02 f250 w/ 7.3 won't start. Cranks and nothing. No smoke or anything. For the last year It has had a intermittent starting problem, where I would drive it for 15-20 mins. If I shut it off like I would if I was at the fuel pump and then restart it, it wouldn't. I'd have to wait 30 minutes with a hood open and then it may start. Other times I would have to wait hours.
I tried replacing the crank position sensor, the fuel pump and filter.I did all this in the Last 300 mile . There's No change. After a week or two of sitting it won't start. What can I check and what can I try.
To add more info. Since I am not the original owner I pulled the computer that is located behind the ebrake to see if someone else had installed a chip, as I've heard that if that chip goes bad then the truck won't start. I disconnected that battery and pulled it. Negative on any chip. Put it all back together and tried again. No start. I borrowed a code reader tonight and pulled a P1280 code. I'm back to square one.
View 14 Replies
This past weekend I noticed I was loosing boost pressure on my 2003 7.3l F250 so I pulled my turbo out found the problem fixed it then put the turbo back in. After it was all said and done I went to start the truck up and it just cranked and cranked a cranked but no start. Worried I didn't hook something up right I checked and rechecked everything to do with the turbo, all good nothing out of the ordinary.
I tried to start again, nothing. Spent all day yesterday trying to figure this out. Replaced the cps still nothing. No movement in tach but I don't remember any on startup anyway. Drained the fuel filter had adequate pressure and such but replaced the filter anyway. Still nothing. Checker all my fuses, one by on and non were blown but I still tried disconnecting my fuel bowl heater and still got nothing. I tried disconnecting the Icp still nothing. There was no oil around the icp either.
I'm getting frustrated that the truck wont start, the truck ran perfectly fine before the turbo removal but now wont even give a sign of kicking up. Just cranks and cranks. Also checked Hpop to see if that's the cause and it's filled like to the brim. But when I'm cranking the truck about 10 sec into the oil pressure gauge kicks up and reads good but only when cranking.
View 7 Replies
Truck cranks wont start. Fuses and relays good, New motorcraft; IPR, ICP with pigtails, New T500 hpop, New 180/80 Injectors, Push rods, 910 valve springs, Mellings lpop. Motorcraft oil cooler.
Reservoir full, oil new 15-40w Amsoil, Rails full, Fuel bowl full and clean, HPOP drive gear rechecked and torqued.
RPM 180
Temp oil 88*
ICP duty cycle koeo 14.8, crank 64.85
ICP pressure 250 -450psi
ICP voltage .27-.50
Manual gauge on oil rail 250 -450psi when cranking
Inj pulse width .0005,
Buzz test was good
Vref 5v all sensors. 12v at IPR w/koeo
Fuel pressure 58psi
Air test hpop hear no leaks with stethoscope.
DTC codes: P1280, P0380
Also put straight edge across injectors to double check they were seated.
View 11 Replies
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 Replies
Started my truck yesterday and drove about 1/4 of mile and all of a sudden I lost all power but was lucky enough to creep back home. Had a friend put it on a scanner and it spit out P1280 and P1316 codes. My truck will start and idle rough but has no throttle response and no power. I changed out the CPS and ICP and the problem still exists. I got an infrared thermometer and checked the heat coming off each manifold and the driver side was reading about 200 while the passenger side was reading about 75 while at idle. Pulled valve pan cover off the passenger side to check and see if the harness came loose and everything looked fine. So my question is do you think this could lead to a bad IDM?
View 9 Replies
Ok I've got an 01 F250 sd 7.3 with 257k on it it just started talking longer to start than it should it will do it cold or hot even if I shut it off at the drive thru takes it like 10 sec or more to fire. My question is I thought about purchasing a autoenginuity to find the problem but not sure the best place to get and what model I should get.
View 7 Replies
E99 Romps on start up and randomly dying. Bought this truck about 3 weeks ago. Previous owner mentioned he had issues with it getting hot and shutting off and not starting. Has new IPR, ICP and pigtail, I just put in a new fuel filter. Has 206k miles on it and is the 4R100.
The past two days after sitting all night I have been cycling the key twice and it hasn't done its romp. Typically when it does I can tap the pedal once and it goes away. This I could deal with but its started to die randomly while driving, never while cruising down the road. Its either just after starting it and rolling slowly or slowing down for a stop or to turn. When it dies, I can put it in neutral and it fires back up no problem. SES light usually comes on for about 10-15 seconds after but goes away.
Replaced the grey CPS that was in it with a dark grey one from RiffRaff Diesel. Got a Edge CTS2 to figure out the problem, the codes Im getting are P1280 and P1247.
The ICP pigtail they replaced they spliced on with butt connectors. I plan on pulling it to check for oil and make sure it does look new and redo the connections with solder then shrink wrap them.
I was told to check the IPR% under full throttle which I did and it never went higher than 36.7
The truck did start running rough around 45-50 mph and I did get a video of the ICP jumping around while cruising down the road.
Then I went through a drive through and the truck kind of hiccuped like it wanted to stall and the ICP went right to 725 PSI and idled up and stayed there until I started to leave.
Truck is pretty much stock, K&N air intake and muffler cut out and straight piped.
Here is a link to the videos I got :
e99 7.3 ICP fluctuation while driving - YouTube
e99 ICP steady at 725 PSI after acting like it wanted to stall. - YouTube
View 5 Replies
I have a 2001 F-350 7.3L Powerstroke. 48,000 miles. I've been having trouble with cold starts. So far it has always started but is taking a lot of cranking, but it hasn't gotten too cold yet so I'm worried about when it does. I ohmed out the the glow plugs and am getting close to 0 resistance. The GPR has 12.5 volts on the hot side and when the relay is closed 10.5 on the other side. Is that difference in voltage in the GPR enough to screw up the Glow Plugs heating up? If I plug it in at night it starts right up. I'm worried about when I am at work for 16 hours and don't have a place to plug it in this winter. BTW this is my first winter with the truck.
View 14 Replies
I am having trouble getting my 2000 7.3 (200k) to start on the colder mornings. It will crank over fast, but won't start without a lot of tries. Today it took 6 pre-heats and cranks, but on others (and colder days) it has started easier. It does seem to be getting worse though.
I have replaced the glow plug relay recently so it *shouldn't* be that unless the replacement is fried. Starts fine the rest of the day and drives fine, but not in the cooler am (it was about 34 this morning). I also tested the batteries yesterday and while they aren't new, they tested okay.
Also, I read (briefly) about the CPS, but forgot to watch the tach this morning, but did notice it is pushing smoke out when turning over.
View 12 Replies
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
View 14 Replies
Ive got a 99 7.3 with 250,000 miles on it. It has run fine all day but just jumped in and won't start. It cranks over but won't fire. Check engine light doesn't come on. About two weeks ago it cut off twice at idle but haven't had that problem since.
View 2 Replies
I have a '99 7.3 that I am working on for a friend. He was moving out west and got to the next state. He stopped to use the washroom, when he came out, the truck would crank but not start. He had it towed back to my house. I have some diagnostic information. Fuel pressure measured at the fuel rail in the head is 60 PSI for the passenger side head. I pulled the plug on the drivers side, it was under pressure and sprayed fuel.. I did not measure it there.
WTS light comes on and then goes off in a normal time frame. Tach shows around 500 RPM while cranking. Engine oil pressure on dash gauge builds up and Low Press Light goes off. Pulled the plug on the High Pressure Oil Res., oil is present at the top. Are there any other checks that I can do until I can get a scanner. My friend has a Snap-On, but he's almost 100 miles away.
View 14 Replies
I have now replaced hpop, injectors, cups, gpr, batteries, uvch on both sides, icp and ipr on my 2002 F550 and it still has a long crank to start.
It has been driven about 1,000 miles since then and no change. I have no codes except buzz test produced a high to low 1272 1274 1276 1278 one time. Cannot get that to happen again.
It is taking 4 seconds of cranking to start consistently hot or cold. It always starts but cranks for what seems like too long compared to my other 7.3s. I have included a screenshot of the data and am curious on what everyone's thoughts are as I am out of things to look at!
View 14 Replies
2000 ford f150 4.6 auto. Will spin over but won't start. checked coil for fire, no fire. Check fuel rail for fuel, no fuel. No theft light flashing and no check engine light on. Has new battery and plenty of fuel in tank. Started fine yesterday but not today.
View 5 Replies
I have a 2003 f250 with the 5.4 in it. When I bought the truck the odometer and fuel gauge weren't working. So I tried disconnecting the battery and when I hooked it back up the odometer started working again and the fuel gauge went from below empty up to full then just dropped back down to below empty and won't move at all. I haven't tried disconnecting the battery again. And I know more than likely I will have to replace sending unit but trying not to if I don't have to.
View 6 Replies
My '99 f350 lost a lot of power the other day, turned out the the injector harness got unplugged. So I swapped those out for oem ones, ohm tested the uvch and injector harness, put a brand new GPR, and still nothing. Cranks over but won't start, what else could it be?
View 5 Replies
I have a 2002 f350 psd. I pulled it inside today to wash it. After washing it wouldn't start. Pcm is working. No oil pressure on guage and no reading on tach.
View 9 Replies
I have a 99 Ford e350 7.3 Powerstroke with about 150000KMS on the clock. However I am having a really hard time starting it in the Cold Canadian Winter (-30). Last week I changed all 8 glowplugs, the batteries, the oil, fuel, fuel filter and yes i always keep it plugged in.
It cranks really well, but it just wont fire not even with a shot of start fluid. I don't know anything about these trucks much less a diesel engine. A guy took a look at it and said my engine needs to b replaced. (I think he is wrong)....
View 11 Replies
My 99 F350 cranks, but won't start, and the "water in fuel" light on the dash stays on while cranking. I have never paid close attention to it in the past. Is it supposed to be on while cranking?
I drained the water from the yellow lever located on top of the engine, and tried to start it. The light went off for the first few cranks, but again the truck still will not start.
I just came from a 10 hours round trip to NC. I filled the truck up two times from gas stations on the way. Is it possible that the fuel is bad? I drove on the same fuel almost 3/4 of this tank and now at the last 1/4 I am having this issue.
A little update:
I took the top of the fuel bowl off to see what the filter looks like, and it is nasty and completely black. I could not tell if the fuel in the bowl contained any water, but it looks greenish and uniform, no the obvious separation that happens when you mix water and oil.
Could the fuel filter be the problem?
A little history about the truck. It's always hard to start if cold and not plugged in overnight. I know it's the glow plugs relay, so I just keep it plugged in all the time until I get a chance to fix it.
IDM was acting up shutting off half of my engine, but I took it off, cleaned it, plugged it back in and it has been working fine for over 2 months.
View 14 Replies
