Ford 7.3L Power Stroke (1999-2003) :: 2000 - Truck Missing And White Smoke Coming Out - Code P1316
Mar 18, 2007
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 Replies
Advertisement
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
View 5 Replies
I have a 2001 7.3 that almost has everything practically brand new... new hpop, water pump, uvch, gpr, glow plugs, icp sensor, ipr sensor, cps and new turbo pedestal that was leaking oil, well now my truck has a cold start to where it has to be plugged in to start and when it finally does it smokes white pretty bad, misses and sounds like it's jumping around under the hood up until it warms up and revs fine with less white smoke but still a miss!!
Compression on test has been done, and good, fuel pressure is good, but the buzz test when cold shows 123457 muffled and quite and when the truck is warm only 3 and 4 are still muffled and quite? Injectors sticking?? Or just need New injectors!
View 14 Replies
Just a heads up when it comes to this code. Today at work I was working on a 2000 f350 that the driver neglected on telling me he had a CEL on and truck was kind of sluggish (drivers are idiots they cant tell the difference) but no miss or any sign of problem except the CEL (he had electrical tape on the cluster. Well I put my AE to see the vitals and immediately code p1316, so I went to do a buzz test revealing that cylinder 1,3,5,7,6 were short to open circuit (forgot the codes) but they all sounded healthy. My next step since it was a quick and easy to do was to check the passenger side uvch to see for burnt pins and what not but everything checked out.
Checked the driver side #6 cyl for the same problem bit a no go. I ohm tested the injectors all of them checked out, wires all the way to the idm checked out so at this point I was in my atemp to see what the hell was going on I decided to install my obs idm on, and guess what happened next it worked immediately the sel did not come up and when I test drove it, my god it felt like a new truck.
Just a side note the idm, had no sign of water damage, and like mentioned to the untrained person most would not tell the difference on how it ran. To anybody that has checked and can't find the problem make sure you really and I mean really check your IDM really good.
View 9 Replies
My 02 excursion is missing at idle and jars the whole truck around going approx 50mph feels like good amount of power loss but still pushing 30psi boost, just got autoenginuity all injectors buzz fine on the test, contribution test show balance fault in cylinders 1&8, should I look for o-rings to be bad, uvch, cups cracked or what ----- turbo fine, hpop great condition, new IPR, new fuel pump and hutch mod, about. 250k miles on truck nothing else major showed up on ae.
View 5 Replies
I have a 2000 Ford F550 7.3. I bought a Superchips programmer to read the codes on my truck and up pops this P1316, so I did some research and found out that the most common problem is the injector wiring harness. I bought new valve cover gaskets and the injector wiring as well because the truck is old and I figured new wires wouldn't hurt.
So after installing the new wiring harness and gaskets I'm still getting this Code! The truck idles rough and serge's sometimes, also there is a lack of power and some shaking between 40 and 50 miles per hour, however form 50 to 60 MPH seem's to be just fine. I don't trust the "Mechanic Shops" around here and will only take the truck in as a last resort.
View 10 Replies
I had some starting issues a little bit ago, but got those sorted out- I installed a new ICP a few days ago and haven't had any more issues. We came up to the mountains last night (got down to about 35), and now it won't start this morning after 3 GP cycles. So I tested the GPR, and the always hot post was, well, always hot. I tested the other post with ignition on, and it had nothin.
Luckily I had a new GPR, so I swapped it out and everything tested normal on both posts. Still won't start. I'm getting white smoke so I know there's fuel (plus my pressure gauge is at about 58 psi). What else am I missing? I've also tested all the fuses....
View 14 Replies
my 2000 f350 7.3 is acting strange lately. Its got 252k and is all stock other than exhaust,intake,ww2. It smokes white every random once in a while for some reason. At start up it wont though. If i get on it every once in a while it will smoke white then go to back to black. Im not consuming coolant, and the oil looks fine, no residue on the oil cap and its not puffing out the oil cap either. Other than that its running great just dont know why it goes white every so often.
View 14 Replies
I just came back from a 200 mile trip and parked my truck. Next day, got in the truck and turned the key.... it turned over and white smoke coming out the tail pipe. After doing some research(you tube),I ruled out cps sensor because it was showing low rpms on tach. Replaced glow plug relay and still have same issue.. what else to look at that I can do without getting it towed. Hunting season coming soon and I need the beast.
View 14 Replies
What do I do? Do I need a new IDM?
View 3 Replies
Today I drove to dinner in my 2012 6.7 with no problems then on the way home my brother said he noticed my truck was white smoking quite a bit and he said there was a very strong exhaust smell coming from my truck ( he was in his car behind me) I ran a diagnostic test and what came up was code P0401 (I believe that's right). Need to figure out what is going on with my truck before I take it to the mechanics and get charged up. The truck still has DPFs in it just has a DPF back exhaust and has a AFE cold air intake running on a stock tune. However I do have the DPF deletes and EGR delete sitting in my garage just haven't gotten them on the truck yet.
View 2 Replies
Wife put fuel in my truck drove it home and as soon as I started it back up it was running rough as hell. When I got to the freeway it got real rough at 1500 rpms in overdrive. If I bring it up over 2000rpm it's better but still feels rough. When I got off work and started it up I got the p1316 code.
I did some research tested plugs on the valve covers a few pins were over 5ohms so pulled the valve covers did the 50cent mod to shimm the under valve cover wiring harness. All pins are around 3.5 ohms. It did not fix the problem.
I then dropped the tank thinking maybe the pick up was gunked up. I've read all the horror stories about the delamination in Ford tanks. Good news is that I have a plastic fuel tank. Bad news is the screens though dirty weren't dirty enough to cause my problems. Where should I go from here?
View 1 Replies
I have a 03 7.3 runs like crap. buzz test says cyl 2 and 4 have high to low side open. the only code that's hard is p1316. it also says cyl 1-3-4 fail balance test but not always some times only 2 fail.... I ohm tested injectors all the way to the idm and all are between 3.1 and 4.2 ish. So I guess I can rule out wiring. it smokes pretty bad if I rev it. it was running good till I parked it for 2 days. I did put HSS in oil 2 weeks ago to try clean out little rough acceleration. I did find my ipr nut fell off and spacer ipr was just floating around on the shaft I put that back together it was laying there.
View 8 Replies
Here's the story. Truck has showed no signs of rough running. Wife drives truck around town. Truck up to temperature and doing fine on a 90 degree day. Stops at red light. Makes left turn engine light comes on truck seems to be running on 4 cylinders. Pulls over light goes off engine idles perfect. Pulls back on road light on no power. Gets truck to a local friends house lets it sit til I get off work.
I check for codes get p1316. Drive truck toward my house no problems for 4-5 miles then does the above with me. Limp it home. I know it is pointing at a wire problem to injectors and or IDM. Did a buzz test passed fine. Plan on pulling valve covers and looking for the usuall things. Any thing I am missing? What will a kOEO test tell me? Should I run one? How common is IDM to go out? One last thing just put a rebuilt transmission in it 3 days ago may be unrelated it seems to be doing fine.
2003 f-350 cc 7.3.
View 11 Replies
I keep getting my SES light coming on in the morning when my engine is cold. I'm getting code p0603 and p1316. I was told the first one is just from using my tuner. The second code is the injector driver module, just trying to figure out what is causing it to throw the SES light only when cold.
View 6 Replies
I'm running a 2000 f250 7.3. The truck has been stumbling for the last two years intermittently. I did the 50 cent mod last fall to the uvch's. Changed CPS, idm, air flow sensor. This last week it finally threw the p1316 code so I have something to go off of. Trucks falling on its face so I parked it. Tore it down last night. Ohm tested all the injectors last night cold and all read around 3ohms. Tested the uvch's and continuity looks good on both sides. Tested them through the valve cover seal, tested fine. Tested them through the first harness and fine. All I have left to check is all the way to the idm. Still no luck finding the problem.
View 9 Replies
Well, truck is throwing me for a new loop the day I pick it up from the body shop (crazy, right?). I started out driving it and had a blue haze - I figured it had some air left in the system from doing my injectors so I left it and it cleared up after about 20 miles. I noticed that my SES light came on while idling at a stoplight, but went off when I took off. Figured it was a fluke and kept on getting on.
Well, next light it does the same thing - idle the light is on, take off the light is off. Reading the code yields P1316 - so I pull over and running a buzz test to fetch the IDM codes. Guess what? No codes. All sounded fine, so this is where I got really confused as I'm getting huge mixed signals from this truck suddenly.
As I got to watching my gauges, I noticed that I was idling around 10.8 IPRDC and 530-560 ICP, and when I would get about 16-18 IPRDC the code would go away. Did a near-WOT run when getting on interstate as a test to see how it'd do, and saw IPRDC get up to 98% - the highest I have EVER seen it get on this truck (no idea if it is related or not). I have a log from moving around the lot that I will try and upload soon.
View 2 Replies
I have a 2003 Superduty with 193k miles that is bone stock. I sold the truck to a friend and when he decided to not pay the remaining balance on the truck, I took back ownership. The truck was having heating issues and it set at a mechanic shop for nearly 2 years waiting for a diagnosis on the heating issue. Fast forward to the present and I now have the truck at my home. Heating issue was the radiator but this is no longer a concern. When I went to pick up the truck from the mechanic, the truck started fine. Every other day for the last 4-5 weeks I would start the truck with no problems.
I get the truck tagged and start driving it on a daily basis. I've put several hundred miles on it but the more I drive it, the less it wants to start. Now it's to a point where it only cranks but won't start. I can take a gas rag and hold it in the intake and eventually it will start. Once it's running, it runs great and has no issues starting. But once it sets for 3-4 hours, it won't start without some sort of assistance.
While trying to find the issue, I've found and repaired 2 fuel leaks and in the process I replaced fuel filter, air filter, replaced glow plug relay, replaced batteries, replaced CPS. Fuel pump is working fine. I've tried the ICP test and doesn't make a difference.
The glow plug light or WTS light works so don't think its the GP. The CES light was on. Had it scanned and it was the air bag sensor so no support from the CES.
While I was working on it yesterday and after cranking on it for 5-10 minutes, it would act like it was going to start and black smoke would be coming out from the exhaust. I let it set to cool the starter it fired up like it had no issues.
View 14 Replies
If the fuel relief valve is stuck open would it possibly throw a P1316 code?
View 4 Replies
I've been battling this truck for over a month now and starting to go a little crazy, It's a 2001 f350 7.3L, with a "used" 7.3L engine from a 1997. Transferred all the necessary parts to make it happen. Keep getting the evil p1316 idm codes detected coming back upon start up. Anywhere between 5-30seconds after starting the left bank dies. I've gone threw and replaced the IDM with a reman unit. New valve cover gaskets (with new harness). even went the extra mile and put in a new power wire (for the driver side) running directly from the new valve cover into the IDM bypassing a connector above the left valve cover. All injectors are checking out around 3ohms. With glow plugs all around 1-2ohms. What's interesting about this is, I can disable any one of the injectors on the left bank (doesn't matter which one) and the engine runs great considering it's down on one cylinder. But when I hook up that last injector it will kill the whole left bank again.
View 13 Replies
I didn't notice anything until I was towing yesterday and tried to pass a car to get onto the offramp.
Anyway, I went to floor it so I could get around and, in my mirror, I could see a decent bit of grey smoke coming out. What could it be?
It doesn't smoke at all on startup and runs smooth right away.
View 7 Replies
