Ford 7.3L Power Stroke (1999-2003) :: 2000 - Smoke On Cold Start - Oil Filter?
Dec 13, 2015
2000 F350 with 340000 on it, have had it for the last 140000. It's an old service truck from south west gas with one owner in between them and me and he put about 5000 on it. I have the big cylinder open air filter, billet compressor wheel, 4" exhaust all the way and an Edge tuner. Don't have any codes I can pull with the tuner. Have been good to me so fare only need regular maintenance, but always had smoke out oil filler with a little pulse.
2500 ago I changed oil and add 1/4 of Lucas oil. 3 days ago when I started in the morning it smoked white smoke out the exhaust as a steam train and idle rough, but cleared up as I went down the street and will do so every time I start cold or warm. Ok, might need new GP, did that yesterday yet the same. Now I start checking stuff and have smoke out the oil filler as a steam train so the cap won't stay.
I know it sound like alot of problems, just try to verify some of them. The smoke out oil filler is blow by? The smoke on start up is that related to bad injectors? Can a bad injector dumping fuel create the blow by? Coolant level ok Transmission fluid level ok Engine oil Rotella T6 added 3 quarter in 2500 miles. I do not have a scanner or any other advance test tools.
View 9 Replies
Advertisement
When it is cold out side like 20 degrees I'm having problems starting my 2000 7.3 I'm cycling it about 5 times and misses smokes white for a bit then stays running I was thinking of changing out the fuel filter. What it could be?
View 6 Replies
Got a 2002 7.3 F-350 with 300,000 miles and for the last couple of years I've been getting blue smoke on cold morning start ups and its been gradually getting worse, it clears up after about 30 seconds and all is normal,No loss of performance, Oil consumption is minor, however I hate a vehicle that blue smokes, I'm guessing my issue is valve seals are worn, I was wondering if it is possible to replace the seals while the heads are on the engine? and was also wondering how much time it would take to fix? as i would have to have it professionally done. I know its hard to guess a time frame and everyone is different. Sounds like textbook valve seals to me but is there anything else I should check first?
View 14 Replies
Ok I'm working on a 2000 7.3 on a F550 truck was running but had no power so we changed out all the injectors and glow plugs and rebuilt the turbo now there is no start it turns over and were getting black smoke from the tail pipe. What is going on with it?
View 2 Replies
20 degrees out this morning truck not plugged in, didn't want to start had to cycle 4-5 times, each time waiting for glow plug Light to go out.
Finally cranked didn't sound pretty but cranked. Once it started idling on its own got out and seen a puddle of oil under the front of the engine drivers side center kind of.
Got up on the truck and shined a light in the valley and seen a puddle in intake valley. Heres my question? Where did this oil come from? Once it warmed up it quit and oil kinda disappeared from valley???
I had turbo off a few months ago because I thought I had a bearing down in it, but found some bolts lose. When I put turbo back on I broke the wire plug on front of the pedestal so I just left it unplugged. Very hard to cold start now that that is unhooked.
Did leaving this unhooked create a hard cold start? Should I put another pedestal on it with the plug or install one without it? Also will it hurt to leave plugged in overnight?
View 13 Replies
I recently purchased a 2000 7.3, when it's started cold it's lopes at start up unless I give it some gas and then it's perfectly fine. If the truck is plugged into the engine block heater it starts normal. I changed the oil the day after I bought it and put 15w-40 in it and then the rough idle started. So I don't know if it was like this before or because of the thicker oil I put into in the cold. It also has a service engine soon light on and the code that comes up when read is to the icp sensor. When looking st the sensor the blue wire going to it looks cut and is disconnected. How would I reconnect these wires and see if that makes the check engine light go off.
View 2 Replies
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
View 4 Replies
Shut my truck off for about 15 minutes and wouldn't start back up. Installed new fuel filter. And gonna try changing cps. Torque says Rpm 180
Ipw. Bouncing between 600 - 3000 Hpop. 250 while cranking Voltage 10.9 while cranking. Ipr starts about 15% and slowly climbs to about 88%
Fuel pressure about 65%
Tried unplugging cps. Gonna check oil now though I check it every time I fill up and it never uses any.
View 10 Replies
Recently since the weather has been cold. between 0-30 degrees or so. My 2002 7.3 with 161k on it is smoking a decent amount i think. far more than i ever remember it smoking thats for sure! anyways its a combination of blue and white smoke and it doesnt last long when the truck starts maybe 1 minute and the smoke stops.
But I also notice when i rev the truck maybe around 1200 rpms the engine shakes very bad. so i was thinking maybe a glow plug went bad making the engine seem like its missing. but even when its warm i rev it up to 1200 and i still feel the engine shake slightly. Maybe im just being picky when its warm? I need to test the glow plugs and go from there but i want opinions about that issue. the truck sits for 4 hour periods and every time i start it i have smoke. I will pay attention tomorrow morning if it smokes after being plugged in all night and post my findings.
My other issue and this typically happens when its below 20. sometimes i will go to accelerate after coming to a complete stop and the truck kinda has a very weak rev to it then just takes off like the tps took a break on me. sometimes i have had it jerk the truck when the throttle catches and other times it creeps at first then takes off like a boost of power.
lastly and this little issue happens most noticeable at 35 mph. i feel a surging im thinking this is related to the tps but i put the truck on cruise control and i still feel the surging. maybe this ties into my second issue? bad TC? ive plugged in my scanner and the only thing jumping out at me is the icp hunts about 100 psi or more at idle. i plan on doing a WOT test on the HPOP, ICP and IPR tomorrow and see if maybe this is just a weak hpop causing my issues.
Repairs i have done:
new 8th injector and all new injector seals about 25k miles ago.
new ipr
new icp
have CCV mod done and 4 inch turbo back exhaust
new map sensor
cleaned out the EBP sensor and tube but that was probably 40 or 50k ago now.
gray cps and i cant remember when i put that on.
gutted the EBPV
bellowed up pipes
no tunes the truck is factory as far as that goes.
View 11 Replies
my 2000 f350 7.3 is acting strange lately. Its got 252k and is all stock other than exhaust,intake,ww2. It smokes white every random once in a while for some reason. At start up it wont though. If i get on it every once in a while it will smoke white then go to back to black. Im not consuming coolant, and the oil looks fine, no residue on the oil cap and its not puffing out the oil cap either. Other than that its running great just dont know why it goes white every so often.
View 14 Replies
I didn't notice anything until I was towing yesterday and tried to pass a car to get onto the offramp.
Anyway, I went to floor it so I could get around and, in my mirror, I could see a decent bit of grey smoke coming out. What could it be?
It doesn't smoke at all on startup and runs smooth right away.
View 7 Replies
Picked up my 5th wheel this afternoon from being raised 3". Dropped over the 10 percent grade down the hill to normal driving. Had the trailer brake controller to boost #2 (Prodigy controller). Had to brake pretty continuously, (tried to stay off it a bit, but is is about 10 grade for about 3/4 mile. Put the auto trans in D2 to get brakes come to the red light at the bottom. Noticed a puff of smoke at the front. Driver side, didn't notice passenger side.
New pads and new slotted rotors new maybe 1,500 miles ago. Not liking that action, but need thoughts. Want to put a thousand or 2 miles towing this summer and accompanying mountainous terrain and back.
2000 F350 Lariat Super Duty 7.3 4x4 NOT a dually.
View 1 Replies
I have a 99 F3 50 with the 7.3 L I am done a lot of work to replace the HPOP pump and the ICP sensor as well as the IPR it cranks but does not start it will sputter and smokes but doesn't run SOS. Also there are no dtc in computer....
View 8 Replies
Alright. 99 Ford F-250 4x4 Ext Cab 287,000 miles. I know she is getting a little long in the tooth but this issue is new within the last month. It does seem to be better when it has been plugged in. On start up I smoke out the neighborhood. Blueish/White smoke, also sounds like it's missing on a couple injectors. Doesn't matter if you cycle the glowplugs a good long time. No luck. Glow plugs are 1 1/2 years old along with injector o rings. Only thing new is I changed from Rotella T-6 to Delo 5W40 Syn, but it was doing it before the switch as well. I tested my glowplugs relay and that is working fine. Could I have lost a UVCH? Fuel filter six months ago or so.
View 14 Replies
For the past few days I noticed my truck would be really rough to start and a lot of white smoke. but once it ran for a minute or less it would be fine. Today when I got home I popped the hood and was looking for anything and noticed my degas bottle had this weird fluid inside on top of the coolant? So I popped the cap off and smelt it and its fuel. Of course this would happen to me. Now I'm not going to lie I have beat on it a few times this week but nothing so so serious.
Could this be contributing to it? Could it be a head gasket? now being a diesel mechanic I doubt its a head gasket simply because there is no oil mixing. I am praying its nothing too major. Once I have the narrowed down to what it could be ill see if its something I could tackle or if the stealership has to do it, which I am not looking forward to. I'd rather be down a truck for a little bit and save a boat load of cash.
View 14 Replies
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 Replies
Here's the deal. 99 Powerstroke out new injectors and orings. Did orings twice to make sure i didn't damage it. New turbo, new utvc gasket, new ipr, new fuel pump, I new complete engine wire harness. I pulled the injectors and ran in another truck no problem. New injector cups compression was all in the 300-375 range. Any cold start smokes like hell. Goes away when driving after the first time of hitting boost. Spits and shudders for a few seconds until boosting. Every time I stop it starts smoking again at idle. No power loss not using oil. Can't get a grasp on this smoking issue. When cold start I kill millions of mosquitos in a one-mile radius.
View 3 Replies
I just replaced my up pipes, turbo pedestal O-ring, ICP, IPR, New O-rings in all my injectors and torqued to spec, new glow plugs, glow plug relay, oil loom wiring harness, new O-rings on oil cooler, oil filter, oil, and antifreeze. I have tried and tried on upwards of 75 or so time to get it to turn over. A little white smoke came out and it sounded like it wanted to fire up, but only a few times.
I have good batteries and a charger on it, 3-4 tries in 5-10 second bursts or longer if it doesn't lose power every 30 -hr. oil is in HPOP too. just found out my block heater is dead, but I shouldn't need it now. Tach moves a little when I crank it but only when my oil pressure gauge hits half way and that about the time it wants to start and starts white smoking.
2001 F-350 7.3 auto 2wd 4dr longbed 329,611 ml
View 14 Replies
So I've been having issues with starting my truck lately. It was really hard to turn over, would start really hard when it did and would blow some black smoke. Turns out my starter was bad so I replaced it with a DB Electric high torque starter. Now it starts up great... for the most part.
I'm still having some black smoke when it's a cold start and/or I have the key set to "On" to warm the glow plugs for a few seconds. It's almost like the starter is turning over the engine, but for the first few turns it sounds empty or hollow (at least that's the best way I can describe it). After the first turns it will sound normal how it's supposed to and will fire up shortly after but with some black smoke.
If my car is already warm it cranks right up without any smoke unless I have the key set to "On" for a few seconds to warm the glow plugs like I said earlier. Pretty much if I warm the glow plugs it makes it harder to start up for some odd reason.
What might cause this or how to fix it? Maybe some of my glow plugs are going bad, or possibly my IDM? I used to have the P1670 code by itself, however, that went away when I replaced the starter. I also just replaced my camshaft position sensor just to be sure it wasn't going bad. I've also been having some boost pressure leaks if that's relevant at all.
View 8 Replies
99 Ford F-250 4x4 Ext Cab 287,000 miles. I know she is getting a little long in the tooth but this issue is new within the last month. It does seem to be better when it has been plugged in. On start up I smoke out the neighborhood. Blueish/White smoke, also sounds like it's missing on a couple injectors. Doesn't matter if you cycle the glowplugs a good long time. Glow plugs are 1 1/2 years old along with injector o rings. Only thing new is I changed from Rotella T-6 to Delo 5W40 Syn, but it was doing it before the switch as well. I tested my glowplugs relay and that is working fine. Could I have lost a UVCH? Fuel filter six months ago or so.
View 6 Replies
I noticed about 1 year ago I had diesel in my coolant but wasn't sure.. took it to a Ford Guy about 45 minute's away.. He seems to know his stuff but when he tested the coolant the results said less than 2% diesel.. But he did find an injector issue and swapped it out..
Forward to present.. there is diesel in my coolant now , since the level is rising to almost overflow and I believe this has been doing on for quite some time as I have that smell you get in the cab..
BTW - All injector cups have been done about 3 Years ago.. On another note , I get white smoke on start up especially if the truck has sat for a day or 2.. What can cause diesel in the coolant.. I did a complete coolant flush this summer and was super **** about getting all the old coolant and gunk out.. Ended up with only clear water coming out the degas
View 14 Replies
