I have a 2000 f350 7.3 got a check engine light that turns off when rpms go up and a slow start. My mechanic said that there were no codes being blown, what is going on?
View 11 RepliesI have a 1999 f250 7.3 I was driving down the road today and I lost throttle along with my check engine light coming on. I pulled over and turned my truck off and now it will not fire back up.
View 6 RepliesMy 2002 7.3 engine makes a slow tap sound...
View 2 RepliesI put a 150 w converter into one of my 12-watt power female and all of a sudden when i turned the engine on my check engine light came on with 4 glow plugs bad and now won't pass smog. any way i can turn off the check engine light so it won't comes up on the smog test?
View 3 RepliesI bought my 2000 7.3L Ex as salvage back in 2005. It had been through a driver side rollover and the seller had restored it. We lived in North Idaho then. But I remember I always had an issue with the check engine light being on. I don't remember what the codes said, but many mechanics read them and determined that nothing was wrong. Many surmised that someone had put a high performance chip in the computer and that was what was causing the check engine light to come on. All of them reset the computer and every time it would come back on. Should I replace the computer?
View 14 Replies1999 f250 7.3 101k California truck ... Scanned it said #1 glow plug did not clear the code. But now the check engine light is off again...
Questions : Harness issue ? Glow plug bad at 100k ? Glow plug controller ?
Start at glow plug work way back to GP CM or in reverse ?
Replacement Do all 8 or just the bank of 4 ?
Thoughts on replacement brands
Accurate diesel glow plug replacement kits any good, will they last ?
Or go factory glow plugs
What about Felpro gaskets
I heard about another brand of GP CM
2001 F350 290,000 no mods other than 6637, 2WD
Towed our new to us RV home last, only 15 miles from the dealer and yes its a big 5th for my truck at 12,000lbs. Anyhow, about 2 mins from home as I'm pulling off the freeway I got a SES light come up, then it disappeared. I checked codes this morning using forscan and nothing shows to indicate what it may be.
I was wondering if the transmission is getting hot if it throws an SES? It was only a short trip, but I have no real idea of the condition of the trans as the truck is new to us too - fluid looks and smells good.
Only new code is an ABS one c1229, c1233, C1234. I had 2 of them before - think the 1229 is the new one.
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
Cooler weather has arrived and my 2000 f250 won't start. Wait to start light is coming on, no power passing through the two relays on top of the engine. Are both of these for glowplugs? My 97 only had one. How do I diagnose relays on this truck? If you cross out the two relays truck fires right off so I know the glowplugs themselves are good.
View 7 RepliesNow that I have been driving for a while I kept seeing this light come on/off and I did a video below - I don't generally flash my lights so don't think I am aggressive - but I wanted to make sure to capture the video and the light coming on.
I was thinking valve cover connection the 50 cent mod - and maybe it's all coincidental - but I did have to pressure wash the troph where the oil collects and maybe something else got knocked loose.
[URL] .....
I have a 2002 F250 4x4 Powerstroke with Automatic. I have been having off and on issues for months with the throttle going dead. This only happens when I start it, if it works when started it will continue working until a different start session.
I have replaced the pedal several times before learning how to check its output with a meter and am quite sure that is not my issue at this time. However, when the pedal is depressed the check engine light lites up and nothing happens.
I am thinking it must be the computer itself, but was told there is another sensor or module under the hood that could cause the issue also which is several hundred dollars to replace as would be the computer.
Is there a way to test the computer, and what is this other module/sensor if it exists that could be the issue? Unhooking and rehooking the battery to reset the computer is no longer working to buy me a few more weeks, is there a simple way to reset the computer to try?
I love this truck when the throttle works but I am getting tired of paying on a truck while having to borrow a vehicle to drive to work.
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
Light came on a few days ago. 2000 exc with 7.3 diesel the mileage report said 155000. Took it to Autozone a hour ago and these are the codes: P0683, P0676 and P1670.
View 14 Replies2002 F350 7.3 PSD. 192k miles.
From my understanding, a CEL is supposed to illuminate each time you turn the ignition ON as part of normal startup procedure.
I figured the previous owner must have pulled out the bulb to hide the fact that the truck had a few "issues" before selling it, so today I pulled out the gauge cluster and it looked as if the CEL bulb was a tiny LED soldered directly into the gauge cluster itself. There were a few serviceable/removable bulbs for things like turn signal indicators, high-beam etc... but the CEL did not have a serviceable/removable bulb.
I've been driving this truck and working through it's "issues" and fixing things as I go, but it keeps throwing codes without the CEL illuminating. What's going on here?
I thought the check-engine-light was supposed to illuminate each time the ignition was turned on, and that it would come on each and every time the vehicle registered a fault code in the ECU/PCM.
My 99 250, 7.3 is having some strange issues as of lately. When I start it in the morning, when the engine has fully cooled down, it starts right up, then it throws the "wait to start light" runs real rough and just shuts off. Run the glow plugs a few times, start it up and it will do the same thing for maximum 30 minutes, then all the sudden I start it and it runs fine. I've replaced the fuel pump, cleaned the fuel bowl, new fuel filter, I just don't know where my problem could be. It doesn't make sense. But once I get it running and it warms up, runs fine all day. Go to bed, wake up, has problems again.
View 14 RepliesIf I leave my truck sit for a couple of days, the batteries are noticeably weaker. It's fine overnight, but two nights and it's slow to crank. Three and it won't start without charging the batteries. I checked for a drain last night and found that it was drawing 1.2 amps.
That seems like a lot, no?
It's a 99 f350 7.3 diesel powerstroke. About 180k miles I think.
It cranks fine. I just changed the glow plugs(all were dead) but when you try and start from cold, it takes about 7-10 seconds to fire. The oil res is full, tried disconnecting the EOP sensor, still fires up and takes just as long. There is one near the oil filter, and that seems to not be it either.
Doesn't smoke, no oil leaks that I know of. Not sure what else to check before sending it to another shop to get put on a diagnostics machine. I read about the IPR, but it has no problems when running. Only problem is a very long time to start. Also changed the fuel filter.
I have a 2000 7.3 f450 having some electrical issues. When you turn the key on sometimes the dash will start ticking and left side light flashing...engine will turn over but it won't start. The ticking is coming from under the hood relay 32 (you can hear and feel it clicking). Book says its injector driver module power relay. A lot of the times it will start fine other times it will be running and just die (prob because of this issue) happened once when I was driving.
What to check here already replaced the relay still have the problem.
I have 2001 F250 7.3L 261k miles.
Over the last few months, I have noticed that my truck is taking longer & longer to start after sitting for a long time (i.e. every morning, after work, etc.) When the problem first started (3-4 months ago) it would crank for 2 seconds & nothing so I would turn it off, let the "wait to start" light go off again (depending on outside temp 10-20 seconds) & then it would crank & usually fire right over like it was new. That seemed to happen only in the morning when it was 70 degrees or colder outside but no problem after work when it was 80+ degrees.
As the weather has gotten colder, it has gotten progressively worse. A couple of weeks ago, it was in the 40s in the morning & it took a solid 8 or 9 minutes of cranking for a few seconds, then trying again before it started. Once it started it did "chuga chug" a couple of times before it smoothed out. Last week when it was 16 degrees in the morning, it wouldn't start at all. I tried for a solid 15 minutes before I gave up.
I will say that as it has gotten worse over the last couple of months, I have noticed that it's cranking w/o firing but I will hear it fire once or twice per crank before it will fire up & run. Once it starts, it runs like a champ. No studders, stalls, slow acceleration, etc. Pulls like it always has. The weirdest part about it is that once it starts & runs for 30-60 seconds, I can shut it off & it'll fire right up every time. If I get it up to full operating temperature, I can go back & start it right up 2 or 3 hours later w/o a problem.
I did notice my oil cooler is leaking pretty badly (that will be fixed this weekend) & my valley has fluid in it but it's hard to tell if it's diesel, oil or a combination of the two because my truck is setup to run on WMO (waste motor oil). I have dual tanks so the OEM tank is diesel & the auxillary tank is WMO. I have 2 mechanical fuel pressure gauges on my fuel bowl, 1 pre & 1 post fuel filter as well as an aftermarket Walbro fuel pump. The fuel pressure when running on WMO has always bounced a little bit between (65-75 psi) but the fuel pressure on diesel has always held solid at 75 psi until recently when I have noticed that it flutters a very small amount between 73-75 psi.
I have verified that the GP Relay works & was leaning towards a glow plug problem but considering it was having troubles at 70 degrees ambient temperature, I'm hesitant to think that's the true problem. I think that might just be adding to the problem. I live in the south so my truck doesn't have a block heater but I'm going to add one this weekend when I replace the oil cooler gaskets & o-rings.
I'm also going to pick up a new Android tablet today (replace my broken one) so I can use the Torque Pro app to monitor ICP, HPOP & InjPW. Finally, I had a DP Tuner chip on it & to remove that as the possible cause, I removed it & the same symptoms continued.
On my 7.3 super cab, I changed the fuel filter last Friday and now on cold start the service engine soon light comes on for a couple minutes (approximately) on a cold start. No other issues. Tried scanning with my scan gauge 2 and no codes. (of coarse I think that thing is a joke for scanning). Not sure if this means anything, but last week before I changed the filter I thought I smelled diesel fuel on a couple different occasions. If I actually did it may not even be related.
View 2 RepliesI have an accent 2003 1.6 dohc crank but not start !!! Who do not fire and no gas ... and the check engine light is off when I turn the key on... (I test the check engine light and it is not burn).
I change the engine control relay and this is not work... I have all the wiring diagram and I check wire by wire and I don't find anything...