Ford 7.3L Power Stroke (1999-2003) :: 2000 - Lopes At Start Up When Started Cold
Jan 17, 2017
I recently purchased a 2000 7.3, when it's started cold it's lopes at start up unless I give it some gas and then it's perfectly fine. If the truck is plugged into the engine block heater it starts normal. I changed the oil the day after I bought it and put 15w-40 in it and then the rough idle started. So I don't know if it was like this before or because of the thicker oil I put into in the cold. It also has a service engine soon light on and the code that comes up when read is to the icp sensor. When looking st the sensor the blue wire going to it looks cut and is disconnected. How would I reconnect these wires and see if that makes the check engine light go off.
View 2 Replies
Advertisement
2000 F350 with 340000 on it, have had it for the last 140000. It's an old service truck from south west gas with one owner in between them and me and he put about 5000 on it. I have the big cylinder open air filter, billet compressor wheel, 4" exhaust all the way and an Edge tuner. Don't have any codes I can pull with the tuner. Have been good to me so fare only need regular maintenance, but always had smoke out oil filler with a little pulse.
2500 ago I changed oil and add 1/4 of Lucas oil. 3 days ago when I started in the morning it smoked white smoke out the exhaust as a steam train and idle rough, but cleared up as I went down the street and will do so every time I start cold or warm. Ok, might need new GP, did that yesterday yet the same. Now I start checking stuff and have smoke out the oil filler as a steam train so the cap won't stay.
I know it sound like alot of problems, just try to verify some of them. The smoke out oil filler is blow by? The smoke on start up is that related to bad injectors? Can a bad injector dumping fuel create the blow by? Coolant level ok Transmission fluid level ok Engine oil Rotella T6 added 3 quarter in 2500 miles. I do not have a scanner or any other advance test tools.
View 9 Replies
20 degrees out this morning truck not plugged in, didn't want to start had to cycle 4-5 times, each time waiting for glow plug Light to go out.
Finally cranked didn't sound pretty but cranked. Once it started idling on its own got out and seen a puddle of oil under the front of the engine drivers side center kind of.
Got up on the truck and shined a light in the valley and seen a puddle in intake valley. Heres my question? Where did this oil come from? Once it warmed up it quit and oil kinda disappeared from valley???
I had turbo off a few months ago because I thought I had a bearing down in it, but found some bolts lose. When I put turbo back on I broke the wire plug on front of the pedestal so I just left it unplugged. Very hard to cold start now that that is unhooked.
Did leaving this unhooked create a hard cold start? Should I put another pedestal on it with the plug or install one without it? Also will it hurt to leave plugged in overnight?
View 13 Replies
Recently since the weather has been cold. between 0-30 degrees or so. My 2002 7.3 with 161k on it is smoking a decent amount i think. far more than i ever remember it smoking thats for sure! anyways its a combination of blue and white smoke and it doesnt last long when the truck starts maybe 1 minute and the smoke stops.
But I also notice when i rev the truck maybe around 1200 rpms the engine shakes very bad. so i was thinking maybe a glow plug went bad making the engine seem like its missing. but even when its warm i rev it up to 1200 and i still feel the engine shake slightly. Maybe im just being picky when its warm? I need to test the glow plugs and go from there but i want opinions about that issue. the truck sits for 4 hour periods and every time i start it i have smoke. I will pay attention tomorrow morning if it smokes after being plugged in all night and post my findings.
My other issue and this typically happens when its below 20. sometimes i will go to accelerate after coming to a complete stop and the truck kinda has a very weak rev to it then just takes off like the tps took a break on me. sometimes i have had it jerk the truck when the throttle catches and other times it creeps at first then takes off like a boost of power.
lastly and this little issue happens most noticeable at 35 mph. i feel a surging im thinking this is related to the tps but i put the truck on cruise control and i still feel the surging. maybe this ties into my second issue? bad TC? ive plugged in my scanner and the only thing jumping out at me is the icp hunts about 100 psi or more at idle. i plan on doing a WOT test on the HPOP, ICP and IPR tomorrow and see if maybe this is just a weak hpop causing my issues.
Repairs i have done:
new 8th injector and all new injector seals about 25k miles ago.
new ipr
new icp
have CCV mod done and 4 inch turbo back exhaust
new map sensor
cleaned out the EBP sensor and tube but that was probably 40 or 50k ago now.
gray cps and i cant remember when i put that on.
gutted the EBPV
bellowed up pipes
no tunes the truck is factory as far as that goes.
View 11 Replies
so i was driving along & my 2000 f250 7.3 started to chug then died. I pulled over & it started right back up. I did some running around & was on my way home & it did it again only this time it would barely idle (same chugging). It died again & now it wont start. Turns over strong.....
View 14 Replies
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 Replies
My 00 F350 has never started when the temps were below 25 unless it was plugged in. This year is no different, but now it won't start when it's plugged in. It just turned 200K and I know things have to be checked, but I don't like doing them in the winter so I was hoping to make it through this winter and fix things. I needed to use the truck the other day so I plugged it in before I went to bed, It wouldn't start, so I got looking, crawled under the truck and the block around the heater was cold, checked the plug with an ohm meter and it showed that there was an open, so I checked the cord, sure enough there's a splice in it, with a broken wire, so I fix all three splices, check it again and it's still open, under the truck again, and find another splice at the end of the factory wire loom with a broke wire, got them replaced, got a good reading with the meter, and now I'm back in business, Plugged it in for a couple of hours, hit the key and it fired like it was new. Well not that good but it did start.
View 7 Replies
2000 Ford Excursion, 7.3 PS with 210,000 miles. I am on I40 at a truckstop. I was rolling down the freeway last night when the truck started bucking. I pulled of the freeway and here came a thunderstorm. I waited til this morning to check for codes cheap scanner. I pulled a code P1211. I waited for NAPA to open so I could take it in the shorts. I bought a fuel filter and an ICP sensor. After changing them out, the truck runs then starts missing. My battery is about to die so I will finish post shortly.
View 14 Replies
Truck is a 2000 7.3 PSD Exursion, 300k miles, automatic. Does this when cold, I let warm up for 5 minutes before this happened as its been doing it. Going to plug in tonight, was about 40-50 degrees out.
What is causing this shutter? Injectors? After I get off my dirt road to street it runs fine, also notice the ebpv. Seems to do shutter most when reversing.
Does this when cold, I let warm up for 5 minutes before this happened as its been doing it. Going to plug in tonight, was about 40-50 degrees out. What could be causing this? Injectors? After I get off my dirt road to street it runs fine, also notice the turbo waste gate? Seems to do it most when reversing.
[URL] ....
View 3 Replies
I was out with the F350, drw, automatic, 7.3, 4 x 4, yesterday about 30 miles from home base. The transmission started pumping fluid out the front like I have never seen before. I am not talking a drip, I am talking a stream, a big one..... almost like pouring coffee from a coffee pot. I noticed it when I was backing into unload and was leaving an oil trail, a quite obvious one.
We took off the tc cover as it was coming off that to find a dry tc and flywheel, but fluid running out off the case. This is the second time this trans left me high and dry in 165k miles. The first time was a stripped tc/ input shaft. We repaired the transmission then but I don't think we replaced much besides being sure no debris went though everything, fixed what was broken. That was about 25,000 miles ago.
View 8 Replies
I was driving the truck a couple of weeks ago and it just died. I costed to the side of the road. It cranked but would not start. noticed the WTS light was not on. I bought a new one from dealership and installed it and it started right up. I assumed I fixed it. I let it warm up and drove it around the block and parked it and plugged the battery tender back up. the other day I got in and no WTS light again.
I was going to look at wire bundle over valve cover and 42 pin connector. Is there any other issues, I need to look at? Is it possible I just got a bad sensor? My guess would be something is shorting the sensor out if thats the problem so before I just put a new one in I thought I would ask the pro's. I have not done a lot of work to my truck aside from replacing the water pump, hoses and coolant.
View 8 Replies
OK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.
View 14 Replies
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
View 11 Replies
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 Replies
2003 Ford 7.3 E450 ... Just recently got Auto Enginuity Ford enhanced
The problem....The van will run when plugged in for 2 hours or on either. Once started the van runs good. It will not start on its own even at 60 degrees
I got the following codes
KOER (Key On Engine Running)
P0476 Exhaust pressure control valve range/performance
P0673 Cylinder 3 glow plug circuit
KOER (Key On Engine Running) Cylinder Contribution
P0278 Cylinder 6 injector circuit contribution / balance fault
KOEO (Key On Engine Off)
P0113 Intake Air Temp Circuit High Input
KOEO Buzz Test (Key on Engine Off Buzz test)
successful
View 14 Replies
I just started having a cold start problem with my '02 Excursion this fall and I'm at my wit's end trying to fix it. Truck starts fine above about 45 degrees and when it's warm. If I plug in the block heater it also starts fine in the cold. If it's not too cold I can eventually get it started by continuing to crank it. It blows white smoke while cranking and for a few seconds after it finally turns over. Smells like fuel. Runs rough for 30 sec after starting when it finally turns over. Definitely seems like glow plugs aren't working. This truck started no problem on GPs alone without plugging in down to -20 deg F before this year.
I started by cleaning all battery connections, including the two ground posts on the engine block, I replaced one bad battery (diagnosed by Autozone; other one was OK), I checked the resistance of the glow plugs (only a few years old with about 30k miles on them) through the connectors on the GP control module (all were about 1 ohm), and confirmed 12V at the power pins in the GP control module connectors. I then replaced the GP control module and the problem is still present. Battery voltage drops from about 12.6 V before I start the GP cycle to about 12V when I turn the key to "ON" and the GP light comes on. How much should the voltage drop when the GPs are on? What the heck else could be wrong??
View 14 Replies
Ok truck would not start when cold outside. So I put a gpr on truck. Truck alt would only put out 11.5 ... After I put it on. So I put 4 new alts on all read the same 11.5 and the battery's would drain over night. Turns out they gave me a starter relay. So I have the proper one now. Now when u turn the key the everything is flashing the dash dome light buzzer. But take one of the small wired off the gpr, it stops but I have no power to the starter. It's been 2 months of hell trying to figure it out.
View 14 Replies
So back ground is as such. Truck started fine before I replaced the hpop with t500 and did the driven diesel regulated return. I have double checked everything is plugged in. Now when I try to start it cold it will just crank. Yes I get smoke and oil pressure both places. If I give it a shot of ether it will start right up and run fine all day. What am I missing? Yes I know ether bad.
View 14 Replies
I have a early 99 f250 super duty 7.3l and it's giving me fits. about a month ago the truck started to do a hot no start. drove truck for about a hour. Shut it off and half hour later no start. Let it sit over night and would start with long crank.
Changed CPS no change. Pulled tuner and set back to stock. No change.
Changed fuel filter, no change.
After reading forums changed IPR and truck started and ran great. About a week ago back to the same problem. Battery's are about 2 months old. Oil change and oil filter a month ago.
Checked the hpop reservoir and its 1/2 from the top.
Checked fuel bowl and it has fuel. no sign of oil in it.
Drained bowl and watch bowl fill back up. seems to fill quickly.
Pulled passside valve cover to check for bad orings while cranking.
Every thing seems fine. have not done driver side yet. used FORSCAN and ran buzzed test on injectors and they all buzzed what seems to be about the same. ran test couple of times to make sure. this morning I ran a live scan while cranking and this is what I got right before it started. ICP 660.6psi, IPR 64.84% and RPMs 227. took 8.86 seconds to start. after work scaned again for hot no start and this what I got. ICP 292.9psi, IPR 55.86%. and RPMS 203. unplug ICP and no change. still will not start. one thing I did notice when plugging ICP back in I looked down in side at the pins and can see what seems to be bubbling around one of the pins. the pig tail has just the slights sign of oil.
View 14 Replies
My truck is hard to start when cold and I suspect glow plugs. But it is not showing any codes? If it is a glow plug or glow plug relay at fault , should it throw a code?
View 10 Replies
I have. 2001 excursion with a 7.3l deisel. 167100 miles
It runs great but if it sets over night when the motor is cold it will not start.
You have to plug the block heater in for about an hour or more for it to start.
To me it seems like glow plugs are not working? It had new glow plugs out in from the po.
View 14 Replies
