Ford 7.3L Power Stroke (1999-2003) :: 2000 - Ignition Relay Location?
Jan 13, 2016
I purchased one of the No Start relay for my 2000 Ford F-250 Turbo diesel and need assistance finding the relay to replace.
Originally I thought it was for the fuel pump then then discovered it replaces the ignition relay.
According to the company it's located on the passenger side under the hood. Can't find any fuses there.
I looked in the user manual and found nothing about an ignition relay. Just "PCM Relay Coil, Ignition Coil (Gasoline only), Fuel Heater (Diesel only), Wastegate Solenoid (Diesel only), Injector Driver Module Relay Coil"
The relay I purchased is from: "No Start" Relay, "No-Start" Intelligent Relay System, Vehicle Theft Deterrent
View 7 Replies
Advertisement
I have searched everywhere for the location of the blinker relay on my 02 F-250 7.3 and getting mixed results and still not found.
View 14 Replies
After installing new glow plugs, glow plug relay, and valve cover gaskets my 2000 7.3 is throwing the 1395 code. Glow plug monitor Bank 1. Any input as to cause? Checked all connections to relay. All tight. Read something about fusible link. Where that is located? One side of relay reads 0 volts.
View 4 Replies
Where the fuel pump is located on a 2000 F-350 7.3L Diesel? Also, how complex is replacing this?
View 14 Replies
My 2000 f350 has wires that dont match anything I've seen. I need to mate this to an 08 harness so I need to be accurate. I have
(2) yellow. I know this is 12v constant
(2) green/purple I know this is 12v constant
(1) red/black
(2) solid red
(1) solid black
(1) gray/light blue
View 3 Replies
Just asking where about's the ficm relay would be under the hood of my '04 6 liter, I have 3 boxes to chose from.
View 9 Replies
The #8 fuse under the hood was blowing on my '00 F-250 every time I turned on the healights meaning I would lose power to my park lights. The brown wire coming from the back of the headlight switch showed a dead short to ground that I traced to somewhere between the switch and the firewall.
Anyway, I got tired of trying to pinpoint the ground fault, so I cut the brown wires at the back of the switch and under the hood at the top bolt-on electrical plug and replaced the bad section with a new wire. It works fine now with the only exception being I do not get the park light flash when I hit the remote lock button the second time. I do still get the horn chirp.
My Haynes manual indicates there should be a relay box with a Park Lamp relay, Driver Unlock relay, All Lock Relay, and All Unlock relay. The park light relay looks like it sends the blip of power to the park light circuit. Where this relay box is? I'd like to splice into the brown wir coming out of it to restore the light flash when I lock the truck since sometimes it's too noisy to hear the horn.
View 10 Replies
While doing a visual inspection I noticed that the AIH hot wire (captured nut wire) had broken off and was laying loose. I removed the wire from the relay and made a new 8 gauge wire, I connected it to the relay and was about to add it to the AIH when I got a healthy spark ( it touched the ground wire ) and yes the truck was not running and the key was out at the time.
This sounds to me like the relay has gone south, am I right??? I have a new OEM relay to install but I have a question. In what order are the wires and ceramic fitting go on the AIH post???
View 11 Replies
The relay for the fuel pump keeps going bad. Is this a sign my fuel pump is going ? I just replaced my 2nd relay ( lasted about 1 week ) 1st lasted 16 years. Or is there another issue to look at ?
View 11 Replies
Had a weird issue come up this weekend. I went to drive my truck for the first time in a couple of weeks and when I got in I noticed a constant clicking from under the dash (whether the truck was on, off or if the indicators / hazard lights were on or off). I investigated and found it was my flasher relay. I have replaced this relay recently (within the past year) to an EP27L to accommodate the LED lighting I installed throughout the truck (hyper flash on the old relay doesn't even describe it properly, it was a constant buzz!) and it has been working perfectly until this point.
I thought it may just be something going on with the relay so I pulled it and replaced with the old EP27 unit I still had. It does the same thing, albeit at a slower rate (every 4-5 seconds). The lights do not blink when it is doing this, but still operate normally when I move my stalk up or down or when I press the hazard / flasher button on top of the steering column.
I am wondering if there is a short somewhere in my multifunction switch that is causing this issue? If so, why would it come up when truck has been sat? I didn't have the time, not the inclination to roll around inside my truck (hotter than hades here in Florida right now) to troubleshoot any further. I pulled the relay altogether until I get some time and cooler weather to look into it further. Otherwise the truck seems to operate as normal, even all the lighting seems to have no ill effects from this?
View 4 Replies
Any pic or wiring diagram of the starter relay that is mounted to the fender. I'm trying to start the truck finally but it's just cranking and I think I might have mixed up the wiring. Is there supposed to be a constant hot at the glow plug relay when the ignition is off?
View 14 Replies
Upon trying to start my 2003 f250, it keeps blowing the 15A "Transmission Range Sensor then to Starter Relay Coil" fuse. Initially the truck would still start if i did not use the aftermarket Viper keyless start. however, now it doesn't start at all and keeps blowing fuses. I contacted the guy that installed the alarm thinking it might be something on his end. He walked me through reconnecting the factory starter wires which would isolate the issue if it was something on his end. it's still blowing fuses. battery terminals are good and clean.
View 3 Replies
Alright so I have a 99 7.3l. One day I went to start my truck and when I turn the key to the on position all is normal and then when I turn it all the way to crank it nothing happens. I hear a relay click ann thed that's it. Me and a buddy of mine spent quite some time on going through the entire truck. The starter was replaced, the neutral safety switch was replaced and the ignition switch was replaced yet the problem is still there. We then discovered that fuse #20 under the dash keeps blowing with every turn of the key. The manual states that this fuse is a starter motor relay coil PCM ( gasoline only). So if it's gas only why is it even in there. Let me just say that I can jump the fender mounted relay and the truck starts.
View 7 Replies
Attempting to debug the Horn not working on my 2003 Ford F450, The fuse is good (shown as #37 15 amps) so next I would like to check the Horn relay.
View 5 Replies
2001 F-350, 7.3L,
Has done this off & on for a few years and am tired of it! Noise is kind of a buzzing that seems to come from the flasher/turn signal relay. It stops buzzing when you turn on a turn signal, activate the flashers, or lift up on the shifter arm(?). Had to drive home yesterday with the flashers on! So I see from researching that it may actually be the multi-funtion switch on the steering column. So I removed that, cleaned up all the contacts, and put it back on and the buzzing did not go away.
View 14 Replies
I have looked at several different diagrams of the wiring in my 99.5 powerstroke and I cannot find my abs computer anywhere, where it is?
View 5 Replies
Does Delayed Accessory Relay 306 control radio on an 02 F-350?
View 2 Replies
I have a 2001 F350 XLT with cloth seats. In 2003 I upgraded those seats to power seats.
- When I upgraded to power seats I did not run a new power wire. Since my 2001 was at least fused for power and heated seats I located the Power seat 30amp power wire.
- That wire is located on engine compartment fuse #15 (Circuit 5298 as I recall) and Dark Green. It comes through the firewall and runs down the drivers side kick panel along the floor and then intersects with the power and ground seat belt wires that ran under the seat.
- The ground wire was coiled and attached to a ground stud behind the drivers side kick panel.
About a month ago I had a mouse get in and chew my seat wiring to shreds. I built my own harness and am good to go there, however since I had these seats all apart I decided to replace the foam and add HEAT.
So that brings me to the specific question. In the engine compartment fuse box, there is a 30amp positive wire for Heated seats. My schematic says it is a 14 gauge wire RD/BK on circuit 1153.
Where in the heck is this wire? I have literally tore the dash apart looking for this wire.
- I have verified the following with my fluke continuity tester.
- It is not part of the four customer access wires that drop on the right side of the interior fuse panel.
- It is not part of the tow wire bundle.
- I have checked the bundle that the Dark Green Power seat wire is in and there are no RD/BK wires in that bundle. I also poked the other 2 14 gauge (Yellow/Blue) wires in that bundle and verified they are not them.
-I have checked the three wire bundles behind the passenger side glove box and was unable to locate.
- I have verified it is not stored behind the compartment below the cigarette lighter.
I am looking for info which wire I am talking about and knows where Ford stored them when not used by having the XLT Trim with cloth seats. Yes I am aware that I can run an additional wire with a 30 amp fuse to the batter, but I would prefer to use the system and fuse that was designed for this.
View 2 Replies
How can I tell if my truck has a cabin filter and where would it be located? I looked through the OM but it was little to no luck....
View 3 Replies
Went to start 'er up, key spun forwards, power came on but no start, no click, nada. Turn key back and power stayed on, back forward and no resistance whatsoever power stayed on. Took screwdriver, jumped starter relay and viola away we go. Get home, get cylinder out of hole and the tip is broken off down in the column. BTW, had to disconnect batteries to shut it off. I drilled hole in the tip still in the column, insert screw and no come out. Must need to be turned somehow first I'm thinking.
View 14 Replies
I'm getting ready to put in my new double din and it said to hook the wire for the camera up to the reverse light wire. Which one this is on the harness coming out of the column?
View 14 Replies
