Ford 7.3L Power Stroke (1999-2003) :: 2000 - Hard To Crank - No Power?
May 26, 2015
Iam looking at a 2000 7.3 Powerstroke that has some problems first it is hard to start cranks like it has a dead cyl. Second after starting it has no power not even enough to move. At first it would only run if held wide open but once it warmed up it would idle and rev and move but barely still had a miss. The weird thing is it did not smoke blue-black or white also no strong smell of diesel and no smell of oil at all. The truck has 230ish miles and there are no maintenance records.air filter was new.
View 7 Replies
Advertisement
My wife has been telling me our '01 E-350 (Econoline) with 7.3 is taking several attempts to start in the mornings, like it's not even trying to fire. It will crank like wild but no fire and then it will fire usually and sometimes run a little rough but no always.
Tonight she called me from across town and it won't start at all, cranks like wild but won't start, chug or anything.
The WTS light is working fine, the truck runs great and idles smooth all other times, just been giving grief when starting in the mornings (warm outside 70 degree plus ambient temp). I haven't had the truck do it to me but she has explained it well enough.
I do get a SES light for overboost when I run it hard (PHP tuned) but it always goes away and hasn't caused any issues. Could this be the ICP acting like this? If so, is it true that I can just unplug it and the truck will start by using default pressure?
View 14 Replies
I got a 2000 7.3l with 400,000 miles on it that decided to just not start anymore after I parked it for a couple days. Its always been a hard starter due to needing glow plugs but I can deal with that. it doesn't even try to fire anymore. I replaced the CPS (my tack bounces when cranking). The ICP has oil in the plug so I just unplugged it for now till I replace it.
I pulled the IPR and cleaned it really good and bench tested it with 12 volts and could here it clicking so I put it back in. I can get under the drivers door with the key on and hear the fuel pump running. I gain oil pressure on my dash gauge when cranking. I check all my fuses. my WTS light comes on . I just don't have any fancy scan tools to make this easier. Also just cause I was feeling lucky I just went out and bought 2 new batteries for it yesterday so we are good there.
View 6 Replies
Found icp sensor with oil in plug and codes p1211 and p1212. Icp sensor reading 0 pressure. Changed out icp sensor. Still cranks no start check oil level in hpop resverior, check with brake clean spray nozzle and no oil on it. Filled resverior with oil. She tried to start. Had to put the charger on her and she finally lite off and came to life. Questions, how would that resverior empty out? Was it because I pulled that sensor? Is there s check valve in that resverior hanging up?
View 2 Replies
I have a 2000 F350 7.3 ... A couple weeks ago I noticed that it was taking longer to start then it should be. Now I have to cycle the key switch 3 or 4 time to get it to start. There is a clicking coming from the relay block under the radio. Sometimes the truck will start sometimes it has to be rolled off. I have recently replace the starter and alternator. I have had the batteries tested and they are good. I replaced the two small relays in the block under the radio, one is for the fuel pump and the other I understand is for the door locks? I also read on here the large blue one is for the turn signal so I have not changed that one. After all this I still have the same problems.
View 9 Replies
I have a 2000 F250, 300k. Starts beautifully when cold, takes 10 seconds of cranking when at Operating Temperature. Did the injectors and plugs in September, kept doing it and now that it's summer it's getting harder and harder to start. Just replaced the ipr, still doing it. Gonna do an overdue oil change tonight or tomorrow, I'm hopeing that will improve it. I can understand 3 or 4 sec of cranking, but not 10. Truck hads no drivability issues whatsoever. Will an ICP fix it? Change to a heavy-duty 20w-50? (Last oil change was delo 15w-40) The code reader that I have is really basic, and only shows me RPM and map.
View 14 Replies
20 degrees out this morning truck not plugged in, didn't want to start had to cycle 4-5 times, each time waiting for glow plug Light to go out.
Finally cranked didn't sound pretty but cranked. Once it started idling on its own got out and seen a puddle of oil under the front of the engine drivers side center kind of.
Got up on the truck and shined a light in the valley and seen a puddle in intake valley. Heres my question? Where did this oil come from? Once it warmed up it quit and oil kinda disappeared from valley???
I had turbo off a few months ago because I thought I had a bearing down in it, but found some bolts lose. When I put turbo back on I broke the wire plug on front of the pedestal so I just left it unplugged. Very hard to cold start now that that is unhooked.
Did leaving this unhooked create a hard cold start? Should I put another pedestal on it with the plug or install one without it? Also will it hurt to leave plugged in overnight?
View 13 Replies
If I leave my truck sit for a couple of days, the batteries are noticeably weaker. It's fine overnight, but two nights and it's slow to crank. Three and it won't start without charging the batteries. I checked for a drain last night and found that it was drawing 1.2 amps.
That seems like a lot, no?
View 14 Replies
Here is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 Replies
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 Replies
I have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
View 12 Replies
New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
View 14 Replies
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
View 14 Replies
I've got an E99 powerstroke. Recently it's been getting hard to steer, if not impossible. When I'm parked i can't turn the wheel and it gets better if i Rev the engine up, driving is usually ok and going around corners. It's just low speed, low rpm that it won't.
Also every once in a while when braking it feels like i lose all power brakes. The pedal goes to the floor and the brakes let go, then i can feel the pedal pump back up and i get a good feeling brake pedal again that actually stops well. All this happens within about a seconds time. But the steering is by far the worst.
I just did the power steering flush with atf and it didn't work. I'm thinking i need a new power steering pump, but want to ask here first to make sure. The truck has 290,000 on it, and it never has been replaced to my knowledge. I bought the truck with 147,000 however so it may have been done before that.
View 3 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
00' 7.3 is acting a little strange lately. i was towing a 15 foot trailer the other day for about 250 miles that wasn't all that heavy and my foot felt like it was very close to the floor. I had it to the floor and the truck would only go 60. now even without that trailer its better but still i feel as if i have to really put my foot down into it to speed up. if i go all the way to the floor in o/d it'll downshift and start speeding up but very very slowly then i run out of pedal and am at the floor, a lot slower than before. Before i wouldn't get to the floor and id already be moving pretty good. but now i gotta keep it pretty much 3/4 way down and keep it there to get up to speed and stay there. truck has 253k no tuner or programmer just 6637 intake and an exhaust, ww2. leveled on 35's. the tranny isn't slipping or at least doesn't seem to be. She doesn't shift perfect but its not anything crazy bad for stock with 253k on it. maybe something wrong with the actual pedal? or hopefully not but maybe the trans or motor , or maybe a sensor or something?
View 14 Replies
I purchased a 2000 excursion with the 7.3 a couple of weeks ago. The guy said originally in the add that it need #2 and #8 injectors replaced. When I went and looked at it he had already replaced them and said the it still has no power and needed the remaining 6 replaced. I purchased it as it was a good deal thinking I should be able to get it fixed for worst case a set of injectors. BTW the engine has little to no blowby and starts easy and idles great.
The problem it it will not build any boost (has external boost gauge). Actually the gauge only shows vacuum. With the truck in park or neutral you can slowly rev the motor to 2500rpm and all seems fine but as soon as you break past 2500rpm it sound like it is missing and starts blowing white smoke. The smoke smells like when a diesel heater runs out of diesel. If you try and drive it it has NO power and will not move out of its own way and will eventually start like it is missing and blowing white smoke.
The previous owner replaced the following:
#2 injector
#8 injector
UVC gaskets
MAP Sensor
Wastegate solenoid sensor
The first thing I did was start looking at the no boost issue and pulled the turbo. I deleted the EBPV while i was there. Also the turbine wheel was in very bad shape so i replaced the turbine wheel, shaft, seals, bushings and installed a new compressor wheel 5+5 wheel off ebay. Reinstalled turbo and the symptoms are the same. I also replaced the clamps on the spider with Tbolt clamps instead of the worm gear styles and it psi tested all piping and intercooler to 30psi with no leaks. Also the up pipes have already been replaced with the bellowed style so there are no leaks and it has a 4" straight exhaust.
I have since ordered oring kits for the injectors and also ordered the fittings for the fuel bowl so i can check fuel pressure. it has a new air filter, oil filter, oil and fuel filter installed.
The ICP sensor has oil in the plug but if i unplug it the symptoms are still there.
I have also used a scanner and the ICP pressure is approx 500psi at idle and the duty cycle is about 11% at idle. Also the HPOP looks to be new as it is very clean compared to the surrounding parts and i have checked the HPOP reservoir and it is full to withing 1/2" from the threads.
2000 Excursion
7.3
205000 miles
I am assuming that the injectors are original other than #2 and #8.
View 14 Replies
I have a F350 that has intermittent power loss.
View 14 Replies
OK . So here's the deal. My 2000 7.3 ford f250 170k miles. Going from phx az to flagstaff az . For some reason I'm hitting about 40 miles per hour with the pedal all the way down going up a decent grade. Seems like something isn't giving the motor power. I'm pulling a 28 ft toy hauler pretty much empty . Under 5800 pounds . What this could be . Also was get pretty close to the red on water temp gauge.
View 14 Replies
I have a 2000 7.3 I've been struggling to figure out why I do not have a lot of power below 2k rpm... The truck screws once it gets above 2k.
Assuming it was a turbo issue - I had the turbo rebuilt and put the wicked wheel in. Made a huge difference overall but truck still bogs under 2k.
No leaks in up pipes, they have been replaced recently. What the problem could be?
View 7 Replies
I have a 1999 7.3 with 260k miles. It is all stock with the exception of straight pipe. I got the truck about 8 months ago and have put about 5k miles on it. Have never had any issues with it. I was driving from Dallas to Houston and about 45 minutes into the trip my truck lost power. I was going about 65-70 mph and the service engine line came on and I lost power. It was running rough and was blowing white smoke. I let it sit for a couple minutes and started it back up and ran fine until 30 minutes later. It did this 2 more times on the way to Houston. Oil is good, coolant is good. Not over heating. Threw a code the first time but didn't throw it the other times. I brought it to a mechanic and he thinks it's the Wastegate.
View 14 Replies
