Ford 7.3L Power Stroke (1999-2003) :: 2000 F450 4x4 Transmission Slipping
Sep 17, 2016
I have a 2000 Ford F450 7.3 4x4 dully with a PTO driven winch 108,000 miles. The truck has develop a transmission slip.
I have changed the transmission fluid twice and it drives better but it slips badly. I can drive it up to highway speeds but it has problems getting from 0 to 10 MPH. The transmission runs hotter then normal but nothing major maybe around 205 degrees
Do I need a complete rebuild? This is a beater truck that I use to tow mainly. It is not worth a major investment. I need the PTO gear and 4x4.
I have several 2000 through 2003 7.3 E350 and E450 short school buses. Does the transmission from these has a PTO gear? I am thinking of pulling the transmission from one of them and swapping it.
It looks like the transfer case just bolts to the back of the transmission; I believe that a 2wd van 7.3 transmission will work with the 2000 F450 setup.
View 2 Replies
Advertisement
I have a 2000 F450 with a 7.3. I am having problems starting it. Batteries are good, engine turns over strong. It has started a few times after a extremely long crank (so long I am sure I am burning out the starter). I have replaced the CPS since it was cheap enough but that didn't make a difference. I have unplugged the ICP and it is very oily inside the connection. Does this mean the ICP should definitely be replaced? The truck will not start with the ICP unplugged. Should it be able to start with the ICP unplugged? Other items I plan on looking at at the IPR and possible the IDM box. Am I on the right track?
View 11 Replies
My tranny is acting odd. I put in drive and seems to slip a lot in 1st, barely even move at some times. If I put it in 1st with the shifter it goes in and grabs then I can shift up to 2nd or drive and there aren't problems. It drives normally when not from dead stop.
Transmission has 50k miles on it since replacement. Fluid level is normal. I don't tow and drive it particularly hard. I will have to go back and look at miles since last fluid change. I should be right around 30k miles since last change.
View 11 Replies
My son bought a 1999 F250 Diesel about a year ago. The seller gave him receipts showing that the 4R100 had been rebuilt and a new T.C. installed 25k miles before the sale. The problem is that it is slipping. He says it started with 2nd gear, now it will hardly move in 1st.
Fluid smells a little burnt. We pulled the transmission pan expecting to find lots of friction material. It does not have as much as I thought it would, not as much as I have found in the the pans of the few other auto trans I have seen with worn out frictions. Below are pics of the inside of the pan.
Or, is it the T.C. that is slipping. I have never had a vehicle with a bad T.C. How do you diagnose it? I have experience rebuilding (GM) Turbo 400's and 4L60's. Never had a ford AT apart.
View 3 Replies
I have a 1999 Ford F450 Tow truck with a 7.3 turbo. It loses power and misses when I give it gas but when driving normal speed no problems.
I had a ford technician look at problem with a computer and he said number 8 injector . Today number 8 was changed.
Test drove it same problem. I also changed th fuel filter. And I emptied the tank to make sure No water
View 4 Replies
i have a 99 f450 7.3 that cranks but will not start. I did an injector buzz test but it sais no communication between the computers. it has a new rebuilt engine, new ipr, icp, hpop, water pump, and both computers.
View 4 Replies
My VIN inside the door is scratched enough that the State can't verify it. They need two locations to match the VIN otherwise the vehicle must be scheduled for a "level 3" vin inspection hundreds of miles away. Well I tried to find one on the engine where the DMV can do a "level 2" vin inspection but I can't find it. Where other vin's are on my 2002 Ford 450. Mine is a flat bed.
View 4 Replies
I have a 2001 F450 7.3 chassis cab with just over 100k. I have a new problem... So far on two different occasions the service engine came on followed by a loss of power under a load and white smoke from the exhaust. Took it to the shop the first time, they determined it to be a dirty air filter, which seemed odd since it just happened all of a sudden. They changed air & fuel filter, problem gone- for two weeks..
View 8 Replies
I have 2000 F-250 7.3L when I start it up and push the brake it won't come out of park and when I push the brake the volt meter goes to 8 volts. If I shut it off and try again it is ok. Might take a couple of times of doing this then it's ok for a couple of days then it happens again. I've checked the connection on brake switch and everything looks ok. What to check next?
View 1 Replies
I have a 1999 f450 7.3 diesel that surges and will stall but will start right back up again and drive. It does this over and over but all ways gets back to the shop. The engine starts good when cold so glow plugs are working correctly. What I have done:
Fuel filter change, check electric fuel pump but have not replaced it. I have replace camshaft sensor.
What I have found d by inspection:
Throttle pedal has 2 electrical connections one for the IVS and one for the TPS. I have experience on the 7.3 IDI diesels but very little on the newer injection system.
View 10 Replies
2000 7.3 automatic suddenly went out of gear going about 30 mph wont go back into any gear, linkage checks fine, no slippage before problem, fluid seems normal good level not burnt no metal.
View 7 Replies
The truck is a 2002 F450 7.3 diesel with about 120k Miles.
While driving from 45-70Mph the truck engine stops for about 1 second and starts back up by itself. I thought the problem was the cps so I replaced it with a ford CPS. Today the problem still persists. The truck engine turns off and comes back on, the tach drops to 0 rpm and so does the speed.
The Check Engine Light comes on and so does the water in fuel light and so does the Check Gage light. After I turn off the truck and start it back up the truck does not show the lights.
I believe I found the issue, but can't look into it today. While I was moving some of the wires on the truck I found out that if I move the red/black bunch just a little bit the truck shuts off and comes back on when i let it go.
View 14 Replies
I was out with the F350, drw, automatic, 7.3, 4 x 4, yesterday about 30 miles from home base. The transmission started pumping fluid out the front like I have never seen before. I am not talking a drip, I am talking a stream, a big one..... almost like pouring coffee from a coffee pot. I noticed it when I was backing into unload and was leaving an oil trail, a quite obvious one.
We took off the tc cover as it was coming off that to find a dry tc and flywheel, but fluid running out off the case. This is the second time this trans left me high and dry in 165k miles. The first time was a stripped tc/ input shaft. We repaired the transmission then but I don't think we replaced much besides being sure no debris went though everything, fixed what was broken. That was about 25,000 miles ago.
View 8 Replies
I have a 2000 F250 4x4, it has been sitting in my garage for about 3 weeks. I cranked it up and backed it up about 10'. A few hours later I noticed a lot of transmission fluid on the floor. I remember hearing a hissing sound when I cut it off but didn't think anything about it. The fluid is on passengers side of truck, right side of the engine. Most of fluid is toward the rear but some ran down in front of the axle also. It's up high also, I've got fluid on rear of valve cover. I've cranked it up and let it run but can't get it to leak. Where did all this fluid come from?
View 5 Replies
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
View 11 Replies
I spoke with a few people here before about my 4r100.. it threw a code a month ago for P0750.. i replaced solenoid and it continued to do it even after clearing codes numerous times.. then all of a sudden it was perfectly fine for over a week, no codes, i ran a few brick hauls with it and ran it for over an hour straight.. i went to fl and upon return i took her for a drive and wouldnt you know, the code has returned.. i did hammer down a little but not from a dig, i just got on it a little playing with a neighbor and his truck and all of a sudden it did its thing slipping and not up shifting then the O/D started flashing again... i cant understand why the code would come back all of a sudden, there has to be a wiring problem correct?
View 9 Replies
Well, today i had my first bout with tranny issues of any kind either before or after my BTS installation. After sitting all day at work, heading home, the shift i guess from 2-3 at about 40-50 mph shifted really hard, BANG. Heard a whirring/whining sound, lots of slipping with the TC. After a lil ways it was like it was in neutral.
Coasted to stop. Went thru the gears from park, rev, and drive about 3 times, got movement each time. Got out, looked for obvious, no fluids or linkages apparent. Drove thru town about 25-30 mph. Felt like it was "hunting" and shifted like a manual grinding gears. Got on highway and no overdrive and im thinking no high gear either.
Push button on shifter light changes, but no change in operation. Running 60 and rpms are turning 2700ish. Still "hunting". But while hunting it isn't wide rpm swings, just a small amount, not wide enough for a gear shift. I am thinking that its torque converter constantly engaging and disengaging.
While letting out of gas it coasts down with TC still locked up all the way down to about 1100 rpm before unlocking. Then I start seeing the OD light flashing. Ok, classic wire chafe in steering column. But it doesn't always flash, only sometimes. And fuses are good. Temps never got above 150 during this 50 mile drive.
So i get home (and its frigging dark already, i hate that this time of year) and I log on and start reading up on this again to refresh my memory. I had called Brian over at BTS when it happened as i was going down the road, he was busy at time. He called me after i got home and i explained and he talked me thru some things. Wanted me to pull the codes and get back with him tomorrow. I did that and the screen shot is below. I will talk more with Brian tomorrow.
But during some of my reading i think i came across some others that had similar trans codes and the issue ended up being the alternator. Alternator ? For trans issues? Is that right? I guess stranger things have happened. I have a high output alt waiting to be installed but haven't yet. I guess we shall see. Brian thinks it something telling the TC and trans to act that way. Doesn't think anything mechanical, yet, leaning towards electrical.
View 14 Replies
My excursion's trans is slipping on the 25hp tune up high in the RPM band and shutters when up shifting. I have dropped to stock most of the time, but I know i am on borrowed time.
I had a JW trans in my e99, and there is no question on the durability and performance of the transmission. The price has gone up a lot, but that's maybe not the big issue.
I live in the mountains and spend a lot of time pulling and just driving in that 40 to 60 mph range over mountain passes. That is basically where I spend ALL of my time.
The distance between 3rd and 4th is driving me CRAZY! I have researched everything from swapping to a manual, to PCS controllers, to trying 4.11 gears, to overdrive units.
Swapping Manual: ZF6 is the obvious candidate, but I have read the swap is not probably something I have the skills or tools to do. I have also read that the performance of the ZF6 is sub par. But it seems like it would give me my 3.5 gear that I am looking for.
PCS Controller: Looks cool for a way to have control besides using the tree shift. Maybe a compromise on not swapping in a manual.
4.11 Gears: I get pretty excited thinking about the low end torque etc. I go off road almost every week, and like I said, I hardly go over 75 mph. But once in a while I do. Right now, the truck turns about 2300- 2500 rpm at interstate cruising speed. Looking for 4.10s rpm in that range to compare? Also, how bad of a fuel economy hit would I take? What is the cruising rpm of 4.10's between 60 and 65 mph, or in general what is the rpm change?
Overdrive Unit: I have always been interested in more gears, but I read about someone who installed one behind a 7.3 and didn't have they great of results. To the point where he said it wasn't worth it.
View 2 Replies
Hauled my last 2 cord of wood for the season, and I now have a pretty good 3-5 slip in and an intermittent bang/clunk when its shifting. So I've put this off for a long while now, and I want to fix it. I've done my research, and I don't really feel like I'm any further ahead than before I did my research.
I'm looking for recommendation's on what transmission and or kit is the best for my truck. I pull my 5er 10-15 times a year mostly up and down the east coast. We are looking to get a new 5er with a bunk house, my goal is to stay in the same weight neighborhood, I run 13-13,500 now depending on where we are going. The goal is to be able to get maybe another 3-5 years of use from the truck, maybe more, and then upgrade to a newer truck. So let me hear what you all recommend as I'm going crazy and probably over researching what I'm gonna do...as usual.
View 14 Replies
I own a 2003 Ford F-450 Superduty Chassis w/Utility Body. Owned it for the last 2-1/2 years . So far, the only things needing replacement were an Alternator, FICM, and routine oil and transmission fluid as well as filters.
This past week the truck started lurching while in traffic. I brought it back to the shop and put the scanner on it, and found codes for #1,#3,#5 injectors imbalance and no circuit to the fan motor. Did some research and found low oil and/or dirty oil could affect the injectors, I changed the oil and all filters also removed the EGR and cleaned it too.
I started the truck ran it, stopped, and restarted and let it run for a few. I cleared the codes and did another test. The only code that came up was the Cooling fan P0528 again. I let the truck run. All of a sudden the truck revved up and I could hear the turbo kick in and the engine seemed to take a life of it's own. I did another round with the scanned and found codes for Cruise Control popping up P0565 through p0569 and the p0528 again along with a p1000.
My truck is not equipped with cruise control, but apparently that is what might be making the engine surge. What do I do? What this might be???
View 1 Replies
Ive got a 2001 f-150, 5.4L, 121k miles. I've replaced the fuel filter, removed and cleaned all injectors, cleaned MAF, changed 2 faulty coil packs, and installed all new plugs.
No codes thrown, truck runs smooth. Problem is intermittent. It will act as though it's got no power, usually won't happen till it's warm. I can drive it for 2 hours, runs strong. Sometimes when I pull onto a highway and get on the throttle a bit, it starts to hesitate, rpm's go to about 3k and it hesitates, but does not miss. acts like trans is slipping but I'm positive it's not.
So when it starts to do this, it's constant. I can continue to drive and it's runs terrible, does ok if you barely use any throttle. But.... I can be driving 40-50mph while it's having this problem, toss it in neutral, turn it off and restart, and all the power is back, great acceleration, as if nothing ever happened.
View 3 Replies
