Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Noise Like Exhaust Rattle Or Vibration At Idle
Mar 6, 2017
I have a 2000 Ford F350 7.3 with the auto and 262,000 miles on it. As far as I know everything is stock on this truck. It has been a great truck but lately its been making a strange noise. It almost sounds like an exhaust rattle or vibration but it is intermittent. Its not really loud it can be heard best in the cab at idle. I've looked all over on the truck and haven't found anything. I can't pinpoint where it is coming from. I tried starting the truck with the serpentine belt off no change.
I took the inspection plate off the bell housing and couldn't see any cracks the torque converter bolts appear tight, and the starter is not engaged while running. I've read a few forums on the torque converter going bad. It looks to me like its more the 99 trucks that had trouble with that. Did the torque converter issue carry over to the 2000's? Would a torque converter/transmission problem be intermittent?
View 3 Replies
Advertisement
I change my motor in my 01 f350 ccsb to a forged rod one from a 97. When I put the thing in my inexperience cause me to screw up my torque converter in turn ruining my transmission. So after a rebuild I put it back in and she fit like a glove. Ever since I put the engine in i get a vibration at idle.
After I realize I screwed up the torque converter I figured that was the cause of the vibration. But now I know the trans is in properly I still have this vibration I'm thinking it's the position of the motor. I installed new motor mounts when I put the motor in but they were quite a bit off from the original points on the cross member.
My only idea to rectify this was to reinstall the original ones and try to position the motor back where it was prior to the engine swap. Or should I be looking elsewhere?
View 10 Replies
I hear a whoosh whoosh whoosh sound coming from the exhaust when its warming up in the morning. What is happening?
View 8 Replies
I have a 2000 F350 4x4 CC 7.3L 323,000 miles auto trans. I have removed my tuner just to make sure that it was not the issue. The truck will run fine then all of a sudden the idle will rise then fall or shudder or go up and down and sometimes it will just Die but it always restarts. No trouble lights at all. I am not sure what is causing the issue?
View 6 Replies
OK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.
View 14 Replies
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.
View 5 Replies
I have a 2001 F-350 w/7.3. There was excessive smoke coming from the exhaust. So the first thing I did was to pull the glow plugs to see what they looked like. and while having them out I cranked the engine over. Upon doing so I noticed 1 cylinder putting fuel out of the hole. Meaning it was like you could put your hand about 6 inches above the hole and your hand would be wet from fuel. None of the other cylinders was like that. So what I did was pull the injector from the cylinder next to it and put it in to see if it was the injector failing. But it was still doing the same thing. What would cause this??
View 3 Replies
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies
I recently upgraded my exhaust from stock to a 4" Magna Flow Turbo back kit. After the upgrade, I noticed a strange rattle coming from the tail pipe. It sounded like the pipe was vibrating on something but I checked and it is free from anything touching it. There are no strange noises coming from the engine area. it is only herd at the end of the pipe. If I start the truck it makes a the loose rattle noise like something is loose inside the pipe like the sound you get when you have a bad muffler. About after 4 or 5 minutes I hear the exhaust noise change pitch and make a whooshing noise like a gate or something opening or closing and changing the exhaust flow. After a while it goes away and make the loose rattle returns. The truck has lots of power and preforms great. Where to look?
View 3 Replies
So, I just got my turbo back from my pal Ruben at SoCal Porting (does good work fast and inexpensive) and, I have a question about the exhaust housing with the EBPV.
Is there a gasket that goes between the turbine housing and the adapter that the down pipe mounts to? And, if so, what is the part number for it? If it's steel to steel cool. If not, I'd prefer to put the OEM gasket in there versus permatex or something similar.
Pic of the compressor housing with a little port work....
View 3 Replies
I have a 2000 f350 manual transmission with electronic shift transfer case and my 4x4 won't kick on I've put it up on a lift and tried again but the front driveshaft won't spin and the light on my dash for the 4x4 won't work I'm also throwing 4 transfer case codes....
View 9 Replies
I need a wiring diagram for my 2000 F-350 power mirrors also to go along with the power window schematics that I posted before.
View 8 Replies
I have noticed a small vibration at 40-50 mph for a few weeks now and was unsure to the issue.. ( I just checked wheel bearing ect , last night ) . This morning at a stop light she started to white smoke shake and clack, somewhat violently, when I pull away from a stop it seems to smooth out and run normally.. A stuck injector ? Toast injector ?
View 11 Replies
Early 99 7.3. Runs ok has a slight miss at idle however every injector when unhooked makes a change. Has white and blue smoke From the exhaust. Has enough blow by to blow the oil cap off as your unscrewing it. My question is, I know engine restore is bad for these trucks but I can't afford to rebuild the engine. If I run the restore and then clean the IRP once the truck dies is this going to mess anything else up. Do you think it will by me a few months to save up for a rebuild
View 9 Replies
I have an early 99 F-350 with 268K miles. It is bone stock right down to the factory exhaust. A couple months ago I started have a rough idle and surging while driving problem. I never got a check engine light but I borrowed a scan tool from a friend and pulled the following codes: P1690 (wastegate solenoid), P0381 (glow plug circuit malfunction), P0269 Cylinder 3 Contribution/Balance Fault, and P0284 Cylinder 8 Contribution/Balance Fault.
I did some research and everything I read said it was most likely the CPS. So I changed the CPS. The truck ran fine for for a few days but then it started acting up again occasionally. I noticed that most of the time when it acted up was at start up when the engine was cold and I also figured out that if I shut the truck off and re-started it (sometimes I had to do it 2 or 3 times) it would clear up and run normal.
A buddy of mine that has a 2000 F-250 said he had a similar problem with his truck and it ended up being the ICP sensor. We switched his ICP with mine and I changed my oil at the same time (because it was due for an oil change). My truck ran flawless for over 2-weeks (over 200 miles) so I put a new ICP in my truck. Note: my buddy did not experience any problems with his truck with my ICP in it.
I've put about 700 miles on the new IPR and the truck has started to act up again. Once again shutting the truck off & re-starting it will clear it up and still no check engine light. I took it to a local "diesel specialty shop" while it was running rough and they hooked it to their scanner and got P1280 (Inj. Control Pressure Low), P1690 (Wastegate Solenoid Fault), P0381 (Glow Plug Indicator), P0269 Cylinder 3 Contribution / Balance Fault, and P0284 Cylinder 8 Contribution / Balance Fault.
They never did anything other than hook it to a machine & check the codes but their diagnosis is my High Pressure Oil Pump is going bad and my #3 and #8 injectors are going bad. They recommended I let them replace all 8 injectors and the High Pressure Oil Pump. The problem I have is they can't give me a REASONABLE explanation as to why re-starting the truck a few times clears up the problem.
View 14 Replies
I have a 2000 F350 7.3 ... A couple weeks ago I noticed that it was taking longer to start then it should be. Now I have to cycle the key switch 3 or 4 time to get it to start. There is a clicking coming from the relay block under the radio. Sometimes the truck will start sometimes it has to be rolled off. I have recently replace the starter and alternator. I have had the batteries tested and they are good. I replaced the two small relays in the block under the radio, one is for the fuel pump and the other I understand is for the door locks? I also read on here the large blue one is for the turn signal so I have not changed that one. After all this I still have the same problems.
View 9 Replies
2000 F-350 7.3L no gauges or throttle, I checked the fuses and no luck....
View 4 Replies
I'm looking at a 2001 Excursion with 242k miles. Truck is all stock, and everything checks out well. The only thing is there is a slight vibration at idle, that increases quite a bit when the engine is revved to about 12-1500rpm. Ran a CCT, and #8 was flagged. I know that can be somewhat normal depending on the CPS, right? Otherwise the truck is smooth, and in great shape. Should I be concerned about what feels like a slight miss on #8?
View 3 Replies
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 Replies
I have a 2000 with a six speed and through the first 2 gears while giving it only a little throttle, worse on hills and worse while towing I have a pretty decent vibration. Once you get to 3rd and up its fine. I have read about axle wrap and due to the fact my springs are pretty wore out I think this is a big part of it. Any other things to look at other than new springs? The u joints all look and feel fine so I haven't touched them.
View 8 Replies
2002 F350 single wheel 4x4, 280k miles chipped with a 6
My problem first started when the bottom of my sending unit broke off in tank causing me to run out of fuel at 1/4 tank. I dropped tank and repaired. A week later I noticed fuel dampness on my tank and discovered I crossthreaded cap on sending unit. About this time I started getting a shutter at slight acceleration only and a harder hit at idle. I thought air in lines so I dropped tank and reassembled. No air in line at all now but I still have a shutter so I replaced fuel filter in case of obstruction. No luck. Now since I have owned truck it has been a pain to crank in cold weather if it wasn't plugged in over night. It has been hard lately even in moderate weather since shutter started so I replaced both batteries today.
I replaced the ICP today also because I noticed the other day when there was oil on and around harness to it and when I unplugged it today the truck changed idle and there was oil inside. After I changed it I took it out and it still had the shutter and sound of a miss. At about 8 miles in it just died going down the road. I coasted to the side and it cranked right back up and drove home. The shutter doesn't fill as bad but there. Also I live in the mountains and on my way home after cutoff I had chip in Stock position and had to put peddle to the floor to climb hill. I've never had to do that. I'm getting worried I work for a living and caint keep throwing money at it aimlessly. I'm thinking at this point IPR or CPS. But I'm no mechanic so I could be completely wrong.
View 12 Replies
