Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Idles Fine But Runs Rough After Warms Up A Little
Apr 24, 2016
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.
View 14 Replies
Advertisement
So this is reason #345 why I should never have let my wife drive my F-350. I am in the Army, and I got a frantic call from my wife (I missed the first 7) saying that the truck died and won't start. I drive all the way to the truck, pop the hood and discover:
1) there is no coolant; and
2) there is no oil (actually just EXTREMELY low on both).
So, I do what any good Soldier does, I push the truck all the way back home (downhill mostly), buy 5 quarts of oil and a jug of 50/50 coolant, fill up both and try to start the engine.
The last time it ran out of oil (small leak on a seal that I didn't know about) in 2006, all I had to do was fill the oil, turn the key, and press the gas until it kicked over (don't judge me, I was a dumb LT). I did this again this time (now, I am a dumb CPT) but now it: 1) idles very rough; and 2) won't start unless I press down on the gas when I turn the key. There is no gauge light when it does this. I read the thread on the UVCH, but I am concerned I might have done something horrible to my truck.
2003 Ford F-350 7.3L
View 6 Replies
I have a 1999 Ford Escort SE wagon with 112k miles on it. Last week when leaving work my car started very rough. This was unusual so I killed and restarted the car about three times before letting it run it's course (~30 seconds), after which the car ran fine. About a week later on my way to work the car seemed to 'sputter' (for lack of a better word) when I pushed down on the petal looking for some power on two separate occasions. On each side of the sputters the car seemed to respond fine, but when it did sputter there was a severe lack of power. I got to and from work just fine, but while letting the car idle in the parking spot of my apartment for a minute before shutting off the engine the check engine light finally came on. The following morning the car again started rough (as if it were misfiring/running on 3 of 4 cylinders) and this time it took a good minute before smoothing out. However, after the car smoothed out I experienced no issues on the way to work, no sputtering, no loss of power, nothing. Doing some initial online research I feel that the problem may be one (or more) of the following:
-Fuel pump
-Vacuum lines
-O2 Sensor
-Spark plugs (they are original)
-Fuel Filter (it is actually past due for replacement)
I plan on getting this checked out ASAP, but that still may be 2ish weeks away with my schedule. Some similar reports say that I may be having a 'lean mixture' issue (not getting enough fuel), but I haven't had the time to check the code. My question is, how "safe" is it to continue driving my car with the current situation? Is it at a super high risk of failure/random stalling during rush hour? Will it cause any damage to the engine if there is a cylinder misfire upon start up? I was also wondering if the car would be reasonably reliable to drive on a ~400 mile road trip on an upcoming weekend, but I am making plans as if it is not.
Additional Details:-Tried charging the fuel lines (car to 'ON' then 'OFF' position 3-4 times), had no effect on the morning start-up-Commute to/from work is about 20 miles
View 13 Replies
I have a 2000 F350 4x4 CC 7.3L 323,000 miles auto trans. I have removed my tuner just to make sure that it was not the issue. The truck will run fine then all of a sudden the idle will rise then fall or shudder or go up and down and sometimes it will just Die but it always restarts. No trouble lights at all. I am not sure what is causing the issue?
View 6 Replies
I have an 03 F350 with the 6.0L. It has 210,000 miles on it and the injectors are beginning to be suspect. Its very hard to start when its cold, smokes and runs like crap untill it warms up.
I've found a set of injectors out of a 2005 truck with 8000 miles on them. The truck was overboosted and blew a head gasket.
Now finally to my question.....Can the overboost damage the injector? Would it be safe to buy these and install them or rebuild them before install or just leave them alone?
View 14 Replies
I have Warn hubs that I have to lock in. All works good. A/C goes to defrost at first when cranking but then runs fine after a couple seconds. So, I was thinking that maybe my pump is running all the time. Who knows. I'm sure all my vacuum lines are dry rotted. What exactly is the need for it exactly and what's the best way to cap? Hoping to do it at the unit itself if possible.
View 6 Replies
The car idles rough on cold mornings but runs fine. It will stall while idling but starts back easily. I am getting a 1131 and a 1151 code with my scanner along with 0300 and lean bank 1 codes. I started having these problems after I had to remove the upper intake to replace coil packs. I was getting egr code and had an egr port completely block off but cleaned that out and no longer get the egr codes. Spraying carb cleaner around the engine I get a very slight bump in rpm around a couple of the intake ports could that be my problem or should I look deeper?
View 5 Replies
It's a 99 f350 7.3 diesel powerstroke. About 180k miles I think.
It cranks fine. I just changed the glow plugs(all were dead) but when you try and start from cold, it takes about 7-10 seconds to fire. The oil res is full, tried disconnecting the EOP sensor, still fires up and takes just as long. There is one near the oil filter, and that seems to not be it either.
Doesn't smoke, no oil leaks that I know of. Not sure what else to check before sending it to another shop to get put on a diagnostics machine. I read about the IPR, but it has no problems when running. Only problem is a very long time to start. Also changed the fuel filter.
View 3 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 Replies
I have my 2002 Ford F250 Powerstroke. 175,000 original miles by me and only me. SCT, MBRP, Howes or Stanandyne almost always. Runs like new. It starts rough if I don't plug it in. Even on 50 degree days. Then it levels off and runs perfectly. If I plug the truck in I can drive off immediately with perfect operation of motor. I just went 1500 miles. Pulling a car hauler with car. NP at all.
New Glow Plugs, GPR "Yes it works", IPR, New Harness, Buzz Test shows it's fine, New #8 injector last year, New O rings HPOP. My buddy who is a PStroke guy said this trucks runs too perfect for it to be injectors. He recommends seals for the injectors. What does this mean. Or what else can it be. Where should I start.
View 9 Replies
I have a 2001 7.3 with 259,000 miles. It does not get too cold here, however over the past few winters when the temp is below 50 at night the first minute or two of running out of the neighborhood is tough going unless I let it heat up. It has been getting worse over the past few years and now if its even 55 or 60 I need to let it heat up. Glow plugs? Injectors?
View 3 Replies
2000 f350 CCLB SRW 176,000. I have a touchy accelerator. About two weeks ago the CEL came on and it wouldn't do anything but idle for about 20-30 sec then fine. Then it got a little worse. I disconnected the two harnesses on the accelerator pedal and sprayed them with electrical cleaner. Put it back together and it seemed to be ok. Today the pedal is real sensitive. Sometimes bogging down other times accelerating real high even tho my foot is pretty consistent and gradually accelerating. No CEL tho. Do you think I am in for a new pedal assembly? Could it be something else? UVCH?
View 13 Replies
Here's what I'm dealing with. Took the truck on a 1500 mile trip with no issues. Got home and started it the next morning and it started right up. 1/2 mile from home it starts to run rough and wants to die. It does this for a few minutes and then perks back up and runs fine for however long the trip is. It will always re fire and have no issues. Every morning it's the same game as described above. Within 1/2 from home it's doing this. Seems to be fuel delivery related, but why would it start after sitting overnight, and then after its little fit, run without an issue?
No codes in computer.
View 7 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
Quick back story I bought a 1999 Ford Ranger It is a 4 cyl with an auto trans the guy said it had some trouble with the tranny (major understatement) he also forgot to mention he cut out the CAT. so running a 4 banger off the header.
When you start the truck it rough idles but you have to hold the gas down til it warms up. You can shift into reverse but it labors the motor and the motor will not up the rpms kinda stays at idle and wants to die no matter how hard you accelerate and you can't move up a slight incline.
When you shift into drive you have to rev the motor to 3 grand an it will catch then move slowly forward. no matter how high the revs go. The fluid levels are a tad above the full level and a bit dark for my liking.
Ok, I used an OBDII scan tool from the parts store and it came up with 3 codes P0351, P0352, P0500. From my internet search the first two seem to be coil related which explains why the motor is running like garbage. The last may or may not have to do with what the tranny is doing.
View 2 Replies
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 Replies
I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......
View 9 Replies
On a cold crank the engine idles rough until it warms or the accelerator is pressed down. Also runs rough going up hills or towing. Check engine light is on and is throwing the code for bank 1 to lean and cat performance below threshold. Cats have been tested, good. Fuel trim tested, good. One mechanic said noth8ng is wrong with it well, there is. 2011 f250 6.2 gas...
View 5 Replies
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 Replies
I have an early 99 F-350 with 268K miles. It is bone stock right down to the factory exhaust. A couple months ago I started have a rough idle and surging while driving problem. I never got a check engine light but I borrowed a scan tool from a friend and pulled the following codes: P1690 (wastegate solenoid), P0381 (glow plug circuit malfunction), P0269 Cylinder 3 Contribution/Balance Fault, and P0284 Cylinder 8 Contribution/Balance Fault.
I did some research and everything I read said it was most likely the CPS. So I changed the CPS. The truck ran fine for for a few days but then it started acting up again occasionally. I noticed that most of the time when it acted up was at start up when the engine was cold and I also figured out that if I shut the truck off and re-started it (sometimes I had to do it 2 or 3 times) it would clear up and run normal.
A buddy of mine that has a 2000 F-250 said he had a similar problem with his truck and it ended up being the ICP sensor. We switched his ICP with mine and I changed my oil at the same time (because it was due for an oil change). My truck ran flawless for over 2-weeks (over 200 miles) so I put a new ICP in my truck. Note: my buddy did not experience any problems with his truck with my ICP in it.
I've put about 700 miles on the new IPR and the truck has started to act up again. Once again shutting the truck off & re-starting it will clear it up and still no check engine light. I took it to a local "diesel specialty shop" while it was running rough and they hooked it to their scanner and got P1280 (Inj. Control Pressure Low), P1690 (Wastegate Solenoid Fault), P0381 (Glow Plug Indicator), P0269 Cylinder 3 Contribution / Balance Fault, and P0284 Cylinder 8 Contribution / Balance Fault.
They never did anything other than hook it to a machine & check the codes but their diagnosis is my High Pressure Oil Pump is going bad and my #3 and #8 injectors are going bad. They recommended I let them replace all 8 injectors and the High Pressure Oil Pump. The problem I have is they can't give me a REASONABLE explanation as to why re-starting the truck a few times clears up the problem.
View 14 Replies
