Ford 7.3L Power Stroke (1999-2003) :: 2000 F250 Shut Off And Would Not Start Again
Sep 23, 2015
I have a 2000 f250 7.3 with about 230,000 miles on it. So I filled my truck up to go out of town got on my way drove about 50 miles and the next stop I made the truck shut off and would not start again. I figured CPS went out again! nope changed it still not start. So check the fuel pump seemed fine was getting diesel. Checked oil, was a little low so i topped it off nothing. So i left the truck over night and came back on sunday still nothing. I finally got it started with a shot of quick start i know its not good but i had to get this Truck home. I drove and made it almost home took my foot off the pedal and it stalled again so i pulled it home. Had a guy go over and scan it and it says the oil pressure is at 30 psi when cranking so he says the hpop is probably bad.
View 2 Replies
Advertisement
I have a 99 F 250 7.3. It runs fine at idle even for a long time. When I drive around the block a couple of times it will start chugging and lose power and shut off. I have been mixing fryer oil with the diesel. I changed the fuel filter, oil change, crank sensor and fuel pump. I added 15 gallons of diesel and diesel treatment. Pulled fuel filter and bowel is full I'm not sure where to look next.
View 1 Replies
I'm having issues with my girlfriends truck turning over. It won't turn over at all. I'm not getting any power to the small wire on the relay on the passenger fender or the red wire with a blue stripe off the ignition module.
I've cleaned and tested the batteries and the terminals. I've replaced the ignition switch the ignition module the starter and the starter relay on the passenger fender and I've also checked the neutral safety switch. I've checked all the fuses and relays also.
It's a 2000 Ford 7.3l automatic.
View 13 Replies
Cooler weather has arrived and my 2000 f250 won't start. Wait to start light is coming on, no power passing through the two relays on top of the engine. Are both of these for glowplugs? My 97 only had one. How do I diagnose relays on this truck? If you cross out the two relays truck fires right off so I know the glowplugs themselves are good.
View 7 Replies
I have a 03 f250 6.0 had it for 2 years never had a problem. Last week I went out and started it to warm it's up as it is cold out here and it started fine I then noticed some thing hanging down under the dash so I started tucking it up under there and it arced and all gauges shut off and the truck shut off. So I took the panel down and it was the biometric pressure sensor that was hanging and the previous owner had a remote start on there that I never knew about and 2 wires on the sensor were stripped and not taped as well as some others. I checked all fuses and relays all working good tested fuse box and everything good there, replaced bio sensor and still nothing turn the key and try to start it and it does nothing injectors, don't precycle fuel pump doesn't run and starter doesn't kick in. I jumped starter off the wire on fender and it turns over but still doesn't start. Also I think it's the ecu but don't want to buy another one if I'm not sure if that's the problem.
View 7 Replies
Truck is an early 1999 F250 Super Duty ext cab long bed, ZF6 swap. 164k miles on the dash, has the newer injectors and hpop from what I was told. It does have a 6 position switch, I typically keep it at the daily 70 horse gain tune. I do not beat the truck often. I don't tow often either.
Truck always took a few seconds longer to start than other 7.3s I have seen. So two days in row, after 8 hours of sitting in the sun, my truck did not wanna start right. Took about 5 minutes of cranking both days to get it to start. Then today on my way to work in the morning I started truck let it idle, everything seemed fine, Started driving and the engine just didn't sound right, but I figured maybe it was still a little cold. Continued driving, and it stalled out ( zf6) , I tried pop starting it but that only got me another block or two, after 10 minutes of cranking I got it to start up made it a half mile it shut off, same thing started and got it home. It cranked longer than normal but started at home after it I turned it off.
At work now so I have yet to check anything. Replacing CPS after work No smoke out of tailpipe, It is getting fuel, I checked the filter. I am no master mechanic, I do basic maintenance like oil changes, brakes, filters and censors my self. Anything more intensive I have not done. If it is not the CPS what else could it be, and how would I go about checking?
View 7 Replies
Shortly after i bought the truck and started driving it home, it shut down on me while coming up a mountain on the interstate. I had probably drove it about 10-15 miles and about 20-30 minutes of running after being dead cold. The temp gauge was about in the middle and it would not start up again until about an hour and a half later, which I was able to drive it home another 20 miles away.
There are no codes, which a mechanic told me it is probably an intermittent problem then. He then told me it would either be the cps, ipr or fuel pump. I have changed the cps and since then have not been able to replicate the problem but I have also not been able to get the engine up to temp because of the recent weather being so cold. I want to test the truck and see if I can get it to stall again but what this could be or what I can do to test the truck?
The truck is a 2003 f250 7.3 4x4 automatic, short bed, crew cab, with 320k miles.
View 8 Replies
Have no OD, when you press the OD button nothing happens and then the OD light flashes until she's shut down. On start up no flashing until OD button pressed. All other gears shift lovely. Haven't checked codes yet.
View 9 Replies
My truck is an 02 F250 7.3 with 280,000+ miles on it, so I wouldn't be surprised if I might have a number of things going wrong. It runs pretty good, but is still far from 100%, at least up to my standards. So the problem has been going on for the last two or three weeks and got worse today, and there were a few things leading up to it as well. I'll start off with the first thing that happened that I think might be related. It was about 6 months ago, my buddy and I were putting my new headlights in.
It was parked in his garage and we backed it out a little bit to try and adjust them. It was sitting there idling for a minute or two and just shut off or almost stalled out. Tried to restart it and it wouldn't start, tried multiple times to no avail. It acted similar to when I had glow plug troubles when I first got the truck, it would just crank and crank, but never actually kick over and start, along with putting white smoke out the exhaust. Ended up waiting about a half hour and then the truck fired right up with no problems after that, so I didn't think much of it.
Then fast forward to last week to when something similar happened. Started it up after sitting for a few days, started right up, idled for a few seconds and then just shut off. Started it back up ran for a second and died again. Tried a third time with the same result. Fourth time fired right up again and stayed running, let it run for a few minutes and was fine. Also along with this, there was a bad squeaking coming from the front of the truck, like what a belt would sound like. I have recently replaced the belt because it was squeaking and actually got chewed up and almost shredded completely apart.
So not sure why it is squeaking again, but not sure if this could be related or not. Then took it back to my dorm room to get my stuff, and then made it the hour or so drive home from school, without issue. Even went to a few stores before I went home, and shut the truck off and started it back up multiple times, again with no issues. When I drove back earlier this week it was fine until I got there and put it in park. It idled for few seconds and then cut out for a second, but then idled back up and continued to run fine. It has done that a few times as well. So it will do it on a cold start or after already fully warmed up.
Then it got worse today. Again had trouble starting it cold, same as what I explained early. Except second time cranking it wouldn't start at all, then on the third crank it started up and stayed running. But on the drive home is when it got worse. About 5 or 10 minutes into my drive, was just cruising doing at about 45 or 50, and truck just shut off, died/stalled out. It cut out and shut off for a second or two and then started itself back up and continued on like nothing happened. It scared the crap out of me the first time it happened, I was waiting for something like that to happen, but still wasn't quite ready for it.
The truck acted just like it would before you start it, with the key on, dash lights worked and the radio still worked. It did this 4 more times in similar ways, would die and then start back up, at various speeds and at roughly 5 or so minute intervals. I decided to just keep going as long as the truck would start and stay running, hoping to make it home. It did it a fifth time and this time the truck completely shut off and wouldn't restart itself. It was hard to see, as I was watching a few different things at one time, but I think it tried to restart, I noticed the tach bounce between 200-400 RPMS and then die. So I had to pull over and then restart it, fired up and drove fine. That was about half way home, and I made it the rest of the way home without any more problems.
So obviously I'm wondering what would be causing the truck to do this? I've done some reading and have a couple ideas, but not really for sure on anything. I was thinking maybe the CPS, I think it can cause a no start issue. Could ICP or the ICP sensor have something to do with it? I was also thinking maybe something fuel related, such as fuel pressure or a bad fuel pump. Any of those sound to be on the right track?
I have the torque pro app, but not exactly sure how to use it yet, and also just got access to my Uncle's Snap-on scanner, so I ran some tests and pulled some codes. How to more utilize these tools in diagnostics. I did get a few codes, but I'm not exactly sure how they might be related. The codes are pulled are:
P0470 Exhaust Pressure Sensor Circuit Fault. Just cleaned that out as well as the tube about a year ago, but I guess could be clogged again or has gone bad.
P1274 Cylinder 4 (E) High to Low Side Open. Did some reading and figured out that this could be UVCH related. At the same time, about a year ago, did new injector O-rings as well as all new Motorcraft UVCH's, so can't imagine that one is bad. Or that one could be loose, I would have guessed it would have happened more when I first did them, not a year later, but who knows.
Also pulled P1876 T-Case 2wd Solenoid Circuit Fault. Not sure if this is related at all, but also not sure what it means either. I read that it could be ESOF system related, which I do have, but I have manual lockout hubs, so maybe that's why it throws the code.
Also a few things that may or may not be related, but I think worth noting. Ever since I've had the truck the check engine light will pop on and off sometimes. It will do it on a cold start or, when I first start driving and its not fully warmed up yet. It does it most when the engine is still cold, and it almost never comes on once the truck is fully warmed up, but has came on and off more frequently lately. When driving, it will only stay on for a few seconds and more often when I'm lugging the engine or at lower rpms, and will commonly shut off if I let off the throttle.
I don't think it really comes on at higher rpms. I also have a slight oil leak in the valley of the engine, seems to maybe be coming from the front of the motor. Nothing too serious, leaves a small puddle where I park, loses enough to be at the add mark, a little before an oil change. Changed the oil about 1500 miles ago and have been able to notice a slight drop in oil level. Also I have changed the fuel filter in the last 500 miles.
View 9 Replies
My truck occasionally gets a hot no start issue and it's been happening more frequently. Mostly it happens if I drive it up to operating temp turn it off for a short time, then try to start up again. Usually, if I wait 15min to an hour it will start up. It has died on me while driving too, then I have to wait and periodically try it. I've noticed in this situation that if my glow plugs turn on for only a short time, it won't start. But once the motor has cooled enough that the glow plugs stay on for the longer duration, then it will start right up.
I've replaced the CPS, rebuilt the IPR, did the ICP unplug test, rebuilt the injectors, replaced the fuel filter.
HPOP oil level is good, changed the oil maybe 500mi ago. When it's a no start, the low oil pressure gauge does start to read after some cranking, also the tach does read. It throws no DTCs. My reader isn't able to monitor live sensor data.
There is some oil in the valley, but I can't find the source. I think it's probably the turbo pedestal. What else should I check?
View 14 Replies
I am a new and very happy 7.3 owner. i have lurking around these forums and decided I didn't want to be a creeper anymore. So onto the fun stuff.
Yesterday my wife was exiting a freeway and the Ex shut off while exiting. once she came to a complete stop she tried turning it on and it would start then immediately shut off. she was able to turn it on and it would run then shut off as she drove across the intersection. once she made it across a good samaritan offered to park it for her. She noticed a little bit of black smoke but she told me that the guy was revving it to keep it running.
Luckily there was family at the mall and she waited for the flat bed to arrive. it sat for about 2 hours and they tried starting it and it would start then die. no more black smoke though. we had it towed to a diesel repair shop and they went to start it today and alas it started right up. they let it idle for 30 minutes and it was good. they test drove it and all good. they ran the codes and got the following:
P1876
B1352
B1483
U1147
One thing I did notice a couple of weeks ago, while driving on the freeway cruising about 65, the Ex surged a little and then ran fine. then another time it surged a little while idling. Some more info on the rig. it has a banks six gun tuner and has a cold air intake and exhaust. And it has a Banks Big Head wastegate. I bought the rig 2 months ago and changed all the filters and fluids.
View 6 Replies
OK . So here's the deal. My 2000 7.3 ford f250 170k miles. Going from phx az to flagstaff az . For some reason I'm hitting about 40 miles per hour with the pedal all the way down going up a decent grade. Seems like something isn't giving the motor power. I'm pulling a 28 ft toy hauler pretty much empty . Under 5800 pounds . What this could be . Also was get pretty close to the red on water temp gauge.
View 14 Replies
I've developed a problem, usually when starting, that the truck will crank over, start and idle for a few seconds and then shut off. The few seconds it idles it doesn't get any throttle input. I'll crank it back over taking a little more than usual to get it started. When it does start it seems slightly sluggish but that quickly, like almost immediately goes away and the throttle is working again.
Oh, 2001, 7.3 stock w/200k
View 1 Replies
I've got a 2000 F-250 with a 7.3. The other day I was driving down the road and it lost power and my foot almost went to the floor. I was at the bottom of a hill when it did this and I was running 60 mph. By the time I got to the top I was running 20 mph and had the truck to the floor. When I was driving it home it was tacking around 1800 rpm and my egts were only at 125 degrees. I know I'm not getting fuel. I thought it could be the fuel filter so I changed it. Still no luck. It'll start back up but it dies if I take my foot off the accelerator. It shook terrible when I was driving it home too. Is it injectors, uvch, hpop, or something else?
View 14 Replies
I am fairly new to powerstrokes, but have a general understanding how the 7.3l operates, and how the fuel system works.
The problem i am experiencing is a crank, no start. The truck has been great for the year and a half that i have owned it. Always cranked great and never any starting or running issues. One day upon cranking, i started the motor; it started normal running good for a minute until the motor suddenly started shuttering and then the motor shut off, happened rather quickly. The truck started up immediately after that and died....repeating the shutter until dead. Now the truck will not start.
Specs on truck:
2002 7.3l
230,000 miles
Manual transmission
Here's what i have replaced so far:
New parts include:
IPR (motorcraft)
ICP (motorcraft)
EBPV (napa)
CPS (napa)
IDM (reman)
Here are some of the diagnostic values i have collected during cranking: (FYI: i am a little confused on what the values mean and what they should be in order for the motor to start):
ICP: 2218 psi
ICP duty cycle: 41%
EBP: 265 kpa
battery voltage: 12.0
Rpm: 355
Things i have checked so far:
Oil is new and level is good.
WTS light cycles as normal.
Fuel bowl is full and over flows with cap off while cranking.
Fuel tank is above half.
Glow plug relay is good.
I was throwing a code for the PCM, but i removed the bully dog tuner and the code has since cleared.
HPOP oil is an inch below full.
I made a gauge set and dead headed HPOP yielding 1500psi.
Upon cranking i am seeing some smoke, i guess, but its kind of hard to tell from the drivers seat.
This is where i am at so far. I don't have a way to buzz test the injectors or tell if they are leaking past the orings. I have the valve covers removed, but i have been putting off pulling the injectors to replace the orings.
View 14 Replies
I have a 2000 F-250 7.3 L Diesel w/200,000+ miles on it.
I use the truck for snowplowing and last snowfall one of my employees broke the overdrive switch on the PRNDL shift lever. I just replaced it and as I went to start the truck I had just turned the key to run in order to let the glow plugs warm up and the truck attempted to start itself.
As it was running I could hear the starter continue to run although I never fully turned the key. I have since then replaced the ignition switch and the key lock cylinder. That didn't fix the issue, I then pulled the fuse box that is inside the cab of the truck to inspect the GEM module. Other than lots of dust there was no corrosion or any see-able issues with the module. I cleaned all connections thoroughly and even applied a little dielectric grease to the connections.
Still has the same issue, I ran a voltmeter to the trigger wire on the starter relay and it reads 10V when the key is turned to run. I believe it should not read any voltage until the key is turned to start. If I have the trigger wire on the starter relay disconnected the truck won't start, obviously. I don't believe the starter relay is bad because it does start only when the key is in the run position and it has never attempted to start without the key.
View 9 Replies
I have a 2000 F250 7.3L and I pulled this from the overflow tank. I'm thinking it's oil since my oil cooler is leaking but just want to make sure it's not fuel and need to do injector cups...
View 2 Replies
I just bought a 00 f250 cc that originally came out of Canada so the speedo and mileage is all in kilometers. I have bought a use cluster that is in standard units to replace it with. I am just curious if all I have to do is replace the cluster or if there is other thing that need to be replace as well to make it work right.
View 12 Replies
So I'm not sure if I should post this here or in the 1994.5-97 section. The reason being I have a 2000 f250 with a 97 7.3. It currently has a mechanical fuel pump but they keep crapping out. We dont have the money to do a $600 diy conversion so were looking for a cheap solution.
So the 2000 has all the fuel lines and plugs to put a electric fuel pump in, but if I just threw a electric pump on then it would feed to the mechanical fuel pump which I'm guessing is a no no? Or possible?
If I put the electric fuel pump would I just have to remove the mechanical fuel pump and run lines from the pump to the bowl?
If the fuel bowl can't hold the pressure of an electric fuel pump then would I be able to swap the fuel bowl only and be good to go or is that impossible?
Let me know what you think were trying to do this as cheaply as possible.
2000 f250 auto 4x4, 97' 7.3 motor.
View 4 Replies
I have a 2000 7.3L f250 superduty. after rebuild and a yr now have engine smokes when you rev the engine and an imbalance on No1 cylinder causing injector to carbon up poss from prev misfires due to injector harness now solved? Found the turbo exhaust outlet pipe leaking oil we think because the wrong size clamp fitted. will fit new clamp tomorrow but if this does not solve problem what next? This has now cost thousands and still having problems...
View 14 Replies
I have a 2000 f250 with the 7.3 and 181,000 miles on it, recently got stuck in the snow (in 2wd because i forgot to lock the hubs) and the rear wheels did alot of spinning. Now i randomly have the OD light start to blink, sometimes its a half a blink, sometimes it'll stay on for a few seconds, itll do it randomly while crusing down the road at a constant speed, also noticed my rpms fluctuate a tad at idle.
View 4 Replies
