1994 f250 7.3 turbo problem.. runs great on the level.. Cruises 65 no problem.. We have an 8% grade coming from town and half way up it starts cutting out and sounds like a jack brake under the hood and loses power.. Once over the top it clears out and runs fine again.... I just changed the fuel filters but no luck... I have been wrenching on cars all my life but no diesels..
View 6 RepliesI will start with what I have done to my truck. Hutch and harpoon mod, fuel pump, new orings on fuel lines, fuel filter, air box, 4" exhaust. My issue only happens when my engine is warmed up and I put it under a load(driving up a long hill or pulling up a long hill). My truck starts to shudder and feels like missing until it looses all power to where it won't even pull itself and will just barely idle. It doesn't die though. I watch the engine oil temp and it seems to be around 195-200 when it occurs. I can turn the truck off and let the oil temp cool to 150-160 and then start the truck up it will miss for a second then clear up. I will start driving again and it seems fine until the oil temp gets up and start putting it under a load. I have read many posts and can't figure out exactly where I need to start. Some of the codes I pulled are P0603, P0470, P0732, P0542 and P1211.
View 14 RepliesJust picked up a 99 F250 7.3 Stroker, it had sat for two years in a warehouse, the truck had just had reman injectors put in right before it was parked. We fired it up, and it was missing, and smoking a lot (light blue, almost white) I checked the oil filler cap, and no water on it, after it ran for a while, it stopped. Shut it down, went and got my trailer ready to load the truck, fired it up, and no smoke to speak of, by the time I got it to my trailer, still no smoke.
I revved it against the governor a few times, hoping to clear the miss (figured may have been trash, or a sticky injector from sitting so long) It is turned up pretty good, as it came with a Superchip Super Tuner. It seems to hit on all eight above 2500 RPM or so. Brought it home, and took it out on the road, it seems to only miss under 2500 RPM or so. I took of from a dead stop, then got on it hard at about 15 to 20 MPH, it took of nice, then all of a sudden, the tach started climbing like the trans was slipping, looked in the mirror, and the tires were smoking, guess they broke loose when the boost came in!
I let it idle and warm up for a good half hour and noticed a lot of pure white smoke coming from the exhaust, went back to it and it was steam, I took the oil filler cap off, and there was a lot of steam coming out of there, pulled the dipstick, more steam, I then noticed the degas bottle was low, I topped it off, and got in the truck, and revved it a few times, then held it at 2500 RPM for about a minute, It started blowing water out from under the degas bottle cap. I called the guy I got it from, and he did NOT put new injector sleeves in when he did the injectors, I don't see any oil in the water, but there is water getting on the oil filler cap now! Does it sound like a head gasket, or an injector sleeve?
1999 F250 7.3 .. The truck seems to idle fine and and runs smooth all the way up top cruising speed, but when it levels out at say 65mph then it starts missing and jumping. I can ease into the throttle a little and it smooths out up until it levels out again.
I have the Vgate Elm and Car Guage Pro and a couple of other apps and the only DTCs I'm getting anymore are:
P0541 Intake Air Heater Circuit Low
P0640 Intake Air Heater Control Circuit
But from what I've read, neither of those should cause this issue.
Buzz test sounds good.
Cylinder Contribution test throws code for #4 Cylinder
I'm trying to do everything possible before throwing an injector in it.
I have a '99 F250 SD 7.3 & im going on a trip next weekend so I thought I'd pull the exhaust pressure sensor & clean the tube in an attempt to get better mileage. Found the sensor & unplugged it. Went to the manifold & started removing the tube when it fell off. 6" from the manifold it's broke & the rest is completely missing.
Autozone doesn't carry this tube so, how important is this sensor?
I have a 1999 Ford F450 Tow truck with a 7.3 turbo. It loses power and misses when I give it gas but when driving normal speed no problems.
I had a ford technician look at problem with a computer and he said number 8 injector . Today number 8 was changed.
Test drove it same problem. I also changed th fuel filter. And I emptied the tank to make sure No water
The last couple of days with the temps in the 50's, my 2000 F550 with a 7.3, will start normally and idle fine. When I try to drive it, I get less than a quarter mile and it just looses power and will die.
If I flutter the pedal, sometimes it will keep running, very poorly. And when it does this, it is putting out blue smoke. After it does this, it will run fine. Just like nothing is wrong.
What do I look for, or is this normal. I have had the truck since last October and this is the first time it has acted like this.
I am a mechanic and tow operator running a late 99 f350 7.3 6 speed cab and chassis wrecker. This truck has had a hard life and has been neglected for quite some time, and now has become my baby/headache. Truck starts great, idles nice, and will run great for about 5 minutes until it starts billowing white smoke that smells like fuel and loses all power. If you continue to drive it it will die. Sounds like it's dropping cylinders and will barely idle. If you stop for 5 minutes or so and let it idle it will smooth back out and will run great again for another minute or two, then right back to stumbling.
Using torque app, hpop pressure looks good when it's running well. Peaks at 3k, IPR maintaining 30-40% max. As soon as it stumbles you can see the hpop drop to 5-600 and the IPR will climb to 65%. Let it idea bit and they go back to normal, and stay good until it stumbles again.
Ive changed the fuel pump, ICP,rebuilt FPR, change fuel filter, pulled and cleaned the fuel tank (metal tank, no delamination, looks perfect inside). Pickup screen looked good. Cleaned the IPR, cleaned the hpop reservoir, there was no screen inside. Checked voltage at fuel pump, 11.78 across the pump with it running. Pulled valve covers, no noticeable leaks around injectors. Injectors have less than 5k miles. Remans with 100% larger tips.
To me it seems like the lpop is not keeping up with the hpop under load, starving it until you idle and let it catch up. Could it still be bad injector orings? Bad lpop? Something I'm not thinking of?
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 RepliesMy 02 excursion is missing at idle and jars the whole truck around going approx 50mph feels like good amount of power loss but still pushing 30psi boost, just got autoenginuity all injectors buzz fine on the test, contribution test show balance fault in cylinders 1&8, should I look for o-rings to be bad, uvch, cups cracked or what ----- turbo fine, hpop great condition, new IPR, new fuel pump and hutch mod, about. 250k miles on truck nothing else major showed up on ae.
View 5 RepliesI have a 2001 F450 7.3 chassis cab with just over 100k. I have a new problem... So far on two different occasions the service engine came on followed by a loss of power under a load and white smoke from the exhaust. Took it to the shop the first time, they determined it to be a dirty air filter, which seemed odd since it just happened all of a sudden. They changed air & fuel filter, problem gone- for two weeks..
View 8 RepliesWe have replaced 4 fuel pumps on a row.
Voltage is good...even ran a fresh circuit.
Ran new supply lines
But, can't seem to understand the continued drop in pressure. It usually takes about a day of driving to crater after a new pump/filter is installed.
It never dies, just loses power and drops the truck to an idle. Funny thing...if I shut the truck off and turn it right back on...full power for a short period!
The truck is used on a ranch that has plenty of rough roads...thought inertia switch maybe but i believe that would stop fuel completely right?
I am totally stumped and so is the mechanic.
I have a 2000 F350 7.3 213,000 miles. Manual tranny, 2wd. It is my daily driver.
No issues until 2 weeks ago I pulled out and began shift gears when the engine died and I completely lose pedal. The engine does not shut off it goes to idle and the lights and power are fine but I quickly lose acceleration. After a couple seconds and a few pumps on the pedal it comes back. The problem is intermittant. Until yesterday it was only in the morning but then happened on the way home from work. Thinking ti was water in the fuel I used an additive to cure the water.
I changed the fuel filter just after I bought it in April of this year. I know there is a Injector Pressure Sensor that could be the culprit. EGR?
I have a 2012 F-250 6.7L w/8K miles. I have been struggling with this issue for 6 mo. The engine feels like its missing at low RPM. I would equate it to the feeling of a bad coil pack in a gas engine. The boost indicator drops to 0 for a split second then recovers. The dealer says they can't find the issue but went ahead and replaced the turbo. After the turbo replacement It got worse. This is an intermittent problem with no codes.
View 14 RepliesBeen fighting a coolant issue on '02 F250 4x4 with 7.3. Truck runs hot when under load (ie towing, or ac running on a hot day going down the road). Will sit and idle all day with ac on high and 100 outside. I hear my fan at cold start as normal but that's the only time I hear it. Still has original water pump, fan clutch and radiator. I know all three could stand to be replaced with 340,000 on it. But can't afford to do it all at once.
View 14 RepliesFirst off I have a 2001 7.3 with 294000 miles. While pulling my camper after it gets warm it puts out a very loud whistle it seems to happen when the fan clutch kicks in it does not sound like a belt squeal it almost sounds like it's coming from the turbo area. The engine seems to Surge while this is going on but the RPM gauge doesn't dictate that it almost sounds like it's the fan clutch surging. I took a short video of it while it was doing it ...
View 14 RepliesI have a 2002 7.3l with 229k miles. So I am having a big problem now missing oil! My reservoir is empty and my dip stick is reading low, and i just put 16 quarts in yesterday with the new filter! im having a long start issue obviously because i don't have any oil supply! just drove the truck today, ran great been having this issue for the past week. here are the details. i came up from Texas after installing joeys t500 pump, when i arrived to California there was oil everywhere! my pump that joey rebuilt had an issue so he sent me another and bam! runs great no probs, now after about to weeks and about 15 degree temp drop i get hard starting. first time instead of a 2 second start up it took 9 seconds, now it takes anywhere from 9-20 seconds to start! so after my drive today i let it sit for about 3 hours seeing if maybe i had air in the lines from the res not being full, well now i cant get a start at all my res is empty and my dipstick shows little oil, i just replaced the icp. ipr, and eot when i put the first pump in, could this be the lpop?
View 14 RepliesI have been having a problem for a while now where my truck will miss/buck at WOT. This only happens at higher RPM's. From a standing start 0-60 it is fine. However when I downshift full throttle from about 50 MPH it initially goes, but then it will miss/buck consistently until I back off the throttle.
I have so far replaced the CPS, re torqued injectors, checked valve cover harnesses and fuel pressure stays in between 64-58 full throttle. No codes show up.
My truck runs great except as I described above. I would think an injector or two are bad, but the truck runs and idles great. My initial guess was that it was a fuel pressure issue, but fuel pressure holds strong. Could it be air in the fuel?
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
The issue: when I reach 37-40mph I have a new sound which I believe is the transmission 4R100. It sounds like a flat spot on a tire, or the sound tires make when they leave the sticker on them. The cadence of the sound is slower than the rotation of the wheels.
If I let off the accelerator, the sound stops, as soon as I add load by pressing the accelerator the sound returns. If I shift to Neutral the sound is gone.
If I coast at any speed the sound is gone. It is only audible when under load at speeds above 37-40 mph. The cadence does increase as I speed up, but it doesn't sound as fast as the motor is turning (~1900 rpm's).
I monitor the truck with torque pro using the PIDs defined here on FTE. I can see lock-up in 3rd and the shift to overdrive. When in lock-up, I see 1-7rpm TCSlip.
Watching transmission temp as reported by torque, the hottest I see is 183* pulling an enclosed 6x12 @ 75 mph. Ambient temp is 95*. Excursion currently has 240k miles on the clock.
This sound was first heard by my wife two weeks ago. I thought I had tire issues and they needed to be rotated. The sound is still present, and now identified only when the truck is in drive, and under load, regardless of me pulling a trailer.
Yesterday on my 500 mile trip, the truck hiccuped several times which I believe was around the time I was either moving in or out of overdrive. Details in a different thread: [URL] .....
Anyway, I've looked at all culprits and can't find anything with the motor, or electrical system. I can't get to a transmission shop until Monday, and won't have my AE until I get home Sunday night. I have a 500 mile run tomorrow. I checked the transmission fluid and it's at a good level, pink, and doesn't have a bad smell.
I have an 03 F250 7.3litre. I have noticed the last few times driving while hauling that my vents start pushing hot air when under a load (example: driving up a long, steep pull) even if I have the AC on. It's starting make me a lot hot under the collar (pun intended) .....
View 14 Replies