Ford 6.7L Power Stroke Diesel :: Will Airbags Make The Truck Less Bouncy Under Load?
Mar 1, 2016
2015 F350 CC LB FX4. I routinely haul 2-4k of cargo in the back of my truck for 375 mile jaunts.... I do this at least once a week. Most I've ever hauled in the bed was 5k and it rode better than it does with 2k in the bed.
The ride is awful and the bounciness and instability driving on uneven roads or corning at speed is starting to really annoy me. Would a set of good airbags cure this problem? Hit a pot hole while corning on the highway around 60-70mph and you better hang on... feels like the back end is going to jump off the ground.
On my last trip down it was so bad I actually pulled off the side of the highway to see if one of my rear springs was broken. And yes... the cargo is evenly distributed under my truck ARE canopy. E rated tires set at 80 PSI rear, 65 PSI front.
View 12 Replies
Advertisement
So pulling my trailer and 4x4 and the truck dies without any other symptoms. No check engine light all other electrical remains working. This happened 6 times this trip always while pulling a grade but only after the truck has been running for a few hours. Each time, no warning and once the truck has set for 5 to 10 minutes it start up like normal. The longer i let it set the longer I can run before it does it again. ICP is 550ish at idle, 200ish while cranking. Check the FICM before the trip and it was at 47.5 to 48.5v key on engine off and running. STC, stand pipes, dummy plugs, ball cups have all been done.
View 10 Replies
Truck has not been bullet proofed and has aftermarket air intake. Truck has 185km on it (purchased at 160km a year ago). For the Ham Radio guys out there, this is the most electrically noisy vehicle I've owned with S9+ noise while accelerating and S7 going down the highway ...
The faults show up as:edit Can be hard to start cold, takes couple of tries if it's been sitting for a bit (week or more)
No power when cold, that is a lot of pedal results in little power
Misses a lot when cold
Light blue smoke when missing when cold
When fully warmed up which takes 15 minutes of idling regardless the time of year:under load (heavy acceleration while loaded or not, or just in towing, or carrying) it misses a few times a minute, otherwise runs well
It feels like it just doesn't fire a cylinder if it were a gasser, or as if the spark plug weren't connected, but it's not a constant miss, it is intermittent. No load means hardly any misses. Load means lots of misses even running down the road. Should be pulling hard up a hill where it misses lots more.
What I've looked at :
FICM voltage 47.8 standing, 47.6 cranking and running.
FICM is aftermarket and there are no cold solder joints.
Added Archoil 9100 with no change
Wires to FICM are tight and connectors aren't cracked
edit Wires to Injectors are tight and connectors aren't cracked
Exhaust temps range between 500F and 800F during any of these events
Basic ODB reader shows no codes
I'm looking for a couple of things - I'm not much of a mechanic so this has to go to a shop for diagnosis and repairs. Before I run it someplace, what sort of diagnostic tools should that shop be equipped with to find out what's going on? Also, given what you know of the problem, am I likely to damage things if I continue towing activities?
View 14 Replies
I have a 2006 F250 6.0 Amarillo Edition. 133,000 When I bought the truck it was a theft recovery vehicle where the turbo, injectors, FICM and wiring harness were stolen. The company I bought it from replaced the injectors, wiring harness-new, and a used FICM, and turbo. Also has EGR delete and SCT tuner with basic tunes. I believe the SCT was put on to mask another problem. No dealer would spend that kind of money to sell a truck unless something was wrong. The truck would accelerate some with the tuner but shift the tires so hard it would bark them. I removed the tuner and went back to stock program.
The truck will barely move and takes a long time to accelerate under a load. In park and neutral it is fine. A friend has a ford diagnostic program on his computer and says the readings were all good except EBP was a little high. Removed exhaust and air intake to verify no restrictions. Turbo sounded like the vanes might be sticking so I replaced the turbo and VGT solenoid. Now truck feels like its trying to make more boost but not transferring power to the engine. Have blown the silicone hose off twice now during testing. Checked the EBP sensor and tube and only thing I see is a little carbon buildup inside the sensor. What else to check. I'm new when it comes to diesels.
View 6 Replies
I have a 2016 F350 Powerstroke fully deleted for about 3k miles. Truck was running perfectly then out of no where started running like crap and had very minimal power 500-2000rpm. Once 2000rpm hit, turbo spooled up and made power. Very odd. I cleaned out back pressure sensor, map sensor and hoses. No fix. Did a hard reset and the truck ran fine again and had low end power.
Ever since then I started hearing very odd fluttering sounds coming from what I think is the turbo. Also noticed my OEM boost gauge doesn't work. No reading from it.
The flutter only comes on when the truck goes under load for a short period of time and then I let off the throttle. It seems to running fine other then that and maybe a little bit more sluggish then normal. Any things I can check before I put it back to stock and bring it to the dealer?
MODS:
NO Limit EGR Delete
Flo-Pro 5" Straight
S&B Intake
SCT Livewire w/ custom tunes
Also, I had a lot of problems with my live wire software. I have to send it back to SCT to get warranty problems fixed which I'll be sending out Monday. They think my tuner is stuck in demo mode for some off reason.
View 11 Replies
My Airlift wireless will not inflate my airbags-compressor does not run. It was working - only used it once since it was installed 2 months ago. Tried it this week- no joy. I get the error BL OC,(bloc) then sometimes FA IL. I called Airlift Friday and the tech said it sound like compressor might be bad so I should get 12 volts to the compressor and see if it runs. I did that and compressor runs fine. I also checked to be sure I have 12 volts going into the wire loom and I do.
When I try to inflate the using wireless controller, the manifold clicks but there is no voltage going to the compressor. Sounds like there is a breakdown within or between the receiver and/or manifold. I do see the wireless controller sending a signal but nothing happens except on click in the manifold. I guess I will have to wait until Monday to call again. It frustrating since it's Saturday when I am able to work on it but can't get tech support.
View 14 Replies
I bought a 99 f350 truck. it has a van turbo and exhaust back pressure delete. The truck wont make more than 3 PSI of boost. Ive got a p1690 wastegate actuator circuit code. unplugging the waste actuator does nothing. With the van turbo, is the actuator required? Is this code stopping the ecu from fueling and creating boost? I did a cylinder balance test, and cylinder 8 failed. Is a single injector not quite balanced enough to make it not boost past 3 psi? The turbo appears brand new (previous owner said it was), charge pipes hold pressure (tested), EBP Sensor tube is clean (shows up to 24 psi). I tested the wastegate actuator, OnDemand5 says if its over 50 ohms, its bad and replace it. its 69.5 ohms. Again, i dont want to replace it if i dont have to, as its not being used (no wastegate on van turbo), but if the ecu is preventing it from spooling because of the solenoid, ill change it.
View 14 Replies
So I have just over 14k on my 2015....... I love the truck but have had a few small issues. I had a water leak coming in from the roof that would leak through the grab handle. Nothing major dealer replaced one clearance light seal and they said the windshield needs to be re sealed.
Then I had a god awful irritating squeak in the dash..... It only does it late In the day when it's been hot. The dealer said it was a loose air bag. I have had the truck back a week and it's doing it again.
Those are little issues that will get resolved...... I hate having problems with a brand new vehicle but I understand it happens and that's what warranty is for.
I also reported a bad shake to the dealer...... The truck will shake very violently and have a very loud "diesel" sound. It's very specific at when it occurs. It has only done 4 times in the past 6 weeks including today. The odd thing is the 4 times it has done it has been the same time of day in the exact same spot on the exact same road!!!!
Basically I leave my office sit in some traffic and by the time I get to the parkway it has been35 minutes or so. Only happens in 6th at 60 which is roughly 1,400rpm a slight load due to a small incline and it shakes real bad! The typical "diesel" sound you get when under a load is very pronounced almost to a knock. It will continue to do this as you slowly increase throttle until it down shifts and then goes away. I also caught it doing it and I manually shifted to 5th and it went away.
Because of the rpm at which it happens with slight load only doing it in 6th I lean to a Trans issue and more so a converter problem. It feels like converter shutter. I just don't understand the engine sound.
I gave very descriptive info to the dealer..... Several techs drove it and could not duplicate. I just picked the truck back up last Thursday and the dash squeak is back and the shake happened yesterday and again today. So I am a bit irritated to say the least.
I really hate the fact that I know there is a problem but I also understand if a tech can't duplicate it he can't diagnose it. However today I did get a video of it with my phone so they will know I'm not making this crap up!
View 8 Replies
Replaced turbo stock with a wicked wheel. Truck smokes like crazy took turbo out rebuilt it and reinstalled in truck now truck pukes white smoke and has a of white smoke while idling. I don't get why. I've rebuilt injectors about two months ago. Truck is stock not bullet proofed at all. Truck has 170k head gaskets were done at 130k.
View 6 Replies
I have a 2006 F350 Superduty hd 4x4 6.0 Diesel. When it begins to start pulling from a standstill, it will not build power to untrack the load. Once it gets going the turbo will build boost and pull fine. Checked Boots on tube from turbo to intercooler for possible leaks. Replaced tube from intercooler to intake. Made sure map sensor tube was clear of soot (none at all in there). Air Cleaner is in good shape. Im a little Frustrated.
View 7 Replies
I've had my F350 SD for 6months now(21,000 mi) and have seen probably 20 times when I insert the key and turn the switch on the windshield wiper's will make one swipe when NOT turned on. Also have seen several times when starting the truck the radio comes on and it was not on when I turned the truck off. Yesterday when I finished work and was heading home I started the truck and the wipers came up about 1/3 of the way and stopped. I can't seem to duplicate the problem so I have not scheduled it in as of yet.
View 14 Replies
I posted earlier about a whistle that appeared when I was towing my old travel trailer (6000 pounds). It only happened a couple of times, and I had a hard time replicating it, so I elected not to waste any money with the deductable, and possible additional costs for a non-covered issue at the stealership.
Now, I am towing a larger 5th wheel trailer (11000 pounds), and am experiencing this whistle on every steep grade, while towing. Below are a couple of things I noticed, that had to be, before I would get the whistle:
* It only seems to happen while the cooling fan is engaged, and also only when the rpms reached 2800 and above.
*If the fan was on, but the rpms were turning below 2800 rpms, then it would not whistle. It would, however, after the transmission downshifts, bringing the rpms back up, while climbing.
*If the engine was spinning at 2800 rpms, and the engine fan was not engaged, then it would not whistle, until the fan would kick in.
* It only seems to occur when I am climbing a steep grade, on a warm day. Although, I haven't experimented on steep grades on a cold day...
It sounds to me like there is an issue with the engine fan system, but I thought I would put it out there, just in case any of the diesel guru's out there might know of something else that would cause a whistle like this, i.e., turbo?
Oh by the way, I also think that I have a performance reduction lately. However, I can't know for sure, as I have never towed this much weight with my truck before. I just kind of expected that I would be able to pull to the top of these grades, with a little extra peddle to spare. I have to floor it, just to "try" and keep up with traffic. And I haven't calculated my fuel mileage while towing this beast yet, but WOW, that fuel gauge needle sure does drop like a rock!
View 14 Replies
My 6.0 stalls out when under load above idle intermittently. When it stalls, if I release the gas pedal and tap it, it usually catches again but not always. ICP is strong and doesn't seem to waiver when it stalls. Engine runs much better when oil comes up to about 180. Oil / water temp spread about 5 degrees.
View 14 Replies
After replacing both heads with remanufactured heads from ford along with new egr and oil cooler a month ago, she still overheats when pulling a load. While normal driving and not towing, no problems. In the last 5,000 miles since work was done and while towing approx. 15,000 lbs (load and trailer weight) she got hot once, slowed down, temp retreated got home - she has not overheated since then pulling 4-5 loads over the next 2,500 miles. Today at about 75 degrees only 4 blocks after picking up a load at about 12,000 lbs she started getting hot again. After I let her cool down and got on the Freeway the temp went down, appears she's not staying cool in the city with a load on. With all the work and new parts I had installed, what the problem might be?
View 12 Replies
Like the title says, I want to raise the front of my 07 F350 about 2.5 inches to get it closer to level with the rear with out throwing the alignment out of wack if that's possible. Maybe some blocks to go on the front coils? or will I need new front coils that are a bit longer?
'm talking about the FRONT of my F350.
View 14 Replies
I ran about 500 miles today loaded up pretty good and noticed every bump I hit that was enough to rock the truck and trailer that there was a noise I've never heard before. It was like the difference between asphalt and concrete road surfaces, but was only present when the springs were sufficiently compressed. Temps were between -10 when I left to 10 or so above when I was destinated. Would that cause the noise?
View 3 Replies
I have a 2003 f 350 6.0, when under a heavy laod such as towing a 3000-pound trailer up a long hill at approx 60mph and 2000 rpm it intermittently mis fires.The boost gauge bounces up and down and i here a poping sound from the engine compartment.I have had it to several dealer and independent shops but with out the trailer or a heavy load it runs perfectly.They have told me fuel pressure is good and changed all fuel filters with OEM parts.
View 3 Replies
2005 F250, 6.0, 60K miles, recently (within last 1K miles) had ARP studs, EGR delete and new oil cooler installed. Shortly after (5-6 weeks later) I noticed blue smoke under any load (taking off from red light, backing up) but not at idle or startup. Was using the "Performance" SCT canned tune after the stud install, but had the "65HP Tow" canned tune installed when I first noticed the smoke and now back to stock after noticed the smoke as a precaution. Everything else original except FICM, filters and batteries and use 5w40 Mobil 1 since new.
View 14 Replies
While i am pulling a loaded trailer we have been experiencing a random Chug that only last about 1 second we have no lose of power during when it happens. We Recently just replaced all fuel Filters. We have an updated EGR on it with a cold air intake and muffler delete. It has about 180000 miles on it it runs awesome and starts right up just trying to figure what this problem could be..
View 11 Replies
In the last 3 weeks I've replaced the oil cooler. IPR, ICP, fan clutch, intercooler, rebuilt the turbo, new elc coolant, egr valve, thermostat, new batteries, positive battery cable, and alternator and a host of other crap. Now I have a new problem.
When towing it overheats, almost instantly under load. I was towing a 9k trailer up a hill, a total of about a 30 second climb and it overheated (242 degrees). I'm thinking head gaskets at this point as they are stock and have the tty bolts installed.
View 14 Replies
Recently had a rear pinion leak and replaced the seal and nut. I jacked up the truck, took off wheels and felt the drag so I could duplicate once i had the new seal as I tightened the nut. I've done this only once before on my F150 years ago, but when I put the driveshaft back on and test drove it, i had shudder when not under load. So when I let off of the accelerator, it had shudder and more the faster I was going.
Obviously thinking this is a preload issue with the rear axle but would this be caused by tightening too much or too little. I had no issues before so I would think that the driveshaft itself is not the issue. I can't confirm that I got it bolted up in the exact same manner as before in relation to the flanges but still wouldn't think that to be the issue.
View 6 Replies
