Ford 6.7L Power Stroke Diesel :: Whining Noise On Cold Start When Turbo Hits Certain RPM
Sep 27, 2010
My truck's been doing this ever since I got it when the engine is cold. Haven't brought it up to a dealer yet because I'm not sure it's a real problem, and since it only does it when it's cold I'd have to leave it overnight.
It seems to happen when the turbo hits a certain RPM. I got it on video but you can't really hear it until the end when I raise the RPMs a bit.
YouTube - VID 20100926 104950
View 14 Replies
Advertisement
When I start the cold engine mine makes a loud whining noise. I took it to the Ford dealer and they said that the sound is normal and that it's the turbo's. I think I'll take it to another ford dealership and get a second opinion, The service guy has the same truck as me and his was making the same noise on cold start up and they told him it was the turbo's also. Something's not right about the noise.
View 14 Replies
I have a 2011 F250 that I bought new. It's been the best truck I have ever owned. It now has about 105K miles (170k Kms). Lately the turbo has started whining at low speeds and idling. Is this something I should be concerned about. I talked to a diesel mechanic (not Ford) and he said this is fairly common in some vehicles.
View 6 Replies
I've been getting some grayish/blueish smoke on cold starts lately and decided to do some investigation to see if there was a problem or just the cold temps.
I googled it and turbo oil seal problem was pretty common so I figured it was easiest to start there. I removed the pipe between turbo and CAC and it had quite a bit of oil it in. The pipe after the CAC had a fair amount as well. I checked the oil level in the engine and it was slightly down but I can't say how accurate the dipstick is nor it was completely full after the last oil change. Either way, not much oil is entering the intake but I would assume any is too much.
Here's my main concern - What's the likelihood of getting a runaway from this?? Is it possible for the oil seal to fail 'more' than it already has putting more oil in the intake allowing for a runaway condition?
Obviously the turbo needs replaced but is it safe to run it the way it is until it completely fails or replace immediately?
View 14 Replies
I have a 2011 that does not currently have the complete factory exhaust system on it and no muffler. With the nice weather I have been driving around with the windows down and hear a noise out of the exhaust that sounds like tires spinning on wet pavement when I let off the throttle or at some shifts of the transmission. Boost seems normal, and don't hear any noise while under load. I think it is just the VGT closing and making the noise. With deleted sys heard this noise in exhaust?
View 4 Replies
I just picked up a 2006 F250 6.0. It was having hard starts. Anyways before I started using it I started tearing things apart cause I knew for sure the turbo was leaking so that had to be resealed. I just picked up a 2003 turbo today for it out of a used truck that had 144000 kms on it. (was in an accident). I am gonna post up a few pics here of the engine bay area, there is a huge amount of old oil I believe to be, I am wondering if it was a leak or spilled oil. I am going to be cleaning this up. Putting 03 turbo in here, doing a service and then plug my Tablet with torque pro and post up some numbers and see how healthy she is. Before I post any pics Is there a way to make these pictures clickable instead of them taking room up on the page?
View 14 Replies
I have an 04 F350 and I was wondering if the fan is supposed to be locked up when the A/C is on. In max A/C with the fan on 3 it's barely keeping cool in the 95 degree heat we have been having. If I rev the engine I don't hear the fan noise like I do when the coolant temp hits 218 and the fan roars. Freon was replaced several months ago, along with receiver/dryer and orifice tube when I did the HG's. The A/C shop drew a vacume and did not find any leaks.
View 7 Replies
In addition to significantly louder noise from the Turbo on start-up, we've started to hear a pretty concerning noise while descending a hill in Tow-Haul. Not sure that the T/H has anything to do with it other than getting the engine in a RPM range that causes the noise. We've taken it in and tech says "That's just normal noise"... What ever that is.
Here is a link to an example : Tow haul making a lot of noise in my F350 diesel. Pulling a very heavy horse trailer. - YouTube
Best next steps for a 64,000 mile 2012?
View 8 Replies
I have a 2013 F350. Since it was new in August the turbo has made a chattering sound that sounds to me like the waste gate (if it had one) is opening and closing rapidly. Almost like its building boost and dumping it over and over again. Usually happens when it is in 6th gear around 1700 rpm under light load. It also does it from time to time while plowing snow. You can power through it or let off and it will go away. My local dealer where it was bought new put a new turbo on it and the problem still persists. The truck just turned over 8k miles and has been in several times in attempt to resolve the issue. They say that there are no codes on the truck nor does Ford have anything on their service web. My dealer claims that no one has ever had the issue.
View 14 Replies
My first opportunity to really use four wheel drive and I am having a whine and a very slight vibration from the drivers side wheel. The noise is only noticeable under throttle/load. When I let off, there is no noise. The truck is also quite in two wheel drive.... No whine.
The truck has been to the dealer for a front end clunk that is coming from the drivers side. The dealer, as usual couldn't replicate it, and didn't do anything. I notice the clunk more on the rebound. I also notice it when using more of the suspension travel i.e. going over a apron into a shopping center, or the crown of a cross street when traveling at a good speed. Short choppy pothole bumps don't replicate the noise as easily.
If I had to guess... The two issues are related. Narrowing it down will be the key. Transfer case? Failing hub? If I don't spoon feed the dealer, I will never get it fixed.
View 10 Replies
I have an 03 super duty with the 6.0, came back from vacation with my 5th wheel in tow. Lost the upper turbo hose twice on way home. Managed to get it rigged and made it home and parked it. a week later went to uncouple and move the truck and had some very strange issues. Started fine but could barely make it up driveway (no trailer at this point). No power, felt like when turbo hose came off. Got it moved and checked turbo hose and all was good?? Went out a couple days later and no start.
Checked all relative fuses and relays and all checked good. Jumped starter solenoid and starter worked fine. turned key on and jumped quick connect on right side of engine compartment to battery and it fired right up and ran. Jiggled shifter around in park and neutral and nothing. BTW I always here the relay clicking and swapped with one of the others just to be sure, same thing. After looking on the internet for a day and a half thought maybe a NSS in the tranny but I think I have the 5R110 that does not apply??
View 4 Replies
I have a 2005 F250 with 186K miles. I do minor work on my vehicles but have little experience working on my diesel. I was accelerating when I heard a pop and a hiss similar to disconnecting an air hose from an air compressor. Total loss of turbo power. No turbo reading on the turbo gauge on dash. No loss of oil. No smoke. Oil and coolant look fine. Took off turbo and everything appeared to operate like it should (according to YouTube videos). Inspected lines and rubber boots.
Rubber has some cracks but not certain if they are holes. How small/large of a hole would cause total loss? Was originally scared to take it to a shop knowing they could name their price. Not opposed to taking it somewhere now knowing the turbo works but obviously would rather save the money. Any tips on troubleshooting? I'm not opposed to proactively replacing parts/sensors as the truck has given me 186k and I plan to keep it as long as possible.
View 8 Replies
Just pu my new 2013 6.7 Diesel with 1300 miles... There is a most annoying whining coming from under the hood and sound like its coming from the secondary filter area or turbo (you can even feel it if you put your hand on the filter lines and housing) and it starts a minute or so after the vehicle has been running and you can her in the cab at 70-mph... At drive through restaurants I have to shut the tk down to place my order and never goes away..
[URL] .....
View 14 Replies
I have 2003 f250 6.0, had the turbo rebuilt and I put it back in, my turbo is whistling but I'm also getting a humming noise kinda sounds like a when u down shift at high rpm's idk what's going on, I try and power break as well to build up boost and the tires do not even spin...
View 4 Replies
For a while now, I have been hearing a very high pitch whistle noise from the turbo/exhaust area. Everybody told me it was an exhaust leak, but I never could pin point the leak. While I was under the truck last weekend I found the flex joint on the passenger side up pipe was broken a leaking.
I ordered a Dorman replacement pipe that comes with a new gasket and hardware.
I will be the first to admit, I am not a fan of Dorman parts... BUT, this pipe is really nice. It looks identical to the pipe being sold on Dieselsite.com, it doesn't have the scoop inside to direct exhaust gas to the EGR cooler and it comes with all the mounting hardware.
[URL] ....
Once I got the turbo down pipe out of the way and soaked the bolts with penetrating oil, I had the broken up pipe off in 30 minutes.
View 8 Replies
I've got a stock '15 F250 6.7 w/ the Diesel Site FF67 fuel/water separator and a 50gal Titan Tank. I installed the filter + tank at the same time around 2 months ago; A few weeks ago, I started noticing an odd buzzing/whirring/gurgling noise (both while the truck was running, and while the fuel pump spins up right after turning the key on). I made a quick video of it this morning:
Ford F250 6.7 w/ Diesel site filter DFCM buzzing/whining - YouTube
I thought maybe it was a filter related problem (I got some little black plastic bits in the filter after installing the Titan Tank, despite my best efforts to clean it out thoroughly before installing) - so earlier this week, I replaced both stock fuel filters, and both filters in the DS filter. Didn't seem to affect the noise from the DFCM at all.
I guess my question is - does it sound like this is sucking in air? I've never found any leaking fuel (even after a 3000mi drive from TX to VA and back), and the truck has never complained about low fuel pressure as I've read that some others have run into. But I don't remember the DFCM/low pressure pump being this loud before I installed the new parts.
I spoke to the folks at DieselSite a day or two ago (those guys are great), and they mentioned that sometimes the Ford quick-release fittings work themselves a little loose from the fuel hose during the filter install, and that putting a hose-clamp around the hose+quick release fitting may solve this; I ordered from clamps from McMaster Carr that arrived today, so I may give that a try tomorrow just to see if it changes anything.
View 14 Replies
Well.. my truck has been running great for the past few years. This morning I went to start it and all it does is cranks and cranks.. no start not even a sputter.. I use the torque app and noticed the HPOP was over 900 psi during cranking and ICP volts were .8 volts. FICM was 48.5 and around 47 during cranking. I even unplugged the ICP connector and got the same results.. just cranks and no start. i noticed while it cranks i don't get any white "smoke" coming out of the tail pipe I even sniffed in there and I don't smell any diesel at all.
I pulled the upper fuel filter and it is full of fuel, the fuel pump does its normal buzzing when the key is turned on. I even checked the emergency shut off switch for the fuel pump and it was fine. At the moment I am charging both batteries... they were draining because of all the cranking. I think I will check the FICM with a multi meter when the batteries are good and charged.. Seems weird to be running fine with no hints of issues then all of a sudden its dead.
View 14 Replies
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 Replies
I just bought a new to me, 2005 ford f-350 6.0L turbo diesel with 220,000 miles. It has an EGR delete, and aftermarket intake and exhaust. I am having power loss issues, and cold start issues, and judging from these symptoms, I figured it was the FICM. I thought it had to be the FICM. As per the tech folder on this site, I tested the FICM. I first learned that I have one of the Bullet proof FICM's, and when I tested it (3 times) it read between 57.5 and 58V. I conducted this test three times both with just turning the key, and with the truck running. I then took the truck into Ford, and they gave me a list of all of the codes the truck threw:
P0611
p0113
p0405
p0671
p0673
p0675
p0677
p0341
I researched all of these codes, and it seems to point to the FICM, but Ford stated they pulled a reading of 54.5v. The tech then told me that the upgraded bullet proof FICM probably ruined my injectors, because my injectors we not upgraded. Is this True?
Even though my FICM is above the low limit for voltage, can it still be going out? I am taking the truck in to have the batteries load tested, so I will know if they are contributing to my FICM failing.
View 13 Replies
So I have an '03 6.0 with 151000 and change. I go out to light her off in the morning and she fires quick and easy. Idles well and no complaints. But when hot shes sluggish to start. Now it's not what I would call a typical hard start considering I've watched videos on YouTube and guys are having a lot harder of a time then me getting theirs started. It's just not the same as cold it almost sounds like it's lacking fuel cause it starts real low after fire then with a couple revolutions it perks up. And this is without the key still in it. Again no idle or running issues at all. I've been trying to see if it could be my ipr? My ficm is new and never gets below 47V but idk what it is.
View 14 Replies
Been having an issue every once in a while for the past 3-4 weeks.
Truck will not start when cranking sometimes (has happened 4 different times as of today), then I will stop cranking, and retry and it will fire up.
Of course when I try to replicate the no start, it won't replicate. So from here on out I will make sure my Torque Pro connects to the BAXF before cranking.
I know to look at the HPOP psi number.
I need to know the other parameters to look at during cranking. I am suspecting the STC, dummy plugs, or stand pipes with a leak by or drain down of oil.
View 7 Replies
