I changed out my fuel filters today on my 2016 F350 SD and right parts, no leakes, main filter full, and I did the 6 cycle fuel pump prime. Turns over but won't Start. Redid the 6 cycle prime several times now and still no start. Pulled the 2ndary filter lines while it was priming to see if flowing and got squirted on both lines.
View 8 RepliesI've done some searching on this site and found some good information but I still have some questions about Fuel Pressure and fuel flow. A few months back when I had a bad injector and bubble tested to verify and it took around 15 seconds to fill the bowl(filter removed) from near empty is that normal or the sign of a healthy HFCM?
Tonight I was able to check the fuel pressure for the first time and when I turned the key on fuel pressure was slow to build for 2-3 seconds held at 20 psi then spiked up to 62psi and stayed at that psi during the starting cycle and held steady during idle. Is it acceptable to hesitate with a pressure build at the beginning of the cycle?
I'm new to the Ford 6.0 diesel motor just got one from someone and the fusses and relays have been messed with. I have fuel up to the second fuel pump and it sounds like it's working but It just turns over. I purchased the Haynes manual but it doesn't have information on how to test the injectors or fuss box set up.
View 8 RepliesSo loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 RepliesTurns over great but nothing. just changed fuel filters all voltages read great. I have ScanGuage and what little I can tell everything reads good. Has been acting funny for a couple weeks taking 4 or 5 cranking attempts to start every now and then no real pattern. Runs great when going even when pulling a load. It has failed to start and I'm in my shop and not sitting on the side of the road.
View 6 RepliesI have a problem with my F250. The engine is turning, rail pressure 400kpa, but it does not jump at. Injectors are tested at bosch. High and Low Fuel Pressure Pump are new.Sensors and pressure regulator also. Compression is also ok on all cylinders.
View 4 RepliesI "Bulletproofed" my f-250 Super-duty last summer and she ran great for a time, actually she is still running great, except for one thing that is driving me crazy. On a cold start it turns over until the oil pressure builds up. Then she will crank and runs fine, also starts normally after warm, turns over a couple of times and cranks.
I have oil in the filter housing, have replaced the seal at the bottom of it. Just pulled the oil rails off and replaced the seals on them, and a new IPR seal and filter. I am still having the problem, F.I.C.M. voltage has been fluctuating between 45 and 46 vdc. I have a P300 and P308 code.
I haven't really considered Injectors because it is idling smooth as silk and has great power.
My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.
P02E1 - Diesel Intake Air Flow Control Performance
The air box gauge is green and it doesn't reset when I push it so that appears to be fine.
The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.
Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.
I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.
I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.
This is a new truck to me 03 Excursion, the owner has done a lot, gave me receipts for a lot of work and cosmetically it just seems taken care of. About a year ago hpop, ficm, oem egr and 3 injectors. He wasn't happy with that mechanic and still having problems so went to a different (supposedly better) shop. This time turbo cleaned, all 8 injectors and passenger head was redone and put back on with oem bolts. Apparently it was found that a nut was dropped down valve cover by the first shop! Somewhere along the way the ICP and GP module has been replaced.
I've only driven it a couple times and seems great until last night. It was loosing power and in about 10 seconds died and wouldn't start back up. Pops but doesn't stay running. WIF dash light on and no CEL codes. Not sure where to start/what to do. I've paid for most of it and was planning to pay the rest and transfer title but I'm not comfortable doing that till I'm confident it's good to go.
I drained the separator and seemed to gush out like it should and don't think I saw water. I'm planning to take the sensor off the filter there, inspect and clean it but I don't imagine that's the problem. I do see oil coming on the back of the engine and front of tranny on the drivers side... maybe ICP is all oily and failed? I don't know much about these, just been trying to read. What should I do as some first steps? Do I need some sort of scanner? It seems like it's starving for fuel. It was about 1/4 of fuel when I bought it and filled it up the night I took it home and have put about 80 miles on it since. Is it possible it's got bad fuel or water?
2004 f450 with 6.0. Was driving down the road when it started losing power like it was starving for fuel. It carried on for about a mile then died and will not start. No codes at all and we put a new fuel pump on but still wont start. Put a rag with gas in the air box and will run but rough.
View 6 RepliesIs the irp high flow oil cooler any good? Or is it better to stay with the oem
View 14 RepliesJust as the title says the ac on my truck is not blowing cold like it used to, it has enough air flow but it's just not cold?
View 5 RepliesNew to me 05 6L. I bought it out of town and they delivered it today, I picked it up and noticed the fuel gauge was way past empty, no fuel warning light or anything on.
So I mistakenly decided the fuel gauge wasn't working right (they just drove it 200 miles) as theres no way the seller would cut it that close on fuel.
I drove it to insurance place did another errand before I got fuel. Shut it off and it wouldn't start again. Tried it a couple times before it clicked it was out of fuel.
Borrowed a truck and went for fuel. Still no start , took the top off fuel filter , nothing in it. Recycled key 10 times still no fuel?
Replaced both fuel filters same as usual. Cranked right up and I let her run while I put up the tools and look for leaks. Notice it started running rough, so I jumped in and started to back out of carport and it went dead. Ran battery down and it won't hit a lick. Replacement (racor) filter same as last few changes. Running just fine before change so it has to be something simple, but what?
2006 6.0 powerstroke
ICP and IRP changed both fuel filtrs and Blue spring put in. HPOP Pressure is over 1600PSI when cranking with 2.5 to 4 volts.
Will try to run but acts like not getting enough fuel. If I loosen the lines off the upper filter housing lots of fuel runs out. Lots of smoke when cranking also.
FICM volts are 48.5.
Reading with Scan Gauge 2.
The truck is a 2003 F350 DRW Stock 6.0 with 433000 on the odometer.
I am driving a early 2004 F250 CCSB with a 6.0l. I have a Code that is for an EGR Low Flow. I have a Scan Gauge II that I have been using to try and determine why this is. I have replace the EGR Cooler (unrelated), the EGR valve, and the MAF.
My EVD and EVM are tracking. My IA1 reads a letter (B usually) and 3 numbers that are in the 6 to 900 range. My IA2 appears to read normal with atmospheric temps at start up and goes up and down IAW the EVD and EVM readings. My FIA (already programmed) reads outside temperature along with the overhead console. The EBP reading doesn't exist, it is blank.
Coolant flow seems to be not at its max output seems like it's blocked somewhere. Lots of pressure in bypass line of radiator after clamping of hose and releasing pressure of degas bottle?
View 11 Replies2003 6.0 no start. turn the key to on and nothing happens. dash lights up as it should but I don't hear the glow plugs cycle and no fuel gets into the upper fuel bowl. turn the key over and nothing happens. No starter click nothing. tried the starter wire to the battery trick and it cranks but does not kick over. checked ficm wires and they are secure as well as the injector wire on the intake manifold. it is the original ficm.
View 6 RepliesI am new to the FTE world but not to diesels my 2012 f350 is my second diesel and a couple weeks ago I got home from work and fell asleep and forgot to plug in my pickup and it gelled up (was about 15degrees when I fell asleep and -20 when I woke up) so all the filters were replaced and everything was good after that for about a week, then my fass platinum pump started blowing the 30a fuse every 10 seconds and The pump itself smelled burnt so I replaced it with the same style and size of pump and the pump is good now but the truck is a no start it has thrown codes p2291, p0089, p0091, and p228e. It has 4inch straight exhaust, fully deleted (def and egr), h&s tuned, fass platinum 125 lift pump.
View 14 RepliesWent and changed my fuel filters today... Primed the truck 6 times. Started it. Ran great, then got a low fuel pressure and reduced power notification. Turned it off. tried priming it 10 more times, no start, tried 15 more times. No start. Took off the outlet on the secondary filter, solid flow. Took off the return on the L/H fuel rail, pinched the line and put a hose on the rail... Once again solid flow. I can hear air somewhere under the hood but I don't know where... Driving the 7.3 to work tomorrow but this is driving me up the wall.
View 14 Replies2005 Starts fine after first start. Ficm voltage 47 to 48 on Edge insight, stc replaced...
View 14 Replies