Ford 6.7L Power Stroke Diesel :: Turn Signal / Wiper Switch Failure
Jul 17, 2015
Started truck, used windshield washer and noticed High Beam Indicator was lit on dash. Headlight switch not on. Drove to Ford dealer, turned off truck, high beams would not shut off. Dealer replaced the Turn Signal/wiper/High beam switch assembly. Dealer had one in stock. Service manager said they have replaced a few of these Switches. So if your High Beams come on without the headlight switch on you cannot turn them off even if you shut off and exit truck. Also the "You left your lights on warning chime" does not sound when you exit truck.
View 14 Replies
Advertisement
Looking for a tutorial on how to remove the multi-function switch? I have the, seemingly, common issue of wipers not turning off. I bought the new switch, but don't see how to get it out without taking the whole steering wheel off. I can't get to the screws on it at all. I got the plastic covers off, but can't see how to get the switch out.
View 3 Replies
I have no wipers or windshield washer. when I turn on the wipers I can hear a click in the cowl at the wiper motor. fuses are good #106 30amp fuse and #33 15 amp fuse. I have 12volts at the wiring on the motor left side with key on and 4.5 volts on the green wire with key off. I replaced the wiper motor and same thing, just clicks when I try wipers. I connected a jumper wire to the ground and no luck.
View 11 Replies
The other day i noticed my turn signal was blinking rapidly. I found that my drivers side bulb was burned out. I am trying to convert most of my lights to LEDs on my truck and figured that I'd replaced the tail lights with LEDs. After replacing both rear taillights with LEDS I still have the rapid blinking turn signal. Whats the deal? is it just the LEDS or what?
View 13 Replies
Last night I was heading home from a two day race and found that my turn signals wasn't working. the running lights are working and obviously i could feel the brakes working.
well i hooked up some jumpers to a 12v battery and the 7 pin and the lights work. to make 100% sure it works i hooked it up to my neighbors Tacoma. it all worked. well..........
On my last f150 when it was new this happened to me too. it ended up being the turn signal fuse on my truck.
I hooked right back to my truck again and just made sure my plug was all the way in and still nothing so i know its my truck side.
Now my last f150 owners manual had a section to where it told you what fuse is what and where. well i don't even see the f250 fuse box is and don't know which one it is to see if its blown.
View 7 Replies
All of a sudden, my turn signal won't stop automatically after making a turn. I read that the multi function lever needed to be replaced. I did, and nothing changed... what is wrong since its not the lever assembly itself?
View 6 Replies
Hearing a whistle noise after installing the Recon smoked turn signal lense? The whistle starts between 40 and 50 mph and is the driver side only. I have triple checked the installation and it has the same clearance all the way around as the left side. I sent Recon an email on Jan 5th about this issue and still haven't heard back from them.
View 14 Replies
I'm looking for a 3156 LED Amber turn signal bulb for the front turn signal, I've looked around haven't found anything! Any success story with this particular bulb, and does it require a load manager when installing?
View 14 Replies
2004 F250 6.0L!!
An issue I noticed right off the bat was that whenever I had the driver side turn signal on, and the brake was applied, the turn signal freezes.
I took apart the tail light and found a concoction of wires...I posted a diagram illustrating what it looks like.
There is this pesky Red wire that is spliced into the tail light bulb socket wire (specifically the green wire).
There is a trailer brake installed...if this means anything. I've tried disconnecting that with no luck on fixing the issue.
How to further troubleshoot would be great...electrical work is not my forte!
View 14 Replies
Ok 2011 ford f350 6.7. Turn key on, no crank, no start. Trailer brake module failure flashes on the screen. If you leave the key on after 5 to 10 minutes the heater kicks on and you can start it. Runs down the road, hitting every pot hole for 1000 miles fine. Shut it off, try to immediately restart, same thing. If you hook up a booster box to it it starts. Replaced both batteries, cleaned cables. Scanned it, only codes are with the instrument panel : loss of communication with trailer brake module, with abs, with heat and air, and with parking aid modules. Tried to scan abs, parking aid, and brake, scanner would not communicate. When it is running communicates fine with them. Need a direction to go from here?
View 14 Replies
After disassembling what felt like the whole front end of the truck, I finally gain access to the danged thing. Mine has been acting up intermittently for about year and half I guess. When flipping to switch to signal turning, it started making a buzzing sound. At first it was doing it most of the time. Then it cleared up and started working right for several months, then act up, the act right. Well, now it makes the buzzing noise more often than not so i decided to address it. I went to Oreilly, they didn't have one, but told me the part number.
I went across the street to Autozone, that had one on the shelf that was same part number as Oreilly. I put it in and when flipping the switch, the relay does it tick tock sounds like its working, except for there is no indication on the dash cluster that its working, nor are the actual lights working. I swap back to original and buzzing, put in new one and tick tock but no lights. Whats the deal? Is this one of those things that you have to go back to Ford? Or maybe i got a bum relay from parts house and should exchange for another to see if it works?
View 6 Replies
I just bought a 93 XL and had some parts to replace.
Had to replace the clock spring and wiper/signal assembly to restore the wiper squirter function, cruise, horn and airbag.
Thing about the repair is that now my cruise quits holding the set speed when I lift the turn signal to change lanes from the left to right lane or turning right.
Does not turn the cruise off; it just does the same as hitting the brake. When I hit the resume button, she goes back to the set speed. Replaced it with a new assembly, thinking it was a defective part. Not so.
The replacement part is not OEM.
View 8 Replies
I have a 2012 Ford Focus. The switch for the wipers does not turn on the wipers. However, sometimes the wipers go intermittently when the switch is off - even if ignition is off (and key removed).
View 2 Replies
Looking for a video or directions as to how I replace a windshield wiper motor on a 2006 SD?
View 2 Replies
6.7L ... Just traded in my F250 on a 2011 F350 Lariat. Love it. Period. Except that my windshield wiper sprayers will not work. I don't hear anything when I hit the button. No click or motor running. I can't figure out what fuse it is because I don't have an owners manual.
View 14 Replies
My truck had to be towed to the shop today. The wife and I were stranded for 2 hours and to say I was upset is a understatement. My truck has 13,800 miles and this type of failure is unacceptable. Is it necessary to carry extra sensors around in order to get your truck off the side of the road? BTW, my truck didn't even make it to the side of the road, we had to push it to a narrow shoulder on a busy side road.
View 14 Replies
Had CEL light and took truck to dealer and they replaced Bank 1 sensor 4, two days later, CEL again Bank 1 sensor 3.
I've trouble shot many EGT sensors on Airplanes, and we could tell if there was a failure coming if a couple failed by testing the sensors themselves. My Service Manager told me there is no way they can check the others out. That sounds like Bull to me.
View 1 Replies
Looking for an electrical schematic and or wiring diagram of the windshield wiper circuit for a 06' Super Duty?
View 5 Replies
So I have a 2006 Ford F-250 6.0 that broke down about 2 months ago due to an EGR failure. Took it to the dealership got it fixed along with a new injector everything has been running fine only thing I notice is a big split in EOT and fW(218 EOT and 192 fWT). Well yesterday on the way home my wrench light comes on I tried to scan it with the scan gauge but it said no codes found and when I got home and turned the truck off and back on the light went off. What could cause this?
View 11 Replies
I'm at 76K miles and I had another exhaust sensor go bad. This time the check engine light came on and the truck did not shut down. I was prepared this time and had an extra sensor / code reader handy.
It was the last sensor in line and very easy to get to. It took me less than five minutes to complete the job. I did use anti seize, but as easy as it came out it probably wasn't necessary.
View 14 Replies
I only get random TPS failure messages when I am hauling my cab over camper and towing a horse trailer. Other than Murphy's law which dictates that these type of events only happen at the worst times (fully loaded w/ kids, dogs, horses, steep grades, no shoulder, 110+ temps, etc) I figure that the big metal box is disrupting the TPS signal reception. Not sure where the antenna is for the TPS system. I stop and check pressure/temperature just in case but all is well. My Lance has a sheet metal skin and blocks satellite completely and terrestrial radio somewhat, which I don't use anyway.
View 2 Replies
