Ford 6.7L Power Stroke Diesel :: Turbo Died When Driving Down The Highway At 55 MPH
Mar 8, 2013
Turbo is dead. I knew this day was coming. It died driving down the highway tonight at 55 MPH. Plenty of power since I left the office, all of a sudden the tone of the engine changed to a 6.0L and there was no power at my disposal.
Nursed it home keeping an eye on EGT's and let it soak while I ate supper.
Started it up, let it idle for a minute and tried a few revs but no boost and no turbo whistle.
Garage actually had a very slight haze to it after the test revs so something is broken.
DPF shouldn't be allowing any type of smoke to pass.
Bummer. Now I need a rental so I can get to the airport. Murphy's law has been in effect all day between software upgrades (IT stuff) and now my truck.
No CEL (this is shocking to me) but I found : P132B - Turbocharger/Supercharger Boost Control A Performance
View 14 Replies
Advertisement
2006 f350 6.0..... I was driving for about 10 hours and truck ran fine. Until with no warning it just died. Got it towed home and now I try to start. It turns over fine but no fire.... I know not to use but we used starter fluid to see of it would fire thinking maybe file filter bit still no fire with the starter fluid. I find it weird that it won't fire even on stater fluid. The engine oil was very low as well but since topped it up.
View 14 Replies
Truck died going 50 mph and would not restart. I turn the key to run and nothing. I can hear the injectors buzzing but it will not turn over or crank. I can jump from the battery and the truck will crank. However, it seems to be in limp mode. It will start off in 3rd gear and won't shift gear Tow/haul light is flashing.
The wire harness that goes down to the fan clutch is chewed up and frayed so I'm assuming that may have caused an issue. But i have unplugged the sensor to the fan clutch and it still won't start. I can hear the injectors buzzing but when I turn the key to crank it, it does nothing. Just clicks. I've cleared the codes and these keep coming back.
View 14 Replies
My truck died a few weeks ago on the highway had the hpop ipr valve and screen replace ran awesome for 2 weeks, shut it off ran into the store and it wouldn't start gave it a couple hours finally fired, started good the next 5 times go to start it the other day no start again, tried again 30 seconds later and starts trucks a 2006 with 226000km throwing no codes, I'm ready to go trade it off on a new one, where to start?
View 9 Replies
I've come to the conclusion that after 300,000 miles my turbo is sticking. I need to drive the truck up to my mechanic but he's 50 miles away 90% highway (really don't wanna pay the towing bill) would this hurt the truck any more or would it be okay? If it will hurt the truck more I'll get it towed but I'm trying to avoid that at all costs. I have drove it since the turbo began to stick but it is very sluggish and smokes a lot. As soon as I let off the pedal boost immediately drops to 0 psi.
View 3 Replies
My Brothers truck died while driving and won't restart. I am going to be getting IDS on it tomorrow night and just wanted some feedback on things to watch. I am planning to watch FICM sync, ICP pressure, IPR %, FICM voltage, and fuel pressure(not in IDS). Anything else I should watch while testing?
Edit: this truck is a 2005
View 14 Replies
While driving uphill yesterday, my truck 6.0 f250 completely died. Added oil cause it's been a while and tried starter fluid. Cranks but won't start. Pulled OBD codes p0300, p0304, p0401, p0460, p0562, p0606, and p2290. Checked IPR, works fine. Checked fuses. Low voltage codes are most likely from battery dying during the test.
View 2 Replies
I have a 06 f350 with 140,000mile and today I was driving to a buddy's house and the truck died on me as I was doing 45mph so I towed it home and check the codes I have 1 low icp pressure and 1 low icp during starting / cranking and 1 ckp out of range I think that how it's worded so I looked at the icp pressure and it's 0 and the desired is around 1000 and the volt is .56 and as far as the ckp the rpm are reading so I don't know what to do about that ? Could the STC fitting and dummy plug and standpipe o rings really go out on me like this ? Or am I missing something? I am also trying to track down a oil pressure gauge for the Icp fitting to check it
View 9 Replies
I am working on an 2003 F-250 6.0l. The truck just died while driving. No restart. Plugged in my scan tool and I am not getting any High pressure oil. Is there anything other than the Hpop I should be looking at. I know it is a big job to replace the hpop so I don't want to overlook something simple.
View 14 Replies
I have a 07 6.0 that won't start it died a few weeks ago while driving. Being a mechanic I've done numerous things to the truck in order to fix all the common 6.0 problems but can't figure this one out. It will crank and get oil pressure and fuel pressure but seems to not be getting fuel. The IPR valve isn't clogged I tried with 2 working valves nothing worked. Along with changing the ficm. The connections to the ficm are clean and all in tact. I have an edge evolution chip that isn't even showing any codes. Not sure what to try next since I don't have any codes to go off of.
View 11 Replies
While driving my truck to work this morning, it completely died at 65mph. The radio and all electronics are still working. Coasted to a safe place to try and restart, but it won't turn over. The glow plug light stays on. Could this be an alternator problem or something more serious? I'm waiting for a tow truck. I'll see if there are any codes when I get it home.
View 14 Replies
My wife was driving through the intersection when the truck died... Tried to start it again but no go, I had it towed home, and stared to troubleshoot.
I have a Scan gauge2 and these were the readings: FMP: 47.5, IPR: 84.71, SYC: 1, ICP: 0
I pulled the IPR (that was only a year old) and the screen was perfect. I had 11.5v at the plug for the IPR, and on the Ohms scale I was reading 1.8Mohms.
I went to the dealer and got a new IPR, and still no start. and the only change in the reading on the scan gauge was the ICP is now reading 56. The gauge on the dash is reading normal oil pressure, but I haven't checked actual Low-end oil pressure.
Last month I replace the HPOP, and 1 faulty injector. Now I thinking wire loom, defective new IPR from the dealership or the new HPOP has failed.
View 5 Replies
So today I was driving down the highway and my engine shut off. No sputter or any thing I had just filled the tank. I tried to start it and it wouldn't start. It's been hitting a dead spot at around 3000 rpm like its not getting enough fuel or something. Right now I'm thinking it's an ipr valve but would like to know if what was the cause and how did you fix it...
View 10 Replies
I just got back from a trip across the state to see the Miami boat show! Truck was running just fine on the trip over, EOT/ECT delta around 9* (seems a little high to me, Im hoping because im running 35's, but can someone back me up on this?)
On the trip back, cruising at 70, I noticed the check engine light went on... I didn't have it under heavy throttle or obscure circumstances... My ScanGauge 2 showed that I had a P0299, which as Ive read means something relating to underboost?
I cleared the code. And the CEL never showed again in the last 100 miles... Could this just be a quirk? Or should I be more worried about it?
View 14 Replies
So I was driving down highway when I lost power. Engine was still running just had no power and would blow black smoke when I got on the accelerator. I pulled the EGR valve and noticed it had rocks stuck keeping the valve open. Cleaned it all up and put it back in. Went for test drive and seemed good again until few miles in same problem. Took it apart again and same thing.. rocks. I did this 3 times with same results...rocks getting stuck in my valve.
View 1 Replies
I have ran 05 f250 and the wrench light keeps coming on mostly when I'm doing highway driving or when I go to pass someone. iv putt code readers on it(autoparts store readers and the good expensive ones)and i keep getting bad egr and some other codes but when I have the truck looked at everything is prefect I had a flush done on the truck and and it still comes on randomly . Could the fact that it needs an oil change cause the light to come on intermittently or is something else going on??
View 8 Replies
2007 f250 6.0 .... I just had the wrench light come on while driving on the hwy. wasn't towing, or hauling anything. Just traveling around 70mph for an hour or so. I didn't notice any change in power. Got to my destination and cut the engine off. Couldn't pull any codes with an OBD II scanner. When I started it up again, light was gone. Owner's manual points to electronic throttle control, not much else.
View 14 Replies
I've been noticing some weird, very subtle engine sound changes while driving at highway speeds lately. Something almost like surging, but not. I don't know how to describe it. I might try to make an audio recording next time I take it out so I can explain it.
Anyway, I don't know why but ICP popped into my head. Maybe, for some reason, the engine was varying ICP causing the surging sounds.
So I hooked up AE and did a test. I've attached a screen shot.
With my idle speed actuated as high as it will go, and ICP actuated as high as it can go, I can only get a pressure of about 1450 PSI. I always thought ICP should go higher than that. I seem to recall reading somewhere around 3600 PSI.
So am I misinformed, am I reading the data wrong or do I have a problem? How high should Injector Control Pressure go? I missed it in the screen shot, but ICP is actuated to 100%.
View 14 Replies
I was driving down the highway when I lost all oil pressure soon after I lost power steering and the engine died. I have checked the radiator and it is still full of fluid pulled the starter off and try to crank it it still turns the cannot get the engine to turn over it clicks but wont turn over there are no oil leaks underneath the vehicle that I can see. I'm just not sure where to go or what to do from here
View 19 Replies
I was driving on highway about 55MPH when I lost power suddenly. I was able to pull off, but did not have power brakes or power steering. Gas tank was near 1/4 gallon on the gauge, but sometimes my gauge is wrong, as I've run out 2x when I should have still had a few gallons in it.
At first I thought CPS, but I didn't have a spare with me to swap. Well, after an hour or so, I cranked it, and it would turn over but not even try to start. I floored the gas pedal and it fired up and I was able to get home.
During the no start issue, there was no oil pressure reading on the gauge and the tach was not moving, even though it was turning strong. There was no white smoke that I could see either.
View 14 Replies
Last night when i left work I noticed my fuel pressure was running about 77 psi, it normally runs about 68psi. today I took my daughter to practice and it was around 83psi, on the way home it was up to 95psi, so I parked it and took another truck to work.
About a week and a half ago I lost fuel pressure going down the highway and the truck died, finally decided my pick-up foot must have come off and had my sister in law bring me some diesel and it has drove fine ever since. (it was right at a quarter tank).
I have the FRX from riffraff and am thinking some pieces of that foot have got into the fuel bowl and plugging up the return. Things to check? Could it be a problem with the fuel gauge or wiring, and how to test them. It is an autometer gauge from riffraff.
It will probably be a few weeks before I can do much more than clean out the fuel bowl. I don't have anywhere inside to work on it and it's been rain/sleet/freezing rain/snow for the last 10 days. I have most of the stuff to do the hutch mod and its next on the list but was hoping to put it off till spring.
View 13 Replies
