Ford 6.7L Power Stroke Diesel :: Truck Kept Rolling Slowly / Pedal Rock Hard When Apply The Brakes
Jul 20, 2017
Have 65k now..OEM breaks. Never an issue.. going along today had to make a fast turn left into a parking area. Hit the brakes doing about 50 made the turn. Slowly found and kept rolling to a parking spot. Went to apply the brakes and found the pedal was rock hard. The truck kept rolling slowly. Pure luck I was were I was.. I tried to shut the truck down and restart. Still rock hard pedal in up position. No breaks.. not enough to stop at idle. Checked the brake fluid and it was fine. Went inside the store to grab the delivery and when I came back out I tried to work the pedal down.. I felt some give.. put it in reverse to check it out..(couldn't go ahead no room.) slowly the breaks came back. Has been fine since.. driving all over town today. No codes or engine lights.
View 14 Replies
Advertisement
I have a 1997 F250LD 4WD. I was driving and came to a stop light. I hit the brakes and the pedal was rock hard with what seemed to be very little travel. I pushed hard to get to a stop and the abs activated and I came to a slow stop. This has happened about 3 times over the last 1000 miles of driving. I see no ABS or Engine lights. Most of the time the brakes are normal. Pads are fine, fluid is fine. Brake booster seems to work fine, pedal is not mushy or hard to press other than the 3 or so times this has happened. Once this happens I can let off the brake and everything is normal. I have not found any vacuum leaks.
View 6 Replies
I have an ABS issue. Coming off the free way ramp my abs will engage when I apply the brake peddle. This only happens turning right. doing the same to the left seems to feel something but not as apparent as to the right. I have no ABS light on and no code.
Last year I replaced the left front wheel hub. but didn't have any issues until this. One more thing I was getting a feeling on my brake pedal last week as if my front rotors needed to be replaced. So I did. Rotors and pads. still feel the same. could my rear rotors need replacing as well?
View 14 Replies
Very weird thing happened on the way home from work. When I left work (not to full temp) at about 1500 rpm and 30 mph (had to be at 30mph--seemed to be the key) the whole truck felt like it was rolling across rumple strips (the ones one the shoulder of the road) all vitals were normal and it was gone once on the interstate and up to temp (I did gon on it to blow out anything that may have needed to be) it felt more like drive line but honestly can't say. 2006 F350 4X4 ....
View 7 Replies
I just got my new up pipes put on as well as a 38R and pulling a hill hard my truck will hit about 22 psi then drop off slowly I have an electronic boost fooler wich has been on the truck since new pretty much but I don't get a CEL at all is this what I should be getting and I was on the 80hp tune? I ordered new boots and plenum inserts they just haven't got here yet. I know I had a leak before on my old up pipes because they rattled every now and then and I could see exhaust coming out of them when it was cold out but I could hit about the same 22 boost with my old setup. So pretty much nothing changed boost wise except it gets up to boost faster now. I would say it's defueling but I was always told the CEL would come on if that was the case.
View 13 Replies
If I am going over 40 mph and I have to brake hard my truck pulls really hard to the right. I mean so hard it will take me off the road. My truck is a 2004 f250 with 147,000 miles.
In the last six months I have replaced both hubs, rotors and brakes. I really drive like an old man so I don't know how long I have had this issue. Just someone pulled in front of me on the freeway and I had to brake hard and I found this out.
I have checked both front capilers and brake lines and those are fine. I have brand new tires on it. I really have no clue what is going on. I have pulled the brakes off three times and checked everything out and it looks good. If slowly push the brakes everything is great, it is only when I have to really slam on them.
View 13 Replies
Had 3 separate episodes dead pedal on my 04 bone stock 6.0. About a week ago I pulled out on the road and the truck went to idle and would not respond no matter how much throttle I gave. After about 10 seconds it woke up and took off. Had this happen 2 more times this afternoon.
No codes or dash lights.... What this might be? I have a 500 mile road trip this weekend and am worried about being stranded on the side of the road.
View 14 Replies
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 Replies
I was parking my truck and the brakes wouldn't depress and I almost crashed into another vehicle that was parked.
View 14 Replies
I'm posting this for my neighbor who has a F250 that's 8 years old. He has replaced many parts, engine from what I know but now when he starts the truck it starts fine but as soon as he starts the truck, the brakes lock up. He can't move it. He hasn't had the chance to move it because the brakes lock as soon as the truck starts. It starts fine and idles fine but can't move because the brakes are locked. Tomorrow the tow truck will haul it to the ford dealership so they can look at it and run the diagnosis computer on it.
View 4 Replies
On Saturday I drove my truck 450 miles, all of it towing, in hilly New England. The turbo boost gauge was operating at 20psi or higher for many of the hills, and the 13mpg average was indicative of how hard the truck was working (normally empty I will get 20+). The next day, I drove it about 3 miles and it started a regen. Why? Wouldn't it have been passively regenerating for most of those miles? A steady 75mph for hours at a time?
View 14 Replies
I have a 2006 that shuts off in a hard pull, if I wait 3 minutes it starts again. I hooked up my scan tool and when it dies and I crank it it only builds 200psi oil pressure, let it sit it builds enough pressure to run fine. If I dont push it over 3500psi for more than minute it wont die pull a hill it dies again. Is it the hpop or an o-ring.
View 10 Replies
Earlier this week the truck was hard starting every time. Tested the batteries: 12v engine off, 14v engine running, all good.
The next day it threw a P0284 – Cylinder #8 contribution/balance, and was clearly missing on a cylinder. Despite the lack of a puff of smoke at start-up, I was pretty sure it was an injector. So I ordered one from White Bear Lake, and a fuel pressure test adapter from Strictly Diesel. Then I decided to do some testing with AutoEnginuity. Tried the injector buzz test first and got a note that the truck was not capable of performing the test. Tried starting truck and gauges swept and wouldn’t turn over. Tested batteries again: main battery 11volts, aux 12volts.
I got the batteries in and the stupid thing runs like new. Only codes are P1000 and P0603. Truck passed the injector buzz test, and cylinder contribution test graph is almost a flat line.
Take-aways:
1. Bad batteries can cause all sorts of havoc.
2. Always use a voltmeter that displays tenths of a volt, because if it’s only showing whole volts, it could be rounding up. The 12 volts from my first test was probably more like 11.6 volts.
3. Always do as much testing as possible before buying parts.
4. Costco does not sell Kirkland batteries anymore. They only stock Interstate, and the Interstate warranty has dropped from 36 months free replacement to 30 months.
5. The Walmart and Autozone batteries with the five year free replacement are “out of stock” and I’m guessing they won’t be back with Interstate dropping their replacement dates.
6. Most of the car batteries in the US are made by Johnson Controls.
7. Motorcraft batteries did not get very good reviews.
8. Interstate said that AGM (absorbed glass mat) batteries stand-up better to the additional vibration and heat experienced under the hood of a diesel, but they are significantly more expensive, and not all the brands offer an AGM with a better warranty than their best lead-acid offering. Also, the guy at Sears said AGMs are only beneficial for newer cars that continue performing electronic functions after the ignition is turned off. He said he’s seen lead-acid batteries outlast AGMs, but didn’t specify if those were out of diesels or not.
Questions:
1. Can I expect the P0603 to go away after the drive cycle is complete?
2. What should I do with the new injector? If I return it there’s probably a restocking fee. If I wait for a complete injector failure I don’t get the core charge back until then. With the FICM compensation, I don’t know of any way to identify weak injectors without IDS.
View 14 Replies
So since I bought the car several months ago, I have been noticing something about the braking. Every time I get in the car the brakes are ROCK hard until I start the car, this seems abnormal to me, I never experienced this. That is not the only problem, when I am driving down the road and go to apply the brakes there is a hesitation which causes me to press harder and then the brake kind of slam on. I know its under warranty but I hate taking my car to the dealership so I'd like to know first that its a legitimate problem before I take it to VW. I know about the Hill assist, this isnt part of the issue.
View 24 Replies
My brake pedal is rock hard to press and when I do press it while pushing the push to start, it does not turn on.
View 8 Replies
2011 F-350 XL, I can hear a squeal coming from the front brakes when rolling forward slowly, believe the pads are dragging on the rotors. If I touch the brake pedal the squeal stops as it does when I turn the wheel. Took the calipers off and greased the slide pins and put it all back together, still got the squeal. What don't I know???
View 9 Replies
Can get up to speed about 55-60 in my 2003 f250 6.0 4x4 truck and hit the brakes hard and the pedal gets hard almost like you cut the truck off and the truck doesn't stop well I can let off the pedal and hit it again hard and it works like it should. Also when it does this the power steering doesn't work. I was on an exit ramp and almost wrecked when I exited off the interstate I hit the brake pretty hard and couldn't steer I let off the brakes then hit them again and it worked fine and so did my steering. It would seem that the two are connected somehow. What's wrong?
View 2 Replies
I have 2011 SE, it won't start at all. The car won't start all thou all electrical are working (radio, NAV, Dashboard) but when trying to press the break pedal is hard as a rock. Dashboard computer at times tells me to press the break pedal - but it wont start, it actually turns off when i press the break and hit the start button. It happen twice before was able to start it within couple minutes.
View 24 Replies
2000 Ford Excursion, 7.3 PS with 210,000 miles. I am on I40 at a truckstop. I was rolling down the freeway last night when the truck started bucking. I pulled of the freeway and here came a thunderstorm. I waited til this morning to check for codes cheap scanner. I pulled a code P1211. I waited for NAPA to open so I could take it in the shorts. I bought a fuel filter and an ICP sensor. After changing them out, the truck runs then starts missing. My battery is about to die so I will finish post shortly.
View 14 Replies
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
View 10 Replies
I was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 Replies
