It just came on when I ran up to the gas station followed by the airbag light and the traction control light.. truck ran fine. I've tried looking this up found some people have had this message and there truck won't start.
View 6 RepliesBrought my truck (2012 F350) for recall service for one of the faulty exhaust temperature sensors. It took them one week to replace the sensor (!), then when I came to pick it up I got: "Trailer Brake Module Fault" message on the display.
I have never seen this message, since I own the truck (I am original owner). The service adviser said it will take a minute to reprogram the module and took the truck back to the shop. Came back after a while, saying that it didn't work and I need to leave the truck, so another technician can work on it tomorrow. Tomorrow came and I got the call that they reprogrammed the module, but the message still shows up, so they need to work on it (another day!).
As of now they still don't know what is going on. Apparently they broke something while replacing the EGT sensor and how to fix it.
I'm having some electronic problem with my 350. I parked it and took both batteries out for about a week. I put 2 brand new ones in and hooked them up truck won't start. So I turned key on and left on and the fault that comes up is the "trailer brake module fault" also the abs light, parking brake light & passenger airbag lights are on. Sometimes if I leave key on long enough the lights go away and I can start the truck. But it shuts down during idle. I unplugged the tbc (indash) and the #22 fuse under hood and #31# on passenger side. Still showing the fault. I'm not being allowed to start the truck. I used my tuner and found one code (P0884 tcm power input intermediate)..
View 14 RepliesHooked up the toyhauler Friday and before we were off of our street I got the "Wiring Fault on Trailer", brakes on trailer worked, got out and verified the lights were working so we proceeded on.
When we got to the destination the manual says that if the fault stays on when disconnected it is an issue on the truck side, it is still on when the trailer is disconnected.
I only get the fault when backing up. Driving forward it's never a problem. The truck is a 2015 F250. We are pulling a 33' travel trailer. Both are new. I was not sure if the fault when backing was something that happens or if it might be indicative of a problem. The manual says it's not an indicator of a problem. Rather, there might be an issue. Again, it works fine when traveling in a forward motion.
View 10 RepliesI have 2 messages showing up in the message center / control panel. I have taken the truck to the dealership and we cannot recreate them while the truck is at the dealership. How it can be resolved.
2013 Ford Superduty Platinum : 33,800 miles and the truck is stock
Messages : service traction control / Downhill decent control fault
This will happen just driving down the road or just after starting the truck and taking off.
It has happened towing my work trailer and also not having the trailer connected to the truck.
I have a 2012 ford 150 what fuse controlls the trailer lights.
View 2 RepliesI have a 15 F350 DRW 6.7 pulling a 19K fiver with 8K axles and disc brakes, I have to have my brake controller set at 10 to get the brakes to work well. The pads are good, just bled the system using a power bleeder, controller is set to electric over hydraulic with max gain. Why I need to have the controller set to max?
View 14 RepliesI still have my 2011 6.7 f350 CC. I have a triple axle (single wheel) gooseneck tilt deck trailer that I pull my older dozer and backhoe on.
With the trailer brake gain set to 10 I don't have as much brake engagement as I would like. It actually wont lock them up at all when adjusting the gain. Loaded I don't feel any engagement when manually sliding the controller.
On my sons 99 f350, with after market controller he can adjust his output so that the brakes engaugelock at just about any adjustment (way over breaking) so I believe the trailer brakes work fine, I just don't get enough output from the factory controller.
Is there any additional adjustments the factory controller has or any suggestions to increase the output more so the brakes have a bit more engagement?
I have an issue with my 2011 SD. When i press on the brake pedal I get a message saying I have a trailer connected and then when I step on the brake pedal again it says trailer disconnected. This happens every time I touch the brake pedal. I have replaced the trailer connector 7 way plug thinking that was the issue to no avail.
View 3 RepliesOk 2011 ford f350 6.7. Turn key on, no crank, no start. Trailer brake module failure flashes on the screen. If you leave the key on after 5 to 10 minutes the heater kicks on and you can start it. Runs down the road, hitting every pot hole for 1000 miles fine. Shut it off, try to immediately restart, same thing. If you hook up a booster box to it it starts. Replaced both batteries, cleaned cables. Scanned it, only codes are with the instrument panel : loss of communication with trailer brake module, with abs, with heat and air, and with parking aid modules. Tried to scan abs, parking aid, and brake, scanner would not communicate. When it is running communicates fine with them. Need a direction to go from here?
View 14 RepliesAdding a third axle to my dual axle 5th wheel toyhauler... was told I may need a different brake controller by someone on a different forum.
At first I thought they were talking about the one in the truck but I would guess the truck brake controller can handle atleast three axles worth of brakes. Now I am wondering if I have another "control box" on the camper somwhere.
I see many people pulling 3 axle trailers and I would assume you have brakes on all 3 axles. Am I good to assume the stock Ford brake controller can handle 3 axles with brakes on all of them ??
Does a trailer/toyhauler/camper have another "control box" somwhere that regulates the brakes as well ??
My 2012 F250 6.7 once again (third time in 2k miles) got stuck in park with no brake lights or traction control. I found that removing the shroud from the steering wheel allowed me to manually activate the solenoid and get into gear but could only drive in manual shift mode.
Something is causing the brake switch fuse to blow. When I replace the fuse all is well for maybe 1k miles then it happens again! After the second time I replaced the brake switch thinking it was the cause but no deal. It happened a third time. The dealer who fixed it the first time could not find the cause.
This is frustrating and downright dangerous! What in the circuit could be causing the short?
Been having a on/off problem with my trailer lights. Some times the right hand side does not work, them it starts working. I thought it was my trailer until I rented a bobcat this weekend. They couldn't get the right side lights to work.
I stopped by my Ford dealer and a service tech came out and checked out my pigtail. All checked ok. It seems odd that both trailers would not work on the right side. Two different types of trailers. One is my RV, the other was a flat bed for hauling the bobcat.
Borrowed a buddys trailer that had wiring issues. I ended up blowing a mini fues & maxi fuse in my truck. 06 F350 CC ... Replaced both fuses in the truck and had park lights on the truck but now dont get any lights on any trailers. All factory plugs 7pin & 4 pin. I get turn signals and brake lights on the trailers but that is all. If the fuses are good were should I start looking for problems? or is there more fuses I may be missing. I have metered all the fuses under the dash aswell as under hood all check out. Where to go next ???
View 14 RepliesMy trailer wiring is not working, at least from what I can tell. Embarrassingly, I know this because the little brake light I have in my trailer hitch no longer lights up. I've tried different bulbs and a different unit, so it's definitely the wiring. I do not have access to a trailer right now, so unfortunately that's all I have to go on. It's plugged into the 4 pin jack. Is this something I should be going to the dealer for, or more like a blown/loose fuse or something?
View 13 Replies2010 F250 Lariat, cab and a half, PSD. 5600 miles.
Sunday I started the pickup and received "trailer brake module fault" in the message center. I wasn't pulling so wasn't too concerned - hit the reset and continued on.
Sunday night I started the pickup again and received the same message followed by "check brake system". I also lost illuminated gear selection, the traction control active symbol was displayed and the traction control "off" (PB) was illuminated. After several attempts it reset, everything returned to normal and I was able to get home without incident.
Monday morning it wouldn't start. It indicated "trailer brake module fault", "check brake system", traction control active and off, no gear indication, the odometer indicated "-------" and it did not react to the key in the start position.
Tuesday morning I attempted to start and it was the same as the previous attempt. I noticed that the theft prevention appeared active (flashing) so I removed the key, locked the doors, unlocked the doors, tried again - no joy.
I kept trying while holding my mouth in different positions and finally by the grace of God it fired. I delivered it to the dealer.
The dealer called yesterday afternoon and reported that everything is a result of a bad trailer brake module. The new one is to arrive today, they will install and everything will be peachy.
I asked if they could just unplug it and reprogram the truck to believe it never had one - the service writer said it can't be done, different piece parts on trucks with or without trailer brakes.
I really have no choice but to push the "I believe" button and carry on but I am slightly concerned. The fact that the trailer brake module can cause catastrophic failure doesn't seem too cool, I don't have a real warm and fuzzy feeling associated with venturing far from pavement, reliable communication or alternative transportation.
In the meantime I suggest that no one take "trailer brake module failure" lightly.
Hooked up to a bumper hitch trailer tonight with my 13 F350 and didn't have any lights but the brakes worked. Tested the bumper hitch trailer connector and there was no power on any terminals, with the tester still connected to the same ground I checked the trailer connection in my bed for my gooseneck trailers and everything was working. Just to check the trailer I hooked up my wife's 2015 F150 and all the lights worked. Can't figure out why my gooseneck connection works but not my bumper connector, also looks like my license plate lights are not working either.
View 14 RepliesIs there a fuse or something to check? All other lights work, just book the running lights
2006 f250 4x4 CC
2005 Excursion 6.0 with normal bullet proof mods... towing 6000# dual axle enclosed race car trailer.
I've been towing this same package since 2008 all over the eastern half of the US and averaging right around 10MPG.... hand calculated from fill up to fill up. Sometime a bit more on a flat run to Daytona, or a bit less through the mountains... but very close to 10 MPG.
Well the factory trailer tires finally wore out and I replaced them with 8 ply Maxxis M8008 trailer tires...... highly recommended by the camper crowd.
Since then, I've been round trip Baltimore to Pittsburg, and Baltimore to Daytona (total of 2500 miles) and I've been averaging a bit over 12 MPG consistently..... again hand calculated. Same package, same highway speeds.... nothing has changed in my towing style.
Seems almost to good to be true. At this rate the tires will almost pay for themselves by the time they are worn out. Any trailer tires make such a difference ?
I have both a hydraulic dump trailer with two 12v batteries and an RV trailer with two 6v batteries to supply 12v. Both trailer's batteries are wired to be charged from the tow vehicle if the TV is equipped with a charge line.
Does the OEM 7 pin connector on a 2005 Ford 6.0 F250 CC 4X4 have a charging line on it? If so which terminal / pin is it?
What gauge of wire is it and how much amperage will it deliver to the connector? For testing, when is it hot? When the truck is running only? When the key is on? Is it hot all of the time?