I noticed a slightly higher RPM at idle (1100-1200) with outside temps in the mid 50's after a 15 mile trip. I dont recall what it usually is, it just seemed to revving higher. What would say normal RPM's are on a warm engine.
View 8 RepliesI got a "P054F- Idle Control System - Fuel Quantity Higher Than Expected" this morning and again this afternoon. I did a search and the only threads that contain the code are the codes lists and one guy who got the code but no follow up. I found a few instances through Google, but almost all of them said the dealers just reset the code. It seems to happen in cold weather, which we are having. Both instances were in the same situation, remote start warmed up then short town drives. No CEL came on. Anyway, I reset it and I'll see what happens.
View 10 RepliesI've got about 1100 miles on my new truck now and I will be heading to S.D in a week or so towing my car hauler with FJ40 on top and camping gear. About 10 000 pds.
Would it be wise to dump the factory oil and go with 5w40 Rotella? It has been getting really hot here the last two weeks and its only getting hotter as I drive south.
I purchased my 2013 F350 PSD July of 2014 and immediately noticed "the shudder" when the engine was lugged down to 1000-1100 rpms on a hill. Sounding like somewhere around the turbo belching air too. At first I was startled but learned to manually downshift to higher rpms and it will stop. Once or twice I tried accelerating out of it and it shuddered as bad as the poster who said it made the steering shudder too.
My truck has 16,000 miles and I never let the rpms drop now. So I figure I have a real problem I'm not imaging. What should I tell my dealer is the TSB or remedy ?
03, 2.3 duratec, 163k, new timing chain, plugs (AP104), wires and intake. cleaned MAF, air filter, and ran two cans of sea foam through the intake and its still pinging. its driving me up the wall. truck runs perfect but seems to idle slightly higher and take longer to come down to idle after I got the timing chain and plugs/wires done. I've sprayed starting fluid around on top of the engine looking for vacuum leaks but found nothing. What should I try next?
View 14 RepliesTook a trip today that was 3 hours there and 3 hours back. Truck ran normal on the way there (eot about 202 and ect about 196-198), but on the way back truck ran a little hotter than normal (ect as high as 214 eot stayed within 2-3* plus or minus ect). Fan did kick on every time I hit ect of 212 and would drop it down to 196-198 and oil temp would drop at the same rate.
Truck is stock 190k miles with a bulletproof egr cooler and coolant filter. Oil cooler probably has about 20k on it. (4th one on this truck- since I like changing them out as much as the rest of us). I checked coolant level when I got home and I might've added a pint to get to bottom of sticker. I'm not sure it wasn't a pint low when I did last flush and cooler replacement.
No puking and I can't find any leaks. I pulled egr valve and no moisture in manifold just a worm out o ring that'll I'll replace. I can't find any leaks. Where to check that I haven't? I don't feel like I'm losing coolant because I wasn't really low. My fan never failed to kick on when I hit 212 or stopped at a red light. No moisture in manifold so I'm not thinking losing coolant due to head gasket. Maybe radiator looks ok but tomorrow I will blow out any bugs to make sure.
At idle it stays at 48.5v-47.5v But as I pick up speed it continually drops. At 70mph it gets as low as 29v. But will go back up slowly as I let off the throttle.
View 8 RepliesTruck has an SCT tune from Innovative Diesel.
View 6 Replies I just bought a 2007 6.0 with 239k miles on the truck, it has EGR delete and ARP head studs. When i bought it the owner warned me of injector stiction...
I drove the truck for about a week, changed the oil over to Rotella T6 with archoil, and swapped out the air filter so far. (previously was non synthetic rotella). I drove the truck 2 more times since changing those two items and then i had a no start issue.
Scanguage2 said it was FICM sync.....so i messed with the wire loom, and got it to start twice but it died right away. (it had ficm sync, then it died and went back to 0) So i ordered a CPS pigtail and was going to change it out today.
Today i went out and pushed on the CPS sensor directly, charged both batteries and the truck started rough but kept running after two times (still haven't changed the pig tail)
Now it starts but is still running rough.
Scangauge 2 Running:
IPR : 23.8
ICP : 581
FICM SYC : 1
FMP : 48.5
The only code i'm getting is P0269 which I'm hoping is only injector 3, a bad injector wouldn't cause all this would it?
I'm just trying to figure out what i should look at next.
Started having some crank no starts intermittently. Scanned and found codes for cam sensor. so I was in a pinch and a hurry on a sunday so I picked up a BWD brand cam sensor from parts store and installed. I have not seen this issue since but started noticing other thing going on. I noticed a few weeks ago my truck was starting a little strange. as it would spin over before firing off, it didn't sound right. I couldn't pinpoint if it was due to slightly low compression on one cylinder or one cylinder had a little fuel or oil in it and that one cylinder was actually firing while cranking over.
I also was noticing a little longer crank times than normal. didn't matter if engine was cold or hot. sometimes would fire up quick and sometimes it took a few seconds. most of the time I couldn't catch it on my scanegauge if the ICP was low due to the lag on the scangauge.
Well one day on my way home from work (50 miles one way) I stopped about half way to fuel up. after filling up and attempted to restart the truck it really acted like it didn't want to start but did after cranking for about at least 10 seconds and started rough. and of corse my scangauge decied to hate me this day because it would show any data until I unplugged it and plugged it back in. so started home. felt like it had a very very light miss on the way home. when I slowed down to turn onto my road the truck died. took forever to get it to start back up. this time the scangauge was reading and I could see ICP was between 300-400 and IPR was 85%. so low pressure and not reaching the 600 needed to fire. once it started I limped it home. scaned it with my Auto Enginuity and it didn't show any codes.
So that much I can see I have a leak on the HPO system. but I done a lot of work to the truck about 2-3 years ago. roughly 80k-100k miles since the work. what I done included...
OEM oil cooler
OEM (updated)dummy plugs, standpipes & STC fitting
OEM head gaskets and ARP studs
BPD EGR cooler (I should have deleted)
ALL other engine gaskets(Bed plate, oilpan, front&rear cover, ect.)
OEM glow plugs and harness
OEM blue spring upgrade
Cleaned turbo veins
2 OEM REMAN injectors. (cant remember which two) had contribution codes one on each side.
This is all I can remember right now. Now have yall seen the updated dummy plugs and standpipes leak? I have not pulled valve covers to air test the HPO system yet.(don't have my air compressor at my new house yet). Here is what I have done so far:
Fully charged batteries.
I did do a bubble test. pulled upper fuel filter cover off and removed filter topped the bowl off and turned engine over using the wire by the passenger side battery. some bubbles but not a bubble bath.
Checked fuel pressure (not running) its 60psi. did not start truck because I need a different fitting so I can run the truck and check pressure while running.
while doing the bubble test I could hear that one cylinder is low on compression. but I do not have any misfire or contribution codes.
when I ran contribution test on AE its not showing any particular cylinder lower than the rest. but the line is not very solid at all.
Here is what I plan to do.
Compression test on each cylinder.
Looking at the Harbor freight kit. Looks like it has fittings for glow plug and injector holes.
If I can do compression test on both glow plug and injector holes this should show weather my injector orings are the cause of the low compression.
Then I have to airtest the HPO system and find the leak.
Am I on the right track? what else should I check? Guess I should add that the truck currently has 297K miles.
Ok, so I have a Viair onboard compressor supplying air to airbags, train horn and fitting in the rear. With all that, I have multiple connections and some leak ever so slightly making the compressor cycle ever few hours. Question: Is there some sealant I can use with push on fittings and connectors to eliminate the leaks?
View 9 RepliesIt's on my 2015 f-250....dont know if this is a new thing ..... I know my 2011 f-350 didn't have it..... Really hardly notice its working ....it slightly slows me down when in tow/haul mode while braking......
View 14 RepliesFor the past month or so I have had something strange going on. When driving between 65 to 70 on the highway, I've turned my steering wheel slightly to the right and if there is a cross wind or head wind there is a vibrating sound. And it does get loud. I don't really feel it in the steering wheel. Only when there is a wind. I haven't done anything new to the truck since winter.
View 4 RepliesI have a 2011 f250 crew cab lariat that actually sits about 3" higher on the passenger side in the rear. I never noticed until I put some 4" pro comp blocks on the rear. I measured before and the rear left was 40" and right was 41-3/4". Now the drivers side rear is 42" and rear passenger side is 45"? I have looked at the blocks to make sure they are seated properly and everything is installed correct so what gives? What could be causing this. I bought the truck with 99k miles and now it's at 130k miles. I do tow a small cargo trailer sometimes but it is only about 3k lbs. Now I am thinking of buying some new leaf springs to see if that corrects the problem.
View 4 RepliesHave a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesI recently bought a 2004 6.0 extended cab truck. It has 223,000 miles on it and has been running great. Bought it here in Arkansas where I live and recently drove it to Texas and back after having just put some Hot Shot oil treatment cleaner in it. I ran it the 1000 miles as it suggests. Just the other day as it was hitting the 1000 mile mark the truck started to lunge/runaway and stalled. I finally got it back home and started looking into the issue. Based on what it was doing, (lunging/running away, and at idle in park random burst of rpms and then dying after doing it a few times), I started to do some research. Most of the answers I found claimed it was the IPR valve. I found that the IPR valve is supposed to, as claimed by some, be pulled and inspected every 100,000 miles are so and if need be replaced or the rebuild kit gotten for it. So I decided to just replace it as well as the oil, oil filter and fuel filters.
When replacing the IPR valve I noticed that it was original and that its screen was missing. I didn't have any problem moving the little piston in the center of the shaft with a small bolt however that doesn't really mean that it isn't bad. I tried a magnet to see if the screen was still in there and nothing came out. I did not try using a camera as I do not currently have one, to look inside the port to see if I saw it. After replacing the IPR valve with a brand new one and changing the oil I started the truck. It seemed to be running a little ruff so I let it warm up. Not one minute later the exact same thing started happening, lunging/running away (random increase and decrease in rpms), so I called it a night. The next morning I decided to change the fuel filters. No that it matters the order in which I did it, but I changed the top end filter first and the the one on the frame with the dealer recommended OEM filters as was the case with the oil. I did find in the filter on the frame that there was a small amount of sand and clay soil looking matter in the filter. I did clean out the filter housing as well.
After replacing the filters I started the truck to warm it up. I noticed that it was still running a little ruff but no random, lunging/running away (random increase and decrease in rpms). However after five minutes it started coming back. I finished letting the truck warm up and took it for a drive. Got it up to between 7-80mph for about 15 miles to try and see if I could "blow out" whatever may be in the fuel if that was even an issue I do not know. The truck seemed to get more power and run a little more smoothly so I stopped at my buddies house not to far from where I was and let it idle. No issues other than a little ruff idle. After about 10min I took off towards home doing similar speeds. I noticed at a little over 2000rpms that the truck was shaking a little but so I dropped the speed down. When I got home not more than one min after idling the same issue, lunging/running away (random increase and decrease in rpms), started happening again.
At this point I took back to the interwebs and came across a post that said the ICP might be bad and does cause this issue, lunging/running away (random increase and decrease in rpms). However I also noticed that this is a huge debate as to whether or not the ICP can cause this. Ford master mechanics say no and other mechanics say yes and round and round it goes. I decided to do the simple test many recommended which was to simply unplug the ICP and see if anything changes. Things did change. No more lunging/running away (random increase and decrease in rpms). Not more than two minutes after plugging it back in, allowing the computer to account for it now, the lunging/running away (random increase and decrease in rpms) came back. In the middle of it doing this I unplugged it and that went away. So needless to say I replaced the ICP and voila the lunging/running away (random increase and decrease in rpms) is gone but the ruff idle is still there along with a slight loss of power.
To answer some questions:
1. The oil and water are not mixing so I am almost positive that the heads are fine
2. The intercooler couplings are leaking a bit. I have ordered the new ones and will replace them as soon as they come in. Can this cause the issue?
3. I am blowing no white or black smoke except for when the lunging/running away (random increase and decrease in rpms) issue was present and the truck almost died. It would knock occasionally when it almost died and would send a slight puff of black smoke which I assume is a low or high fuel issue from the truck trying to die
4. I have not had the no start issue at all
5. I did not see any debris in the oil during the oil change
6. I didn't do the air test on the ICP port as I do not have the adapter.
7. The only code I got on the IBD II port was when I unplugged the ICP which was to be expected
8. I found no damaged wires
I am at the point where I am wanting to take it to ford to have them run a diagnostic on it but am wondering if there is anything else I need to be looking for. Here are a few questions I have.
1. Does this sound like a bad injector? (When I bought the truck it would sound like a misfire or ruff idle condition was present for about 5-15 seconds and then it would smooth out with no issues. It would run a little ruff if you tried to take off without letting it warm up, which I did once or twice and low rpms, but when it warmed up no issues were present).
2. Could this be the HPOP?
3. Could this be the FCIM? (The previous owner had replaced the FCIM not to long ago with one from Ford I believe. Said it cost him something like $700)
4. Could this be something clogging the oil screen under the manifold?
My final question right now is do any of you know where or what brand OBD II reader or software I can get for a decent price that will tell me the voltage of each injector and FCIM is without me having to go to Ford to get it looked at.
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 RepliesI have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...
05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.
This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....
Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.
However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine
Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 Replies