My truck has done this since I got it and it's pretty damn annoying. While at idle the rear view mirror vibrates slightly and drives me nuts. If you give it any gas at all it stops. Like I said its super slight but it's enough to notice for sure and makes stuff look blurry if your looking through it.
View 5 RepliesI have an 03 6.0 Power stroke. My problem all started the other day when I started to occasionally not get any boost on acceleration and lose of power and a lot of vibration like it's about to cut out but it got worse now today I drove it about 5 miles into town when I got to town I noticed a rough idle I got gas in a gas can not in the truck. I got back in to leave and I had absolutely no power at all the truck stalled out and it was very hard to start finally got it started and it runs really rough almost like it's going to shut off.
So when I started driving I would only make it about a mile or so with out it chocking out and having to let it site for a minute or two and start it back up and go another mile or 2 and have it do the same thing all the way home all the time I have vary little boost if any at all except for when I first pull out now oil pressure is good and engine never over heated some of the codes I have is an EGR code and a contribution balance code for several cylinders I was thinking possibly a maf sensor or a clogged egr not working right.
I am having an odd issue that i don't want to turn into a bigger one.
When I am sitting at a stop at idle and have the brake pressed i hear a humming sound and the pedal vibrates but when I am moving an press the brake it doesn't do it. Ive checked the pads all around they're fine brake fluid is fine it didn't start doing this till a few days ago.
I am just trying to figure this out before i end up going down the road one day and go to stop and have nothing there.
My old flip style rear view mirror was getting a little bad looking on the bottom of the mirror, so I decided to go pick up an OEM auto-dimming one. I did not care for homelink as I have no need for it, nor do I need temp since thats on the car already, so I wasn't interested in a non oem mirror. Plus I like simplicity, so plug and play is always nice. I paid $70 for the mirror, you can expect to pay around that as well.
Anyways, from my understanding, our Camrys should come prewired for the auto-dimming mirror, or at least the sunroof equipped models should come prewired. The plug sits in the overhead console near the drivers side sunvisor taped down. It's just a little white plug with a black sheath around the wiring.
Tools Needed:
-Your hands
-A smallish hex key (I don't know the exact size) or a smallish torx screwdriver
From start to finish, this shouldn't take you longer than 10 minutes to do. Let me emphasize first that you should make sure you're prewired for the auto-dimming mirror before you go out and buy one unless you prefer to hardwire things, or return things.
Step 1: Check if you're prewired for the mirror. Start by pulling down the overhead console. Push on the sunglasses holder to drop it down, grab on with both hands, and pull down. Don't worry, you shouldn't break anything, but don't pull down insanely hard otherwise you may pull some wires out of the harness attached to it. Now check near the drivers side sunvisor and see if theres a plug taped down, if there is, fantastic!
Step 2: (if you're not prewired for the mirror, you can stop here).Push that plug through the hole near the windshield to get that out of the way. You can now put the overhead console back on.
Step 3: Behind your stock rearview mirror, theres a little screw holding it on. You'll need either a hex key, or a torx screwdriver to remove it (although you can probably use a flathead to get it out if you want). DONT LOSE THAT SCREW. Once you unscrew it, pull up on the mirror to get it to slide out of the little metal mount its sitting on.
Step 4: Now that the old mirror is out, get the new mirror. Get the plug you pushed out of the overhead console and plug it into the mirror. Now, slide the mirror back onto that metal mount and then screw it in.
Step 5: Turn your key on, or to acc, and the mirror should now turn on. Easiest way to tell is if the compass comes up.
Step 5.5: Admire your hard work and your fancy new mirror!
2007 F250SD, R/H power mirror with LED lights no work. All other lights and L/H mirror work fine. Checked the fuse in passenger compartment, it's good. Where to start looking?
View 5 RepliesI have a 2012 Prius with Advanced Technology Package. I'd like to always have Lane Keep Assist on. Is there some sort of hidden setting so this comes on by default rather than having to set it every time I start the car?
Also, I don't like the dim feature of the rearview mirror. It comes on by default. Is there a way that it can be set so it is off by default? It is hard enough to see out the rearview sometimes, and the dimmer makes it more difficult for me at night. I don't like having to hit the switch every time I start the car at night.
Do the passenger rearview mirror tilts down when you put the car in reverse?
View 7 RepliesCouldn't make it 10,000 miles........without a failure.
My driver's side mirror finally broke. It will no longer power fold. It's been slowly dying over the last few weeks, getting slower and slower. Now it won't move on it's own and the electric motor hardly makes any noise/effort trying to move the mirror.
I would assume that should be replaced under warranty but who knows... We'll see what service says about it tomorrow.
I've got an 02 Santa Fe with the auto-dimming mirror. The tension that keeps the mirror in position has gotten loose, so the vibration from the road causes it to slowly move downward while driving.
Is there a way to tighten this up? Do I need to remove the mirror from the windshield to do this? (because, I can't even seem to figure out how to do that!)
Hearing a whistle noise after installing the Recon smoked turn signal lense? The whistle starts between 40 and 50 mph and is the driver side only. I have triple checked the installation and it has the same clearance all the way around as the left side. I sent Recon an email on Jan 5th about this issue and still haven't heard back from them.
View 14 RepliesMy folding mirror on the drivers side folds out good but when bringing it back there is a clicking sound and it doesn't move, a slight pull on it and it comes back ok. 2011 F350 SD.
View 7 RepliesHaving issues with their mirrors folding in? One of mine makes a popping sound and will not fold in or out. I can hear the motor running, sounds like a gear is out of alignment. Have tried to reposition manually with no luck. Is there a rebuild kit for the internals or will I need the entire mirror assembly?
View 14 RepliesI Probably don't have the right forum but I have searched without luck throughout the site looking to see if any one has swapped out their regular towing mirrors for a set of powerscope ones with power fold and telescopic functions. I also need to know if the wiring is going to already be in there for them , I know that the switch will also have to be replaced ,but is there any thing else? truck is 2013 f250 and this forum seems to have the most responses for that year and model.
View 7 RepliesHave a 2004 f250 that is having issues. Once the truck is started the idle goes from normal to loud almost sounds like its going to stall. A few weeks back the same happened when i was on a red light. It choked almost to where it was going to die. I accelerated when light turned green and would not move at all. I had to literally use full throttle to get out the road at about 5 mph. I pulled in to a gas station and fueled up as i had a quarter of diesel left and it stopped the rough idle and power starvation once i started the truck up again. It sees like this time its getting more persistent... FML AND THESE 6.0 problems
View 9 RepliesI recently bought a 2004 6.0 extended cab truck. It has 223,000 miles on it and has been running great. Bought it here in Arkansas where I live and recently drove it to Texas and back after having just put some Hot Shot oil treatment cleaner in it. I ran it the 1000 miles as it suggests. Just the other day as it was hitting the 1000 mile mark the truck started to lunge/runaway and stalled. I finally got it back home and started looking into the issue. Based on what it was doing, (lunging/running away, and at idle in park random burst of rpms and then dying after doing it a few times), I started to do some research. Most of the answers I found claimed it was the IPR valve. I found that the IPR valve is supposed to, as claimed by some, be pulled and inspected every 100,000 miles are so and if need be replaced or the rebuild kit gotten for it. So I decided to just replace it as well as the oil, oil filter and fuel filters.
When replacing the IPR valve I noticed that it was original and that its screen was missing. I didn't have any problem moving the little piston in the center of the shaft with a small bolt however that doesn't really mean that it isn't bad. I tried a magnet to see if the screen was still in there and nothing came out. I did not try using a camera as I do not currently have one, to look inside the port to see if I saw it. After replacing the IPR valve with a brand new one and changing the oil I started the truck. It seemed to be running a little ruff so I let it warm up. Not one minute later the exact same thing started happening, lunging/running away (random increase and decrease in rpms), so I called it a night. The next morning I decided to change the fuel filters. No that it matters the order in which I did it, but I changed the top end filter first and the the one on the frame with the dealer recommended OEM filters as was the case with the oil. I did find in the filter on the frame that there was a small amount of sand and clay soil looking matter in the filter. I did clean out the filter housing as well.
After replacing the filters I started the truck to warm it up. I noticed that it was still running a little ruff but no random, lunging/running away (random increase and decrease in rpms). However after five minutes it started coming back. I finished letting the truck warm up and took it for a drive. Got it up to between 7-80mph for about 15 miles to try and see if I could "blow out" whatever may be in the fuel if that was even an issue I do not know. The truck seemed to get more power and run a little more smoothly so I stopped at my buddies house not to far from where I was and let it idle. No issues other than a little ruff idle. After about 10min I took off towards home doing similar speeds. I noticed at a little over 2000rpms that the truck was shaking a little but so I dropped the speed down. When I got home not more than one min after idling the same issue, lunging/running away (random increase and decrease in rpms), started happening again.
At this point I took back to the interwebs and came across a post that said the ICP might be bad and does cause this issue, lunging/running away (random increase and decrease in rpms). However I also noticed that this is a huge debate as to whether or not the ICP can cause this. Ford master mechanics say no and other mechanics say yes and round and round it goes. I decided to do the simple test many recommended which was to simply unplug the ICP and see if anything changes. Things did change. No more lunging/running away (random increase and decrease in rpms). Not more than two minutes after plugging it back in, allowing the computer to account for it now, the lunging/running away (random increase and decrease in rpms) came back. In the middle of it doing this I unplugged it and that went away. So needless to say I replaced the ICP and voila the lunging/running away (random increase and decrease in rpms) is gone but the ruff idle is still there along with a slight loss of power.
To answer some questions:
1. The oil and water are not mixing so I am almost positive that the heads are fine
2. The intercooler couplings are leaking a bit. I have ordered the new ones and will replace them as soon as they come in. Can this cause the issue?
3. I am blowing no white or black smoke except for when the lunging/running away (random increase and decrease in rpms) issue was present and the truck almost died. It would knock occasionally when it almost died and would send a slight puff of black smoke which I assume is a low or high fuel issue from the truck trying to die
4. I have not had the no start issue at all
5. I did not see any debris in the oil during the oil change
6. I didn't do the air test on the ICP port as I do not have the adapter.
7. The only code I got on the IBD II port was when I unplugged the ICP which was to be expected
8. I found no damaged wires
I am at the point where I am wanting to take it to ford to have them run a diagnostic on it but am wondering if there is anything else I need to be looking for. Here are a few questions I have.
1. Does this sound like a bad injector? (When I bought the truck it would sound like a misfire or ruff idle condition was present for about 5-15 seconds and then it would smooth out with no issues. It would run a little ruff if you tried to take off without letting it warm up, which I did once or twice and low rpms, but when it warmed up no issues were present).
2. Could this be the HPOP?
3. Could this be the FCIM? (The previous owner had replaced the FCIM not to long ago with one from Ford I believe. Said it cost him something like $700)
4. Could this be something clogging the oil screen under the manifold?
My final question right now is do any of you know where or what brand OBD II reader or software I can get for a decent price that will tell me the voltage of each injector and FCIM is without me having to go to Ford to get it looked at.
My truck died on the way home the other night. After pulling over it started right up but died three more times on the way home. Changed fuel filters, cps sensor which wasn't bad when tested, checked fuel pressure (60 psi), cleaned egr valve, fcim has 48 volts, batteries have 12 volts. Tried unplugging egr valve and icp sensor. Truck will start with icp unplugged . Ipr, stand pipes and dummy plugs were replaced last year when I purchased truck. Truck will run in park fine no issues idled normal, builds rpms and boost. Put it in drive when it gets warm rough idle and dies but starts right back up evertime. When truck doesn't die it has no power.
View 10 RepliesI have a 2005 F-350 Lariat, FX4, CrewCab, with an 8ft Bed if any of that matters. Currently sitting at 191,000 miles and 4,500 Engine Hours I just started running into some issues that I cannot figure out. To start with here is a list of all the mods and prior maintenance that I've done to my truck over that last 6+ years that I've owned it.
I purchased the truck in 2010 and had no issues whatsoever for the first 3 years.....then it all started. While pulling a camper home from vacation "still bone stock" the truck overheated and by the time I realized it it was to late. I ended up blowing a head gasket cracking a head and blowing a hole in my coolant reservoir from the heat & compression of the engine in the coolant system. So to the shop it went.
All of this was done at the same time at just under 4,000 engine hours:
1) Both heads were sent out to be pressure tested "which is where the crack was found", so 1 replacement head and the other trued up and tested by the machine shop
2) All 8 injectors replaced with Airtex/Wells New/Reman
3) ARP Head Studs
4) BPD EGR Cooler
5) New Stock Coolant Reservoir
6) New Stock Oil Cooler
7) Motorcraft Coolant & Oil/Oil Filter Change
8) New Serpentine Belt
After getting the truck back I installed some upgrades that I had wanted but didn't want to do until I had head studs. 4" Turbo back Diamond Eye Performance exhaust, Bully Dog GT Tuner with an EGT Pyro, coolant changed to Caterpillar ELC, Sinister Diesel coolant filtration system, new Optima batteries "I hated them",
Forward a year with no problems I had a crank but no start. I ended up having a bad IPR. A buddy rebuilt the turbo since I had it out and it was leaking. He apparently did something wrong because it took its own life sometime after. So a brand new stock Garrett Turbo with a Wicked Wheel 2 & I changed the IPR "don't remember the brand." Also replaced the factory paper air filter with a cleanable one from AFE that fits in the factory cold air intake.
Little more time and I started to have some overheating issues again, luckily the Bully Dog was monitoring and I had alerts set up so I caught it way before it caused any serious damage. Turned out the fan clutch wasn't working. So I replaced the Water Pump with one from dieselsite.com that has a steel impeller, also replaced the computer controlled fan clutch with a 7.3L mechanical fan clutch and an adapter from BPD.
After that the batteries I hated were replaced. I installed Oddssey Extreme 950CCA ones, a new 185A alternator from FICMRepair.com as well as the complete battery wiring interconnect kit. Did the blue spring upgrade. Replaced my FICM with the BPD 6 phase at 54V setting. Also I changed my starter to an 6.4L Ultima one from O'Reily Auto to bring me up from that slow crank of the 6.0L at about 150RPM to the 225RPM of the 6.4L.
So now on to the current issue. This has happened in the last month and may be related to the issue. I had some small coolant leaks and wanted them fixed. Pressure tested the system & found the radiator and timing cover gasket leaking. I installed a new stock radiator and lower radiator hose. Had the shop do the gasket and a serpentine belt due to cleaners being all over it. During replacement of the timing cover gasket my mechanic found that the LPOP gears had some damage as if something had be in there at one time. Not sever damage just minor. LPOP replaced with brand new one from Ford.
After I got the truck back it was fine for 2 weeks, no leaks or any problems whatsoever. Then I noticed a hesitation as I was leaving work at idle. You could see the RPM's moving up and down by about 50 as it sat there at idle. It got really bad and eventually stalled on me. It fired right back up and ran fine after. I was thinking water in the fuel or just maybe old fuel because it was kinda old and I was at 1/4 of a tank. I went and filled up and it ran great all the way home. Day or so later same thing. At idle you can see the RPM fluctuating and while driving it feels like it has no power at times then it goes away and runs fine. So I changed both fuel filter with Motorcraft ones and put in a new oil filter. It is the Wix brand but I've be running it for years with no issues, one was also in it way before this issues started. The oil has about 2,000 miles on it currently. I verified fuel pressure at idle to be at 70PSI. I tried unplugging the ICP at idle with no change in the hesitation. So I plugged in my SG2 and started to see if I could see anything out of the ordinary.
OAT - 60 Degrees F
KOEO Engine Cold - FMP - 54.5V, ICV - 0.25V, ICP - 0, IPR - 14.9
KOER Engine Warm - FMP - 54.5V, ICV - 0.82V, ICP - 576, IPR - 23.5
Cruise at 40MPH - FMP - 54.5V, ICV - 1.14V, ICP - 965, IPR - 32.9
Cruise at 50MPH - FMP - 54.5V, ICV - 1.42V, ICP - 1,190, IPR - 38.0
Cruise at 60MPH - FMP - 54.5V, ICV - 1.27V, ICP - 1,143, IPR - 37.2
While driving this issue comes and goes very randomly. The only parameter I notice changing alot is the IPR. It jumps around a lot and sometimes it will go to 85. I know that this isn't a good thing so I am going to change the IPR later today or tomorrow. I already had a brand new Motorcraft one to put in, plus at the very least I want to look at the screen. I had read somewhere that there could be air in the oil system and that if you run at a high RPM it can remove this air. I never seen any bubbles or anything on the dipstick. My brother ran the truck for me at 3,000RPM for 5 minutes. No hesitation during the test but he didn't have the SG2 plugged in so I don't know the parameters during the test. I thought that it worked but then it came back after a few miles of driving. The above parameters are from this mornings drive home from work.
I was driving my 2011 the other day home from work and experienced a rough idle. Normally the truck idles pretty smooth. I noticed when I was driving at highway speeds the truck seems to shake a lot. I pulled over and turned the truck off. I did a walk around and could find anything out of the ordinary. I started it back up and no more rough idle. However while i was driving at freeway speeds I could feel a momentary lack of power, then the truck would regain its speed. This would only last a sec or two.
I figured I'd give it a few days.... well now its gotten worse. Its doing the same thing but a noticeable difference in the lack of power. I still have boost pressure and the turbo seems to working fine. Im trying to figure out what it might be. I'll be taking my truck into ford again...
05 6.0 deleted and studded. 170k fresh filters and oil, no CEL or codes.
This has happened 3x in months, so it intermittent. Truck will start fine cold, except for this last episode ....
Truck starts right up, idles correctly, speed bumps up if its cold enough to trigger the high idle. About mid way through its warm up, at approx 130-140 idle falls off, barely runs. Almost knocking. Black smoke if you give it throttle. Has no power when its doing this. Truck will not move and almost dies in gear. Give it til 185ish degrees then pooof! All good.
However 2 days ago it wouldn't start. Cranks but won't catch. Stumbles and dies. Finally got it to start after setting the charger on it. I killed it. But this time when it started it was straight into its rough idle, no power...until about 180. I switched it off, restarted it and it was totally fine
Ficm is 47-47.5. Every now and then I see a 46.5 for a split sec
Hpop is 700-800cold cranking.
Not sure what else to look at.
Moto craft filters.
Amsoil 5w-40
Archoil in the fuel and oil
Twc3 at every fill up.
Having some problems with an e-350 dying when in gear and rough idle. Truck starts up after it dies. Vehicle acts like it is starving for fuel. I have check fuel pressure after fuel pump and getting 55psi. High oil pressure pump with in normal ranges. Cleaned and checked egr and it was in the closed position. Fuel filters have been changed. Injector buzz test ok.
View 14 RepliesThis morning I noticed when I started the truck had a rough idle shaking truck. The truck felt weak. Boost would go up but truck felt like it was in sand. While coasting on the highway at 50-55mph the truck not only lags in power but vibrates viciously until the overdrive kicks in that vibrations in cab and ssteering wheel go away.. What might be going on?
View 6 Replies