What the normal tire pressures are so the TPS will not alarm? The sticker on the door says 65 front and 80 rear for my F-350, but I think this is a bit high when empty or not pulling trailers, etc. Additionally, is there anyway to adjust the TPS settings?
View 10 RepliesI just had my turbo and the EBPV on the pedestal rebuilt. Now I need to put it back into the truck. What is the procedure, if any, to adjust the EBPV? I only use the truck to haul a 5th wheel RV and the performance chip closes the EBP valve when going down steep hills -( EXHAUST BRAKE)
View 6 RepliesWhat's better good options on a upgraded HPOP? As of now I have a stocker, it's getting low on pressure when even on my 50hp setting.... Was looking at T500 and Adrenaline. Any others could recommend? I'll be doing injectors down the road here too.
View 14 Repliesis there anyway to adjust the brightness of the lcd info and nav displays. I know the light dimmer adjusts it but not in relation to the gauges, if I turn the screens down enough I can barely read the speedometer. is there a way to adjust just the screens?
View 3 RepliesI am installing Torque Pro and Car Gauge Pro on my Yellow Submarine. To keep an eye on things. Well installing it on my tablet, and installing that in my Yellow Sub. I already have the Bluetooth dongle. What to set up, what to monitor, what to test? Etc..... I want to continuously monitor this truck while driving it. Being it went swimming.
View 13 RepliesI'm looking to buy a used 2005-2007 6.0L and bought a ScanGauge to take with me when I look at the next truck I'll be considering. I dont have a truck now and I see that the ScanGauge derives power from OBD port of the truck. Is there any other way to set it up in advance?
View 9 RepliesLong crank to start hot and cold. Acts like missing when its cold tho and when it warms up it runs ok but it will set code weafher warm or cold and u can turn it out with scan tool and drive and it wont come back till restarted again...
View 1 RepliesI had new nitto snows put on my truck and low tire pressure light is on.....Checked tire pressure 65 front and 80 back.....Started truck and screen said tms pressure low.....Hit ok and drove around on and off for 2 days now and cant get the light to go out......Is there some way to get the light out or do I have to go to my dealer to have it reset???
View 14 RepliesLast week I was driving on the highway and noticed the oil pressure gauge showed no pressure. Limped a half mile to the mother-in-laws and called for a tow. As my truck was pulled onto the flatbed I could see oil all over the bottom of the engine, tranny, rear end, etc. Turned out to be a bad oil pressure sender, which was leaking enough oil to blow the plug off the top of it.
I replaced the sensor, cleaned the engine and under-carriage, checked oil level (which showed no loss of oil) and drove around for a week without an oil pressure gauge while I waited for a new pigtail. Put the pigtail in yesterday and drove it today for the first time since. Gauge was working, got to the bank and it was reading zero pressure again. Limped home and watched the gauge go back up quickly and then back down. This happened twice and was showing pressure when I shut it off. Checked under hood, no oil leaks and plug is still secure.
My truck gave me low fuel pressure and reduced pressure limp mode at 21,000 miles. The fuel and air filters were changed at 16,000. The dealer said all they found was the fuel filters (at 21,000) were what needed to be changed. Also, why does my truck hum??
View 14 RepliesMy truck is all stock and I am running in performance tune? And my friend the former owner said I need to let her loose about 75 percent of the time I am driving it because it's my DD and I do not tow anything on a regular basis. I do not want to stretch my bolts by unnecessary pushing, I don't know if I'm even pushing it hard but I normally get the turbo up to about 30 psi is that to much?
View 8 RepliesI have an early 04, I'm not sure if there's a different in pressure over the years. But I'm curious what normal or average readings are. Btw I did replace the icp and pig tail last year. Here is what I have in psi from my sct
Cold start at idle 680 .23v
Warm idle 635 .24v
Cruising 1800rpms about 1500 .32v
WOT about 4200 .78v
I wasn't sure if I should be having any sway at all while pulling our new 30' TT. Dry wieght is 7200lbs, GVW is right at 9500lbs, tongue weight is around 800lbs, and I'm running a Fastway E2 WDH with sway control built in. While towing this weekend, I was experiencing a very slight amount of sway. It wasn't what I considered to be much of an issue but my wife and daughter both asked why the truck felt as if it was moving side to side slightly. When I say slightly, imagine a small glass of water filled about 1/4" from the top. The sway wouldn't have been enough to spill the water, but enough to sway it slightly back and forth. Winds were about 3-8mph hitting me from the north west (in relations to my trucks heading).
I do have some suspension enhancements that might have contributed to the sway. I have roughly increased the rear end by 4" by adding add-a-leafs and F350 blocks. I have Fox 2.0 shocks and a Helwig Bigwig sway bar. Plus I'm running 295 Nitto Trail grapplers , all 4 at 80psi. I've read that the more aggressive tires could also be a contributor.
My question ultimately is: should I be feeling any sway at all? Is a very slight amount of sway normal when pulling a 30' 9500lb rear hitch pull?
It takes about 10 minutes for the truck to drive normal. If I start the truck and sit for 5 minutes, then start driving... the truck has a very hard time changing gears and accelerating. Just trying to see if this is normal or not ?
View 14 RepliesDecided to try and swap in LED bulbs into the sub par factory headlights and since some engineer somewhere decided it would be easier for me to have to remove the grill and headlights just to change a bulb, I noticed that the dual horn set up had the horns pointing back to the truck. Even worse, right in front of all the fins on the CAC, Raidator, etc. to reduce muffle the sound.
Now I don't know how things are where you live, but generally when I honk at someone, I'm not doing it so I can hear my own horn. The general idea I thought was so that others could hear my horn.
Of course the same engineers in charge of headlight bulb swaps also figured out the wiring for the horns so you can't just loosen the nuts (10 mm) and rotate said horns 180 degrees. You can rotate the driver side horn 180 degrees and call it good, but the factory wiring won't reach the passenger side horn if you rotate it.
You can however remove both horns and use a small screwdriver to unplug the harness that joins the two horns. If you swap the horns right to left and left to right, then you can put the factory wiring back together in a manner that leaves the horn outlets pointing forward towards others.
I can't insert pics into the thread as I describe things. I used to do that but FTE seems to have gotten rid of my gallery so I can't upload to there anymore and then post photos in the thread that way. So now you get them uploaded as attachments at the end of my rambling.
I currently have a 2003 F-250 6.0 with 112,000 miles on it. While traveling interstate speeds (70+) and the I can hear the cooling fan rev up and down every 10-15 seconds. Is this normal?
Also when it spins up, it sounds normal then make a high pitched squealing noise. Thoughts?
I am also needing to rebuild the fuel bowl. I noticed DieselOrings offers rebuilds for the 7.3 but not the 6.0. Will these fit or any suggestions on parts?
I'm having a bit of a cold start issue, need to know if it is normal or something is wrong. I live in southern Indiana and it's gotten down to a VERY cold 50 degrees (lol) and the past two mornings I have started it up and it seems to have a misfire first thing in the morning and it will kick into high-idle mode and after I shut it off and start it back up about 20 seconds later after the ECT gets above 100* and it runs perfectly. It has brand new 190/100 injectors from Warren, an IDP tune, and I am running 13 quarts of FoMoCo 15w-40 oil with 2 quarts of hot shot stiction eliminator (tried it before installing new injectors). And also throwing no codes. Is this normal or should I be looking for a problem?
View 13 RepliesI have a 12 cc 4x4 drw. I hauled a bull and a cow about 100 miles this morning. I was pullling approx 6k including the trailer. The temp was about 75*. 50-60 miles into the trip I switched to the oil temp screen and the oil temp was 224* and the trannie was 199*. I was going into the wind which was about 20 mph, and I was traveling 75mph. The truck never lugged down heck it never shifted out of 6th gear. When I unloaded the cattle the temp came back down around 190*. Headed home and the temp got up to 226* and the tranni went to 205*. This was going with the wind and just the trailer. I am using oem 10w-30 motorcraft and motorcraft filters. The truck just has 9k miles on it. I am thinking that the oil temp is a little warm, should I be worried. What should I look for to diagnose. I like to do my own diagnosing if I can, the dealers around me can't find anything wrong even if you point the leak out to them. Should I be using a different oil?
View 14 RepliesI know it seems like everyone's truck tends to have different tolerances when it comes to when it starts and stops regen when it comes to gpl but the last two times my truck has gone into regen it starts at 100% and finishes at 25%. Is it normal to stop regen when it gets to 25% or should it be stopping at 0%. Or could it be that the percentage in my truck is off and it's actually using the gpl to start and Stop? The only thing about that is that forscan says it's supposed to start at 100% which it does so if my percentage is off that would mean it was starting at 75% does it not?
View 14 RepliesTook a trip today that was 3 hours there and 3 hours back. Truck ran normal on the way there (eot about 202 and ect about 196-198), but on the way back truck ran a little hotter than normal (ect as high as 214 eot stayed within 2-3* plus or minus ect). Fan did kick on every time I hit ect of 212 and would drop it down to 196-198 and oil temp would drop at the same rate.
Truck is stock 190k miles with a bulletproof egr cooler and coolant filter. Oil cooler probably has about 20k on it. (4th one on this truck- since I like changing them out as much as the rest of us). I checked coolant level when I got home and I might've added a pint to get to bottom of sticker. I'm not sure it wasn't a pint low when I did last flush and cooler replacement.
No puking and I can't find any leaks. I pulled egr valve and no moisture in manifold just a worm out o ring that'll I'll replace. I can't find any leaks. Where to check that I haven't? I don't feel like I'm losing coolant because I wasn't really low. My fan never failed to kick on when I hit 212 or stopped at a red light. No moisture in manifold so I'm not thinking losing coolant due to head gasket. Maybe radiator looks ok but tomorrow I will blow out any bugs to make sure.
I've done a ton of searches and everyone talks about the 250 rear blocks being 2 inches. I got under my truck the other night and my factory blocks measured to just shy of 4 inches. It seems like everyone says that those blocks only come with the 350s...
is there some sort of package that I might have to come factory with the larger rear blocks?