Ford 6.7L Power Stroke Diesel :: Key Fob Work In Very Limited Distance?
Nov 6, 2013
So I bought my truck about three months ago. The first day I got it I obviously wasn't paying so much attention to the key, that I didn't notice that my keyfob wouldn't work at all or had limited distance. Anyways, I go to the dealership and the keyfob(Normal one, NO Remote Start) works perfect for them every time. I have been so frustrated with this for a couple of weeks now, I decided to take it into my own hands and take it apart and see whats going in there.
On the top right side of the key, there is a gap between the two plastic pieces that you can fit a flathead in and turn to open up the actual key. In between those pieces is a rubber mat type thing, I assume to keep water out. After you take that off, you will see the battery. On BOTH of my keys, there was this clear goo stuff, which again I will assume that it's some sort of contact/battery protector put on by the factory.
Well the text on the inside of the key says not to wipe the battery contacts, but I took a Cu-Tip and got all the clear stuff off the battery and contacts! I now have 100 yard distance with my key. It works EVERYTIME now.
View 14 Replies
Advertisement
It's my turn, while out site seeing my back seat power window don't work , the control from drivers seat or from the back seat door control, I popped both covers on the control switch and both are firmly plugged in, I don't have my meter with me to see if power is running back to the switch , this morning I'll try to switch out the two back seat controls to see if I can get at least that window to go down , 04 350 , would there be a fuse for each or is it in the switch in the door that the harness plugs into , that's the only window that won't go down...
View 8 Replies
2007 F250SD, R/H power mirror with LED lights no work. All other lights and L/H mirror work fine. Checked the fuse in passenger compartment, it's good. Where to start looking?
View 5 Replies
I can't get the damn auto unlock to work. I've enabled it and disabled it and nothing still reset it all and all that just got the truck....
View 7 Replies
What is the throw distance of the actuator arm for the wastegate on a stock 2002 7.3L Excursion turbo?
Or how far the wastegate needs to move?
I'm thinking about using a 12v linear actuator to control it so I can trigger it from my gauge alarms for high boost, high EGT, low Fuel pressure, anything really
View 8 Replies
My mechanic put a used 2005 PMC in my 2004 powerstroke. Now tachometer does not work, trans and coolant temp guages don't work and drives as if it is stuck in 3rd. gear. Does it need flashed @ a ford dealer to sync the two together?
View 14 Replies
I have a 15 F350 DRW 6.7 pulling a 19K fiver with 8K axles and disc brakes, I have to have my brake controller set at 10 to get the brakes to work well. The pads are good, just bled the system using a power bleeder, controller is set to electric over hydraulic with max gain. Why I need to have the controller set to max?
View 14 Replies
I noticed my A/C hasn't been up to par. It's not bad when driving but just ok when idling. So today I changed the orfice tube and the accumulator. Vacuumed the sys. down and charged it up, 2 lbs 10 oz. It is worse! the compressor kicks on and off constantly only cooling to 80 degrees.
I noticed the high goes right up to 350 then the compressor shuts off .... 7 seconds later, back on and up to 350lbs and off again. I think the high-pressure switch is shutting the compressor off before anything goes kaboom but why isn't my fan cooling the condenser down? my FSS shows no increase in fan speed. Sitting at 450.
I think I'm going to cool the condenser down with a hose now to see if that works. If so, That would be telling me the fan isn't doing it's job correct?
View 5 Replies
I have a 2015 Ford F-450 6.7L Diesel with a 12 foot flatbed on it that I use for my power washing business. The air conditioner sometimes won't work when I first drive it in the morning. After I make a few stops and turn the engine on/off a few times it will all of the sudden start working again.
This happens about 2 or 3 times a month and I don't have time to have it sit at Ford so they can duplicate the problem. It's going in for it's 60,000 mile service in the morning anyways so I'll still have the dealer look at it. What might be causing this?
2015 Ford F-450 6.7L Diesel 12 Foot Flatbed
View 14 Replies
I recently did the high idle mod but as many of you know it does not work with remote start. I found the below link on how to make it work with rewiring how the aux switches receive power. Are the aux switches hot all the time even with the key off?
[URL] ....
View 5 Replies
No matter what I do with the settings for my heater in my lariat air only blows out of the dash vents. Defrost and floor vents don't work it still blows hot air out of the dash vents. I'm not sure what the deal is maybe the vacuum system? I did a search and all I could find was people having trouble with air ONLY blowing out of the defroster and my case is just the opposite.
View 8 Replies
I have the later model 2004 F250 6.0 (built May 2004). I have owned it since new. It has 157K miles.
My newest problem comes after I did oil cooler work. I know everyone points to the IPR and/or ICP, but my readings seem strange to me.
About three weeks ago I replaced the oil cooler with a Bulletproof remote unit that uses the factory oil cooler. During the job I removed and installed a new Ford IPR sensor and added the improved screen to it. I removed and installed new Ford water/oil temp sensors, a Ford low oil pressure sensor, and a Ford ICP sensor (in the pax valve cover). I also installed the improved turbo feed line and turbo drain tube. I rebuilt the oil filter/fuel housing and installed new o-rings and the blue spring. I have the dual alternator set-up and had been running the lower alternator unplugged for the last several years. (I know I know). So I swapped in a reman alternator.
I managed start-up after running batteries dead a few times. During the drive I felt idle speed jump up by itself a few times while at low RPM. I felt an unusual skip or two in the motor but the power seemed ok. I accelerated and the truck pulled fine. At highway speed I heard what sounded like the engine hitting a high rev and trying to cut out, but it was very mild. I noticed this first at 2000rpm, but it may have not been pronounced enough for me to notice it at lower RPM. When the cut-out occurred strongest I slammed the throttle down to see if the problem would worsen, but the truck accelerated well with no cut-out, but when I eased off the throttle at higher RPM the cutting out returned. My Banks IQ showed P2284.
I installed 2 new batteries and replaced the ICP pigtail and soldiered it. That had no effect. I put the old ICP sensor back in. That had no effect. I borrowed a Snap-on Solus Edge scanner to test the truck. I would add that the truck starts up as quick as it has always started; 3-5 seconds.
Scanner results:
Key-on, engine off, ICP (voltage) reads .25, IPR reads 15.
During the crank sequence (before engine start), on a freeze frame, RPM is 157, ICP(voltage) reads 1.04, IPR reads 21, ICP pressure reads 768.8 psi. That seemed kinda normal.
Engine running at idle RPM, I read ICP (voltage) 1.2, IPR 15, ICP pressure 863.1psi. That seemed okay.
I drove the truck with a cleared code and noted that something occurred to change my readings. Before the change while driving under a short heavy acceleration to 54mph, I noted these readings: 3533rpm, ICP (voltage) 3.77, IPR 60, ICP pressure 3400.1. I eased off the throttle, stopped the truck, and noted an uncommanded REV-up by a few hundred RPM and back to idle. It was a quick burp. Afterwards ICP pressure and IPR readings went strange and the code 2284 came up. Looking at the graphs over time, RPM, ICP pressure, ICP voltage, and IPR all follow a similar curve---until the REV-up occurred.
The scanner next showed that as I mildly accelerated to 1705 RPM (about 15mph) graphs showed ICP voltage, ICP pressure, and IPR went up. But when I let off the throttle ICP pressure became fixed at 869.9. I continued to drive the truck.
The truck accelerated fine as it had under previous runs. The Scanner shows that although ICP pressure remains fixed, the ICP voltage climbs and falls with RPM. With RPM ranging from 630 to 1800, IPR holds at about 30. Then under a very heavy acceleration to 44mph, ICP pressure began to increase above 869.9, then followed ICP voltage upwards. ICP pressure climbed to 3479psi with an ICP voltage of 4.64. At that moment IPR read 69%. That seemed normal until I let off the throttle. Then ICP pressure drops back to exactly 869.9 which I assume is some sort of PCM-induced value.
It is during this time at higher RPMs I can hear the engine-cut-outs, but they are mild and the engine still responds to heavy acceleration. I have accelerated full throttle to 100mph and saw max boost values of 29psi (stock program). On engine shut-down and restart the problem seems to reset itself and the truck will run normally for a bit before the failure occurs.
To correct the problem I have removed the banks equipment. There was no change. I have ordered the ICP short connector that will allow me to test actual voltage on the ICP while the engine is running. I plan to soldier some wires and run the meter into the cab for testing.
The scanner reads a desired ICP pressure as well as the actual ICP pressure. When the failure occurs both the desired and actual read 869.9 at less than heavy acceleration.
The scanner also reads desired RPM as well as actual RPM. Desired RPM remains pegged at 640rpm all the time.
Also, engine running the FICM voltage in is 13.5 and voltage out was 47.5.
On the very last test run I got two new codes: P2138 and P2140. I had run the truck with my foot on the floor on that test. Is this a glitch or does this play into my problem?
View 14 Replies
So, I've been having cold start issues for a couple of years now especially when temps get below 25 or so. It started with virtually no issues until temps got into the 20's but got to the point this year where it run a little rough at startup even in the summer. Once ECT gets up around 140* it runs pretty good.
I took it to a diesel shop last year and was told I had 1 bad injector and a bad glow plug. I couldn't afford to do the work, so I waited.
Now after researching this site, I'm more inclined to think it may just be the FICM. I've seen scangauge numbers in the low 20's up to 48.5. On cold morning FCM will usually start in the low 30's and gradually work up to upper 40's. The batteries were both replaced 2 years ago, but I probably should give them a load test. The alternator voltages vary from 11.0 to 12.5 when cold and 12.5 to 14 once warmed up. I have noticed that the AC blower will slow down a little when I sit at a red light, and then pick up again when taking off. I don't notice it with headlights or anything else.
According to Bismarc's spreadsheet, alternator numbers seem to be in the acceptable range, but I don't want to get a new FICM and fry it with a bad alternator. I can get the alternator or the FICM now, but if I need to do both at once I'll need to wait a bit longer.
View 14 Replies
2011 F-350 6.7L. Three years old. 60,000 miles. The lights and radio work, but she won't turn over. Tried a jump start from a car with no response from truck. Wrecker coming.
View 14 Replies
Bought this truck, and the engine coolant temp gauge does not work, so I replaced the sender, still don't work.
View 8 Replies
What the problem is with my F-350 6.0. I have an intermittent problem with my Speedo reading zero while I'm doing 70mph on the fwy. since the speedo won't work the truck goes into limp mode, the turbo will not function at optimum level. I have replaced the diff. sensor, the trani sensor, the a.b.s.sensors, the instrument cluster to a reman cluster. Then when I had a local mechanic plug a laptop dianostic program on it as he was running through the system inadvertently the radio cut out, so I found that who ever installed the after market stereo they cut a few wires to the harness, I went to the junk yard found the harness end and replaced the end. so with all that said and done no one knows what is causing this speedo not to work and limp mode. about 4 years ago the oil pump stopped working and ruined the turbo so the whole front end of that glorious 6.0 was rebuilt the problem started about a year after that.
View 2 Replies
I have a 2013 6.7l super duty Lariat. I want to install flashing LED lights to work in conjunction with the hazard lights. The leds have their own controller and will be separate from any other lights/wiring. What I need is some way to trigger a relay to turn on the led's. Was hoping to tap into the hot lead off the hazard switch itself but that's not an option!
View 2 Replies
I have a 2001 JGC Limited with the 4.7 v8 quadra drive 4x4. Since it got cold out, my blower motor for heat will not come on until the vehicle has been running for a while. Sometimes as long as 30 minutes. Eventually it does come on and seems to work OK. It works the same way if its on auto or on manual- high or low speed settings.
View 1 Replies
Started today. 2004 with 235k miles. Owned for last 10k miles. Engine was recently studded, has egr delete and ccv bypass. Runs and starts fine. New Ford oil cooler too. Checked for codes. None for misfires, perdel are reading 0.
If it sits, on start up clear exhaust, as it warms, more blue smoke. Smells like oil not diesel.
Researched before asking and found leaking turbo seals can cause this. So we pulled the intercooler tube in front of the engine going to the intake expecting to find oil residue. Nice and dry. Was this the correct one to look at?
When we got the truck we had the dealer do a relative compression test and was within limits, it did need 1 injector that we replaced. What would be the next logical place to look?
Couple more points:
- Just changed oil last week, checked today, it was slightly over full.
- Coolant is fresh and has not changed level since we got it.
- Pulled fuel filter to see if any oil, but it was nice and clean.
View 11 Replies
I filled up at the same fuel station I've filled up at for 6 months, never had a problem. I just bought a 6 liter and put some injector cleaner in on the last fill up. Ever since then, it's been running really rough and missing when cold, and even when it's warm if I really lay into it, it'll pop and sputter. The fuel in water lights been on since I bought it. I think I have a bad sensor, because it was running fine until I put that cleaner in. Since its been running rough I put in new fuel filters and drained the fuel water separator, which only had fuel in it. I don't really know what it could be, but I'm 99% sure it's an injector issue since it started only after I put fuel treatment in.
View 8 Replies
It only happens on a very Rare occasion.
When Cold, and when I start out as I open the throttle, it suddenly sounds like there is not a piece of quieting stuff on the engine. I mean its like I can hear right into the engine itself.
I back off, It goes away then I dont hear it again for another Month or two.
View 14 Replies
