Ford 6.7L Power Stroke Diesel :: Gauge Cluster Won't Working?
Jul 16, 2015
Do the gauge cluster out of one super Duty will work in another truck, just plug and play? I have a 2015 550 that the fuel gauge has quit, which is causing the truck to go into limp mode because it will not allow a regen on the DPF. This is a business truck and i need it to be rolling. There appears to be a national back order on gauge clusters from Ford. I have another truck in the fleet that I could do without so I was wondering if I could just swap the clusters would it work?
View 6 Replies
Advertisement
My 2005 is doing strange things. The fuel gauge is always incorrect. I have done the following:
1. Replaced fuel level sensor.
2. Inspected and tested wiring from the firewall to the tank.
There are no codes present and the fuel % listed in torque is always correct. The gauge sometimes reads 1/2 above full, nearly all of the time it's above the 3/4 tank mark. I have an android head unit that I am using to gauge fuel level right now. I believe the cluster is bad.
View 9 Replies
I have a 2013 F250 with 49.575 miles and Saturday the truck left me stranded. I was towing my small trailer and doing about 45 mph.....When just out of nowhere .....I got every possible warning come across my display and none of my instruments were working. That included speedo,tach,boost....even the radio and ac were effected in some way. So after a few miles I was able to pull over ....cut the truck off and it wouldn't start.... So I had Ford roadside service tow it to my home dealership.
View 13 Replies
2005 6.0L F250 Lariat. I picked up a couple weeks ago. The message center in the gauge cluster will only show my mileage (kilometres) and engine hours but nothing else.
Also the three buttons/controls to the right of the steering column don't do anything. I checked the wiring behind the dash and it's all plugged in... The other problem is the SRS light will flash on and off while driving.
View 2 Replies
So, went to drive the truck (2004 F250 6.0, 145000 mi) yesterday and the right half of my instrument cluster was not working (tach, trans temp and water temp), CEL and check gauges lights on. My scan gauges gives me readouts of all 3, so I know the computer knows the right values. Pulled all three fuses related to the cluster, all looked good. All gauges, including those not working, did full sweeps with key on after putting fuses back, so I know they function. Also, the glow plug light stays on way longer than normal.
View 2 Replies
My right side of my instrument cluster is not working. the Tachometer, Engine Temp and Trans Temp gauge are non responsive, and the CEL and Check gauge light is on. I have seen other posts with people that had the same problem but no solution to what fixed the problem. 2004 F250 Lariat.
View 4 Replies
I currently own a 2006 F550 4x4 pick-up. I just finished changing the oil and my oil pressure gauge is not working....
View 11 Replies
Working on a 2015 f-550 with a 6.7 power stroke. Damaged the wiring harness and fuel gauge not working now. Where could I find a wiring diagram? The low fuel is now causing it to not regen. We have continuity through the wires and they have been repaired but gauge still does not work. Currently now power to fuel gauge sender?
View 1 Replies
I am working on my dads 06 F350. He had four dash lights go out, so we changed out the bulbs and put the dash back together. When we hooked the batteries back up all the gauges reset except the the boost gauge. The needle went way past 0 and bounced for about 2 seconds then it just stayed below 0. We have tried to reset it by unhooking the batteries and turning the ign. switch on and off several times. Always go back past 0 and stays there. It does work it just doesn't read correctly. I am pretty sure that the needle did not get turned on the shaft? Is there a way to reset it?
View 3 Replies
I just bought a 00 f250 cc that originally came out of Canada so the speedo and mileage is all in kilometers. I have bought a use cluster that is in standard units to replace it with. I am just curious if all I have to do is replace the cluster or if there is other thing that need to be replace as well to make it work right.
View 12 Replies
My 06 instrument cluster has a few bulbs that are out. I have seen the video on how to remove and send off to be repaired but have not seen any thing on how to replace bulbs. Is this something that I can do myself? Is there "kit" to replace all the bulbs? Where can I get the bulbs? Here is a pic of my panel.....
View 14 Replies
Is there one fuse for the entire instrument cluster? Because today the entire instrument cluster went dead, even the digital odometer part. Hoping it is just a simple blown fuse...
View 14 Replies
I've been searching for instructions/procedure on how to remove the instrument cluster on my 2006 6.0 Superduty. My odometer has been showing the classic signs of a cold solder joint, cutting in and out constantly. It's been doing this for a couple of years, and I've taken it to the dealership, since it's still under warranty, however they were not able to find the problem since they were not able to witness the lighting go off and on. I figured I'd just do it myself and not even bother with the dealership if I don't have to. I've read the threads on how to fix the issue, however, everything I've found is for 2004 or older models. Are there any threads specific to the 2006? Or, is the instrument cluster on the 2006 the same as another year model? Maybe I can find this info. there.
View 9 Replies
Purchased 2011 3 weeks ago. Due to not paying attention, put gas in diesel. Had tank dropped and drained but after reassembly, fuel gauge inop. When turn ignition switch on, get normal sweep of all dash gauges but fuel gauge does not read. 2nd tech says sender okay, must be gauge. Dealer ssays if it sweeps, it isn't the gauge. 011 F250 6.7L.....
View 7 Replies
I am currently converting a 1999 E350 7.3 diesel bus into a camper to live in. The bus has already had a lot of weird custom work. Done by someone else and a lot of the interior torn out and extra insulation put in. There is an exposed electrical panel behind the drivers seat. It was a cheap buy, previously fleet maintained with only 120k.
I was hooking up a battery for accessories to a terminal labeled "Battery" that does run indeed directly to the + terminal of the battery in the engine compartment.
Unfortunately I mistakenly connected the accessory battery to a terminal labeled "ignition" that runs to behind the dash. When I tried starting the vehicle off the auxiliary battery for a test everything went out for 2 seconds, I heard a click from the engine compartment, and everything than came back on. This is when I realized my mistake.
It used to be the speedo only didn't work (which I assumed was the step motor), now after this mistake all the gauges, the odometer and the buzzers don't work. Lights like the battery and airbag warning indicator still function.
Checked fuse 2 (15 amp) for the instrument cluster and it is intact. Actually checked every fuse in the vehicle in both fuse panels and all are intact. The radio works though and the vehicle is not equipped with power windows.
Going to go get a radio removal tool to take apart the dash and get back there. What this could be? Did I fry a relay? Did I fry the cluster circuit board.
View 6 Replies
Got in my 06 F350 dually 2 weeks ago and after start up had no instrument indications. Truck ran great, flat line on panel. Tow haul light out also. Drove it for appx 5 miles, shazam all start working and then they cycled on and off for a while. After 10 miles, came on solid. Happened again at a later date.
Here's what I discovered. I noticed high voltage on my Scangage II. As in 16.2VDC. Monitored it coming back from a hunt. 14.9-15.5VDC. Would blank out only after hitting 16.2VDC. I'm suspecting there might be a cutout to protect the instrument cluster from damage.
Installed a new alternator on Friday the 13th. Drove home this weekend, 4 hours and no problems. Hopefully didn't boil off the batteries. Now 13.5-13.9VDC ... Just something to be aware of!!
View 2 Replies
My ScanGauge just went blank, which was nuisance because I like to monitor it in the mountain climbs. It felt like a 'naked' dash without it. My separate pyrometer was the only additional info I had. The ScanGauge only has a few thousand miles on it. Wondering how reliable these things are before considering getting another, or inquiring about a fix I know I will first have to double check that the OBII port is still OK, but I expect it is.
View 11 Replies
What is the least intrusive way to install an oil pressure gauge in these trucks and still maintain the input to the computer?
View 6 Replies
I am installing Torque Pro and Car Gauge Pro on my Yellow Submarine. To keep an eye on things. Well installing it on my tablet, and installing that in my Yellow Sub. I already have the Bluetooth dongle. What to set up, what to monitor, what to test? Etc..... I want to continuously monitor this truck while driving it. Being it went swimming.
View 13 Replies
Have 2006 Ford Power stroke with 6.0 in it.. Just started doing this ... When Im driving the oil pressure gauge is fine and motor sound fine, but sometime when I come to a stop sign the oil gauge will drop all the way down to zero, the motor still runs fine and has plenty of oil in it. After I press on the fuel pedal to raise the RPMS just a couple the gauge goes back up. the odometer will all so blank out and it will flash "read gauges" when this occurs,, its driving me crazy and not sure where to start..
View 14 Replies
I have googled for this and searched the typical sites but cannot find the PID to monitor the MAF with my scan gauge II. Am I blind or does it even exist?
View 1 Replies
