Just like our fleet of 06' F-150's, my emblem on my 2011 F250 is starting to peel and bubble up on the front grill. Every 06' had their rear and front emblems replaced close to 3 times until we just gave up and lived with it. I thought Ford fixed this problem? Going to the dealer tomorrow to get a warranty repair.
View 14 RepliesIs there an easy How To write up on how to remove the front grill? I want to install some grill inserts I picked up.
View 7 RepliesHow do you remove the front grill? I'm changing the bulbs in my headlights, and I know it's stupidly simple just can't remember how to do it.
View 1 RepliesI am having trouble finding the correct part number for the Ford emblem that goes on the front grill on an 09 F150 lariat crew cab. My father in law asked me to order one since his is faded badly. What is the correct part number?
View 1 RepliesHow to get the fender emblems off? I am talking about the F250 Lariat on the front fenders. I checked out the dealers schematics and it didn't work much.
View 2 RepliesMy tailgate emblem has lost the blue color. Is this a common problem? Is it easy to replace the emblem?
View 12 RepliesI just bought this grill [URL].... and it fits great. However, the grill does not come with a emblem so I was just going to put mine from my 06 Passat on but it is a lot smaller than the opening on the new one. Am I just missing something here, or are there different size grill emblems on some cars? Or is my new grill just messed up?
View 3 RepliesHow can i mount a F emblem i bought for my Grill?
View 8 RepliesI have a 2003 Ford F-350 super duty 6.0. A few weeks ago it starting loosing power, it wouldn't even go up to 15 mph. It now won't even move. There is 0 power. When I press the gas the motor bogs down to a very low idle and wants to die. I also had recent trouble with it starting. It would wind up to a very very low idle and about a minute later it would crank up to full idle. I changed the fuel filters (on top of the engine and under the cab) and also changed the fuel pump under the cab. After that I still have no power when pressing the gas it will still act like it wants to die.
View 14 RepliesOk so the title isn't completely true. It starts. But when it's cold it takes a couple tries. When I say cold I mean Cali cold. Like low 40s. BUT when I have her facing downhill she will start up every time on the first try. What could be causing this?
View 9 RepliesTons of people have had their radios, lock buttons, etc replaced under warranty due to peeling. My driver's side door handle is starting to peel now.
View 1 RepliesFirst off I'm new to the 6.0 powerstroke that being said, I bought a 07 f350 with 102k miles in VERY good condition and I'm planning on doing the bullet proof on it. But my question is that when I start the truck it will turn over about 5 seconds before it starts up. I've even cycled the glow plugs twice with no difference. If I shut it off after it's warm and start it right back up it'll still turn over for about 3 seconds.
View 14 RepliesIf I'm giving a jump:
Assume I hook positive and negative cables to the respective terminals of one of the two batteries. The alternative would be hooking positive cable to one battery and negative cable to the other battery, or does that make 24 volts? I'm also assuming if it is just the one battery, it does not matter which one you jump from?
If I'm receiving a jump:
I assume positive cable to positive post of one battery and negative cable to a good ground under the hood somewhere? Again, does it matter which battery I use? I wonder where a good ground is on this crowded diesel engine and aluminum body. Front radiator supports?
I have an 04 ford 6.0. It is an 03 model. It has 165xxx miles. It fires right up cold but, once warmed up it will crank but not even try to start. A little starting fluid and it will fire right up. I sent the FICM in and had it tested and it is good. I put in new 850CCA batteries and a 185 amp alternator so my voltage is good. I changed the fuel filter and the oil/oil filter, synthetic 5w-30. It isn't throwing any codes. I am really hoping it's not the HPOP but, think it's probably that or related to it.
View 14 RepliesI started having an issue with a rough idle soon after startup about a month ago. I thought it might have been stiction so I added some Archoil stuff the other day to my oil interval change and although I have not put too many miles on it, the rough idle is still there.
At startup the engine runs great. I did notice a few times a little longer than normal crank (~3 seconds) where other times it fires up in less than 1 second. This has happened twice in the last month. Once the engine runs for about a minute I get an uneven idle......I wouldnt necessarily call it a miss per say. I took some readings for the ICP and IPR and can provide them if someone needs them. Once the truck warms up it seems to idle better but still not 100%. I have no power loss, no hesitations jut a weird idle with intermittent surging while in gear.
The truck is starting to surge a bit like an ICP sensor going bad but not as pronounced as the last time this happened to me 4 years ago. Basically trying to get opinions as to what it might be or what to check next. I am leaning toward one of three things.....stiction, ICP or IPR valve (original). FICM voltage is good but my fuel pressure gauge broke, but the blue spring upgrade I did.
2004 6.0 Diesel. First the truck would die after starting, then start up again after a minute. Then the truck wouldn't start at all.
Trouble codes indicated low voltage on all injectors leading me to conclude a dead FICM. Replaced the power module in the FICM and reinstalled, but still no start.
48V at driver's side screw under the cover. 12V at the next screw, the next appears to be ground. The passenger side screw is 0V. One post indicated that should also be 48V - is the true?
I probed the power coming in - logic fuse is good. 50A fuse in the cab is good. Relay seems good.
The Ford FICM diagnostic indicates 12V power should be coming in on FICM connector X3 on pins 7, 8, 4, 23, 24, 25. I have 12V only on pins 7, 9, and 27. When I pull the relay I lose power on pin 27.
Whenever I take off from a stop or slow to a stop, there's a clunk in the drivetrain. It feels like a bit of play before the drivetrain engages and when it releases...torque converter maybe? Taking to the tranny shop soon...
View 10 RepliesMy new to me 2006 F-350 6.0L began having starting issue this week. I'll try to describe it as best I can. Not every time I start it, but about every 3rd or 4th time this happens.
- She will start to crank as if the batteries are weak.
- Very low starter rpm's. If I stop cranking, and immediately try again it will do the same.
- if I wait 30 seconds to a minute, she will go back to a high rpm crank and start up after 2-3 seconds.
I have Auto Ingenuity and a SCT tuner so I can data log PID's.
Just got the pickup a month ago and it is kinda hard starting, has no power until it warms up then it has good power. Today I was driving and it just bogged down more and more until it just died. Would not restart. No master with the multi meter but set it on 200 v and tested the Ficm and it was running between 48 and 48.1 v but one time while cranking it dipped down to 37 fir just a split second. When it does run it would puff white smoke and motor would run real rough. Can't get over 1500 Rpms when it is cold like it is starving. Think it is the Ficm?
View 6 RepliesParked the truck last night and all was fine. Went to start the truck today and let it warm up before hooking up the trailer and it dies withing a minute. Go to start it again and nothing. End up killing batteries. Checked for codes and had a bogus EGR code P0404. Bogus because the tune I run doesn't have the EGR enabled and it is deleted. Still plugged in though.
Hooked up dual battery chargers and sent the boy to pick up fuel and oil filters and oil. It was over due in both areas. Changed both and still no love. So I drag out the laptop and set up my AE to monitor FLP, FLM, IPR, ICP, ICV, Sync.
KOEO
FLP 11.00
FLM 47.0
ICP 0
ICV .24
IPR 14.25 odd right?
Synch 0
Cranking
FLP 9.6
FLM 47.0
ICP 800-1600 varied the longer I cranked
ICV 2.2
IPR 14.24
Synch 1
still no start.
Still no codes.
I then cycled the IPR through AE a few times and turned the key. Damn thing fired right up.
Idling
FLP 11.0
FLM 47.0
ICP 875
ICV 1.4ish
IPR 26.4
Synch 1
I pushed the RPMs up to 2500
FLP 11.0
FLM 47.0
ICP 2200 iirc
ICV 2.24
IPR 42.0ish
Synch 1
Turned the truck off and restarted it a few times. No issues. Turned it off and pulled the positive cables and put the chargers back on it.
So the question is .....Is the IPR sticking on me? I just replaced the HPOP in the spring along with the up pipes. Made sure everything was clean. I actuated the IPR and cleaned it out. Put a new screen on it had zero leaks.
I have a 2006 F350 with around 208k mikes, automatic with a no start, 0 No FICM Sync.
The CMP and CKP has "no / 0" for synchronization and a "NO" synchronization from the FICM. Should this be "yes / 1" when trying to start?
The camshaft position sensor status indicated "yes fault".
FICM is at 48V,
DTC currently on
P2614 camshaft position signal output/open circuit - CMP
Glow plug circuit cylinder 2, 4, 5, 6 (these have been on for 12months and 1,000 miles and never had an issue starting)
B1352 - left front temperature damper motor
B1360 - left rear temperature damper motor
U1900 - CAN - communication BUS fault
I am running all OEM filters