I figured I would try my hand at making a video because I find them useful.. Anyway, if you plan on dropping the DEF tank and /or replacing the heater/sending unit.
2011 -2014 Ford DEF tank removal / sending unit replacement - YouTube
Will the oil pressure switch (sending unit) on my E series van be in the same location as on an F series truck even though the van's oil filter is under the engine instead of on top? I'm referring to the single wire sender for the dash gauge.
View 2 RepliesI recently dropped my tank and one of the connector clips broke taking it off. How can I find anther connector or clip, I have looked at the ford dealer, napa and oriellys with not luck. It seems as if they don't exist. The ford dealer wants me to buy a new fuel line. Also I did something that now I know is not good but I cut the connector out to take to the parts stores and they said that it can not be put back together. Is this true?
View 8 RepliesI've read some treads on the temp gauge sending unit but I'm a little foggy on where to look for my problem. I just purchased a 2000 F250 7.3, temp gauge not working. It has a new sending unit. I read some threads about the voltage at the plug but I have no voltage on either side of the plug. The way I understand it red/white wire goes to the battery. Is there a fuse between them and which one is it? and if fuse is ok is there a cronic problem that someone might know of that I can look for?
View 7 RepliesSo I did the hutch mod several months ago and all was fine.. Couple days ago I went to fill up, cheap diesel, for upcoming trip.
Fuel gauge was working and showing just less than 1/2 tank. Went to Walmart with gift card and started pumping. Got to talking with duramax owner and noticed fuel was finished. did not pop off like the level was high in fill tube just can to end of money..
SO I get in, turn on key to get mileage to mark down miles, gallon, amount etc and noticed the fuel gauge look like it wanted to go up and then it drops to "E" and the fuel light comes on..
Yesterday I drop spare and check sending unit connection which was OK so must be issue with sending unit. ?? So I might need to take camper shell off, fiberglass, and lift bed.. too much fuel in tank and not going to be driving it enough to get down. What size are the bolts holding bed to frame and how do I need do this??
Trying to replace my steering stabilizer and in the process I broke the nut close to the steering box. Would not budge so used a bar and well I broke it. Now I can't pop it out am I doing something wrong? Here are a few pics. I'm totally bummed nothing seems to be working for me.
View 14 RepliesThe trans temp guage on my '08 F-350. V-10 started acting erratically, and the wrench icon popped up on the display. i crawled under the truck to look for the sending unit and it's lead. i assume that i found the lead. it is encased in a corrugated sleeve, and appears to be a vaccuum type tube and boot connector? the boot still had a small round gray cap plugged into it. it appears that the cap was never glued (go figure) upon assembly. i have tried to reach up on top of the trans to find the sending unit to figure out the best angle of attack. i can barely touch it with the tip of my finger. going with mechanical guages is out of the question at the moment, so i'm wondering can it be driven any distance this way, AND any schmooze tricks developed to get at the sucker without dropping the cross member or exhaust????
View 3 RepliesI have finally gotten my 93 Explorer back on the road. Now I have a few things that I am trying to get fixed.
The first things that I need to get repaired is my Fuel Sending Unit replaced. How hard is this and what kind of pitfalls am I looking at.
The problem that I am having is that my fuel gauge is never right. The other day I ran out of gas, but the gauge said full. Go firgure.
Anyway I have been told that the problem is my sending unit in the fuel tank. So is there any advise on this repair.
I have a 99 SD 7.3 with 210K miles. It has the OE water pump, clutch and fan. I am replacing every thing from pump to fan including pulley, thermostat and sensor. The question is can every thing be removed as a unit? I don't see why not but never did one that way.
View 14 RepliesI have an 02 f150 xl, I'm taking the stock head unit out and replacing it with a Pioneer 1900. I didn't buy a connector I'm just splicing the wires together, I know I shouldn't do it that way but it's to late now, what my problem is, there are three ground wires coming from the truck and the new head unit only has one ground, I just looked wiring diagrams up for both head units and that got pretty much everything done, just there are two speaker ground wires that are black and green, and then a regular black ground wire, I'm not sure if I should connect them all together or cap them separately, because I connected everything up and the head unit wouldn't turn on...
View 2 RepliesThe oil pressure gauge is dancing on my 4.2L '99 Ford E-150 (V-6) and at times the oil light comes on but there's no rattling or other signs of oil deficiency in the engine. I'm pretty sure it's a problem with the sending unit and did an oil change today but for the life of me couldn't find where it's located. I looked all around the filter when I replaced it but to no avail. The Haynes manual and internet pics I find are not recognizable parts in them to reference. I can't tell if they're looking under the car, on top, driver's side etc.
View 11 RepliesIm replacing hydroboost and master cylinder and I cannot for the life of me get the master cylinder pushrod (which must be reused) out of the hydroboost unit. There is a spring, retainer and pushrod that I cannot get to release. I know it has to be very simple, I just cannot see how it releases.
View 2 RepliesWhat it is or why there is a three inch pull handle hanging down on the bottom of the Diesel Tank on my niece new 2012 F350??? It is sitting hanging there begging to be snagged and ripped off the bottom of the tank!!!!! I'm at least going to Gorilla Tape it up to the bottom of the Tank.
View 10 RepliesMy question is about a 2000 ford windstar with 3.8 engine. Does this vehicle have a coolant temp sensor and sending unit or just a sensor?
View 7 RepliesI had to replace the temp gauge in my 1996 Explorer. I also replaced the sending unit. Now, it is overheating, badly. I replaced the thermostat, twice. Filled the coolant and removed the air in the system. It seems to get good water flow, and there are no coolant leaks. The radiator looks clean, and the cap looks ok. But, as soon as the engine warms up, it goes right past the midline on the gauge all the way to hot - at idle. It gets worse if I drive it. I have grounded the gauge and it seems to be working fine. What could the problem be?
View 5 Replies3.0 - Where is located ?
View 2 Replieswhere is the oil sending unit on a 1996 ford, E150, 5.0 motor.
View 1 RepliesLifting a crew cab on an 05 6.0 with out a shop lift? I'm going to replace the head gaskets and install studs. I have removed many regular cabs with a tractor front end loader and a 4x5 timber thru the windows.
View 10 RepliesI posted about my steering issue and i went ahead and did the gear box and now on to the ujoints ...
HUB LOCK ASSEMBLY is in 2 i started to gently pry it out with a flat head in a star figure while jiggling and pulling the whole unit with my other hand well ...
The cover plate separated from the rest of the lock and I am lost ...
What's the best way to remove front rotors from the hub without damaging them on my F350 4X4?
View 7 RepliesI thought I remember a posting about removing the radiator to do the cooler because it made it easier to work standing in the engine bay with the engine in front of you instead of leaning over and removing everything from outside ? I'm getting ready to do my 4th external oil cooler? And is it difficult to remove radiator, and/or worth removing it ?
View 14 Replies