Ok so we just replaced our front and rear brake pads and had the rotors turned. Our rear brakes are fine but both our front brakes now make a clunking/popping noise when we brake.
View 4 RepliesWe had approximately 7000 miles on our 2014 250 when we first heard our squeaking when we applied the brakes. This happened after we had been driving a while. Took it to the dealer to see what was causing the noise. They found out it was the front brakes. They removed both front wheels to find the inner pads wearing at an angle and the caliper piston boots partly melted in middle. They ended up replacing the brake pads and calipers with new and machined rotors.
View 14 RepliesI performed brake maintenance today with my brother on my 2010 corolla CE, my front rotors were warped and my pads were used ( and also uneven) and I replaced both front rotors and pads.
The install went smoothly, my brother changed a couple of brakes sets and knew what he was doing and showed me up.
Took it for a spin, the brakes work very nicely ( i bought the ceramic wagner bundle ) but theres a slight grinding noise when driving, like the pads are touching and rubbing a bit too much on the rotor, but the driving is unnafected. Also, there's a sqealing noise coming from either side when you turn only.
Braking itself produces no noise whatsoever, only when you turn that it squeals.
I noticed the front brake pads were touching the rotors when I was painting the brake calipers. I had my e-brake engaged and in park. I'm assuming the e-brake only brakes the rear wheels because the front rotors were still movable. Although the car still rides fine but I'm not sure if this is normal.
View 1 RepliesWhat's the best way to remove front rotors from the hub without damaging them on my F350 4X4?
View 7 RepliesI bought new pads for my truck and the fronts went on with no problem at all, but when I got to the rear the tabs/ears on the pads are about 1/8 inch wider than the notch they are supposed to fit in. I bought part number BR-1067, which is supposed to fit but obviously doesn't. What part number should I have bought? My truck is a 2007 F250 Super Crew Lariat FX4.
View 9 RepliesSo, that means I have put 106,104 miles on my truck this year, and missed about 7 weeks for the truck being in the shop, could have been another 17,000.
So, it's time to replace the factory original brake pads?
I replaced my pads 3 months ago. Now I have a metal grinding sound (not squeaking). The mechanic says I need new rotors, and he will resurface the pads. I know I can replace the rotors myself; but do I need to resurface the 3 months old pads? If so; how will they resurface them?
View 4 RepliesI replaced the front brake pads the same method as a traditional car. (Popped out caliper. Pushed piston in. Put new pads in). I did not pump the brakes after installation (forgot to do so).
I drove off to test drive. A block later as I approached a stop sign, I smelled something similar to burning brakes (this might have been some of the oil I spilled when I added oil just before I left). Went to the next stop sign 100 yards away and was able to stop. Made a slow left turn and MFD displayed a warning and ABS (and maybe other ones too) light came on. I pulled over. I don't remember if the car shut itself or if I turned it off.
Now, I can not get the car started. Had car towed home with wheel lift tow truck.
Tried the following:
- Press brake, push Start: Car appears to power up then shuts down immediately. Lights appear on dash, then go out. The squares around P,N,D,R,B are the last ones to go out.
- Press start to go into ACC mode: Radio and clock power up without problems. Pressing start again results in same symptom above.
- Tried to read code with ODBII scanner: all I get is "ERROR". Appears that it's not linking.
Thumping noise in rear passenger side. I removed pads and rotors, inspected and found nothing wrong. I decided to replace the new rotor with same and the thumping is still there, but only with the brakes being used. Nothing felt in the brake pedel and the the van stops fine. So why the thumping noise?
View 4 RepliesBrakes shimmy on my 05 f150. Been doing this since new new pads and rotors and alignment. what now?
View 5 RepliesReplacing remaining three calipers on my 2006 F-350 2wd as a preventative measure after I had a drag on the left front. Passenger side front being difficult. Caliper won't slide off pads. I believe pins are stuck but it doesn't seem they've got the caliper stuck - appears that I can't get pistons to stay compressed enough to clear pads. Caliper has some wiggle on pads - just not enough.
I tried multiple C-clamp iterations but can't get there just yet. I'd rather not fool with the bracket and removal won't fix my problem, just allow me to work it on the bench. I do have a replacement caliper, so damaging it to get it off is an option. I have sprayed Kroil into the piston seals in a Hail Mary when I pick this up tomorrow.
i have the brake (!) the ABS and the VSC lit up after i got new bearings and new brake pads and rotors, the car was also stalling before the mechanic removed these bearing "dust cover" circles that must have been causing speed sensor interfernce bc the spedometer was stuck on 0....so the car seems to be done stalling after those were removed and all the big lights went off then i hit the brakes a few miles later and those three lights came on...
View 2 RepliesI recently had rotors and brake pads replaced on my 2007 Camry (front pads/rotors and read pads/rotors).
It was done last week and she is braking fine. But sometimes now when I brake there's a low-medium squeaking sound from the brakes. Is this normal / what's the likely cause?
2008 LS600hl with 31K miles, been having low speed brakes shudder for quite sometime even after changing pads and machining rotors. This weekend thought about putting grease on the pins holding the pads, this did the trick, shudder is gone!
View 9 RepliesI have about 50,000 miles on my pads, they look 50% gone, but couple days ago I've got short "beep" and light yellow came on(circle with several small parts of larger circle). What and why? Rotors, pads, other?
View 4 RepliesHow to remove the front brakes pads and rotors on my GMC Sierra 2008 - 1500 - crew cab - 4X4.
View 2 RepliesSo my car has 36 or so thousands miles and well the rear brake pads and rotors were SHOT! The rear rotor was falling apart and huge chunks were coming off. The issue stands now that I can't spread the rear caliper for anything, the ebrake is off too. I tried to use the C-Clamp trick but it honestly didn't even budge. I also opened up the bleeder and master cylinders cap just to cross that off the list when trying to compress. This is the hardest caliper I've ever had the misfortune of dealing with and I fear that the passenger side is not going to be any better. Aside from spending more money or renting the "tool" is there anything else to check because the C-Clamp trick has work on mine and my father trucks calipers.
View 3 RepliesI've had a 2006 Passat 4Motion for about 15 Months now and it just went in for it's 20k mile service. The dealer told me that the front pads and rotors were shot, and the rear pads needed to be replaced.
I've read that the front brakes are rather easy to change but my question is: are there any aftermarket pads and/or rotors that last longer than the OEM ones? I just don't think I want to do brakes every 20k miles. Now in regards to the rear brakes, apparently my rotors are okay but my pads need to be replaced. I've read that you need the VW "Vag Com" to do that and I'm new to VW software stuff.
I'm getting sick of having my rims getting dirty after one hour of driving because of all the brake dust that the OEM pads give off. I keep hearing from shops that ceramic brake pads are not only more quiet but will put out much less brake dust. On the other hand, Lexus is telling me that if I do that, I will forsure damage the rotors but I really feel like they just want me to keep the car stock which is why they're saying that.
Are ceramic brake pads a bad idea with stock rotors?
OK, I just got back from having pads and rotors install on my '99 Passat. I was expecting this to clear up the brake and abs light problem but it did not. The brakes still feel mushy and the ABS light still comes on.What should I check? In the brake forum people suggested bleading the brakes, is this the next step? Any quick how to?
View 3 Replies