Ford 6.7L Power Stroke Diesel :: CEL On For Code P20BA - Reductant Heater A Control Circuit Performance
Mar 26, 2017
Okay, so I have a 14' 6.7L, about 18,438 miles on it and the check engine light came on when I was at the gas station ready to leave, and so I took a field trip to auto zone and they scanned the CEL and it came back as P20BA - Reductant Heater 'A' Control Circuit Performance and they said I need to change out the pump assembly so I took it to the dealership and they cleared the code which worked for awhile, about 4 months ago the light came back on and I'm wonder if I should get the pump/heater changed out or get it deleted? The warranty is going to end in august this year..... It's been fine no issues with the truck, even tho I drive with the CEL on and just wondering what I should do? The CEL has been on for almost 5 months.
View 4 Replies
Advertisement
My check engine light popped on for me a couple days ago. P2043-reductant temperature sensor range/performance. Truck still runs like a raped ape, no change in driveability. Just over 21k miles. No "speed limited to 55" messages or anything else. Basically no change in the truck other than the light.
View 12 Replies
It says "reductant quality performance". I was reduced to idle the other day at the boat launch, with my boat. Called roadside assistance to come get the truck. They said they weren't liable for my boat, had to call a friend to come get it. Bring the truck to the dealer and he blames it on the DEF I bought, non motorcraft. I purchased ford DEF, siphoned the old stuff out and refilled with the ford DEF. Went out of town on a fishing trip and got the CEL again.
View 14 Replies
I keep getting a problem code of P0404 - EGR Circuit Range/Performance. What it is and if its a serious issue?
View 2 Replies
My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.
P02E1 - Diesel Intake Air Flow Control Performance
The air box gauge is green and it doesn't reset when I push it so that appears to be fine.
The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.
Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.
I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.
I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.
View 4 Replies
Sunday I received the dreaded DEF system fault message on my 2012 CC SRW SB FX4 with 7800 miles on it. Warned me that speed will be reduced to 50 MPH in 50 miles. I have a CTS Insight, so I checked for DTC's. First one was P2200 - NOx sensor circuit (Bank 1, Sensor 1), the second one was P204F - Reductant system performance (Bank 1).
After 50 miles it warned me that speed would be reduced to 50 MPH on next restart. Sure enough, Monday morning speed was limited to 50. I took it to the dealer, but I should have left it running. When the service guy started it, the fault had cleared and it no longer showed the P2200 NOx sensor code, although the P204f code was still there.
My question is, why in the world would Ford make it so that the code is cleared if the fault goes away, especially after putting you through the 50 MPH limit scenario?
Dealer did a reflash and said its OK now, but I'm not so sure. My trucks build date is 10/6/11. I read TSB 11-11-13 which states the NOx sensor module should be replaced for P2200 on trucks built before 10/11/11. Is that only for a persistent P2200?
View 5 Replies
I have a 2012 6.7 with a Spartan tuner. Threw this code a few months ago. Reset everything, trucks runs great, no issues. Never had this code come up again. I've looked it up and it says, "Internal Control Module Torque Performance". I'm just not sure what this means.
View 2 Replies
I have an emissions test coming up. I have 3 P codes that I'd like to eliminate before then. I don't want to "fix" the issues they are telling me about. Just make the codes go away. I know why they're there I just need to get rid of them.
What I have coming up is:
P0475 Exhaust Pressure Circuit Valve (result of EBPV delete)
P0541 Intake air heater A circuit low (result of aih delete)
P0640 Intake air heater control circuit (also result of aih delete)
What resistors I'll need and where to put them in?
View 12 Replies
2004 Excursion 6.0L .... Recently after a 200 mile trip through the mountains running good, I get home and the next day it idles down the driveway at a high idle and after a few minutes seems to run better but within 5 miles the CEL comes on and throws P2287 - intermittent injection pressure control circuit. I cleared the code, ran around town again and the light came on again same code. I'm getting appropriate ICP-voltage and pressure readings. I took it home sat overnight and thought I would pull the ICP sensor.
I replaced the ICP sensor less than 6 months/5,000 miles ago. I also changed out the main engine harness at the same time. I looked at ICP sensor and it looks clean. Started the truck and tried the scientific wiggle test while running and monitoring ICP-voltage. Started at the sensor bending and wiggling back to FICM. No fluctuation in voltage. Ran the truck around town, 20 miles and no light. Yesterday we made the same 200 mile trip over the mountains, seemed to run strong. In town this morning within 5 miles the CEL is back on and the only code is P2287.
My Ford powertrain diagnostics manual doesn't have the P2287 code in it for troubleshooting. Should I go after the FICM, and how do U test that if so? I'm currently that 200 mile drive from home and don't want to damage anything more.
View 8 Replies
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies
CEL came on in my 2013 6.7L with 74K miles a couple days ago. Pulled the code today and it was a P263C - Glow Plug Driver Performance code. Any remedy for this.
View 8 Replies
2006 F350 6.0 throwing code P0480 and I'm having a hard time figuring anything out pertaining to my truck. Trying to figure out what exactly it is and how to fix it myself.
View 3 Replies
Over the past weekend I had to replace all of the egr gaskets and seals, due to it failing smog. I removed all of the harnesses over the motor, intake manifold, turbo, and oil filter housing. I also replaced the oil/oil filter and also the fuel filters. The truck ran great before I decided to replace all of the seals. When I went to start the truck, it would just crank and not fire. One thing I noticed was that my wait to start light only stays on for a few seconds, where before it would stay on for a while. After cranking on it for a while I got a code P2623 for the ICP circuit open. I have tried unplugging the ICP sensor to see if it would start, but it just cranks over. The truck sounds like it wants to fire, but wont. Should I pull the ipr and ICP sensor?
View 4 Replies
I have a po6a7 code boost gauge pegged at 40 code says vref circuit b out of range. What sensors run on circuit b and what could possibly be the problem my camshaft sensor is reading fault on scanner don't know if that has anything to do with it taking the truck to the dealer is not and option it's a 2011 6.7 with 75,000 miles....
View 1 Replies
Have a 2004 F350 which had problems starting cold and once started had bad throttle response until warm. It also had a shudder at cruising speed when going up a slight incline, would shudder until turbo kicked in.
Pulled codes which related to FICM and codes for all 8 injectors. 7 injector codes were circuit low, cylinder 1 high. Tested FICM voltage and sent FICM out for repair.
Installed rebuilt FICM, cleared codes, and hard start went away, but cruising shudder is still present.
Only existing code is P0262 for cylinder 1 injector circuit high. I'm assuming that cylinder 1 injector is bad -- are there any tests to confirm before I take it apart to replace it?
View 7 Replies
So yet another crank no start. Truck is an 03 55k miles The guy I bought the truck off of told me the turbo had been reconditioned about 1000 miles ago. Drove the truck another 1000 miles or so and now having issues. I went to start truck up and noticed it took awhile longer than normal to start up and when it did finally kick over, truck and no power at all. Would idle a bit rough sounded like no turbo spool at all when given throttle. Shut the truck off right and hooked up scangauge to it went to start it and nothing.
Did throw p2285 code ICP low circuit
Values read on scangauge are as follows:
FICM Main Power 48.0V
FICM Logic Power 10-8V
FICM sync is good
ICP Pressure 1540psi on crank
IPR duty cycle 14.8% Key on engine off/48.8% while cranking
At a bit of a loss as to where to look next, would really like to troubleshoot down to the right fix instead of just throwing parts at it. Have read after sitting the turbos tend to stick and need cleaned or replaced. After being cleaned only a few thousand miles could it be stuck again? Seems like I have spark, fuel, oil just acts like its not getting any air.
View 13 Replies
On a family vacation in our 2013 6.7 pulling a 41ft trailer to the Seattle area from Alberta Canada. Made it to destination yesterday. Woke up this morning started truck and cel on. Bought a code reader at the local napa store and read P206 fault inj 6 open circuit. Any thoughts on driving the truck around with a inj fault? Thought I had read here some where that 6 was the regen cylinder.
View 14 Replies
I bought my truck 2 month ago. I use it for commuting, only short trips now ( 10 min ). After about 2 weeks the Check Engine light came on. The truck is running fine, no problems I believe, starts easy. After another 2 weeks, the CEL disappeared. Another week, and the CEL came back on and it`s there since. I have a code reader, these are the codes and meanings according the manual:
P0299 - Turbocharger "A" underboost condition
P2286 - Injector control pressure sensor circuit high
P2287 - Injector control pressure sensor circuit intermittent
P0299 Pending - same as first but with "pending" status
This is my first diesel and my first turbo charged engine. Is this a common problem? How serious? It`s a bit strange that the error came up before but disappeared. Can that happen just because of the short trips I`m making? I`m planning a long trip soon with towing my trailer, so I want to make sure the truck will not break down during the ride.
View 14 Replies
I have a 2007 f250 and got a check engine code icp circuit intermittent and to what I know icp sensor should be on the valve cover on the passenger side but it's not I bought the truck few months ago could it be that they swapped the engine for an early 6.0 or is there any other place for the icp sensor???
View 7 Replies
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 Replies
