Ford 6.7L Power Stroke Diesel :: CEL Code U059E - Invalid Data Received From NOx Sensor A
Jan 21, 2015
Right around Christmas. Hubby used the code reader and found this:
U059E - Invalid Data Received from NOx Sensor A
And then cleared it. CEL went away and hasn't been back since, so my question is, am I safe? Was it a fluky reading on a cold day of making short errand runs? Or did I have an actual problem even though the CEL has not come back? Truck is running fine, no issues (knock on wood), and I'm not really worried - just curious more than anything.
View 9 Replies
Advertisement
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 Replies
I have a little over 32k on my 2014. Left today for my first camping trip of 2017. 250 mile into the Eastern Sierras. Took a potty break after 125 miles or so and CEL came on. Used my CTS2 and got a P2201 code which is a NOx sensor. I decided to continue on to my destination and made it there safely.
My question is do you all think I will be ok driving 250 miles back home in a couple of days? Truck seems to run ok. MPG seems to be dropping.
Interestingly, the Soot % on my CTS2 dropped to 0% and stayed there the whole trip. Obviously it's going to the dealership come Monday, just wondering if I will make it home ok and not get stranded in the desert with the family.
View 4 Replies
So my truck decided to throw out the EBP sensor code. I am noticing a bit of power loss and funny noise when I let off the gas. I am 200 miles from home and not near a town or parts store at the house I am working on. Is it safe to drive the tuck the 200 miles back home tomorrow. I have a very important appointment I can't miss. I will be putting the new sensor and harness on tomorrow Evening
View 3 Replies
Where is the ICP sensor located?? I am getting code P2285 and according a to a Ford Message this may be because of a bad connection that there is a kit to fix it.
View 14 Replies
2004 F350 Lariat 6.0 Crew Cab 6spd... I just bought this truck a month or so ago has been a great running truck since. Before I got it it had headgaskets done, egr valve replaced, and new injectors installed.
Yesterday I shut it off and was setting up my scangauge and doing few other things and noticed I ran the batteries down to 7 volts. So I unhooked them and charged them seperately and cleaned the posts. Now today it won't start. Voltage shows 12.3 FICM logic and main both show 12v and FICM shows 48.5 and doesn't lower when cranking. CMP/CKP shows its not syncing and I am throwing a cmp sensor code. Its had the code since I got it and I've cleared it but always comes back. I've read its rare for a cmp sensor to go bad so I'm wondering if it sounds more like the wiring just seems strange its first time it wouldn't start and hasn't had any other problems.
View 2 Replies
CEL came on today on my 2011 F-250 6.7 with 48K miles. It did not show a message or shut down. When I checked the code it was P2479 EGT Out of Range Bank 1 Sensor 2. I was reading about a letter last year, which I did not receive, concerning an extended warranty. My questions are: What is the part number? How are they identified and located in the exhaust system? I found a diagram stating: EGT 12, 14 ect? How does that correlate to Bank & Sensor?
View 13 Replies
I had CEL the other week scanned and found P2043 Reductant Temp/Sensor range. Light came on first thing after a cold start.
View 13 Replies
I have a 2004 6.0 with 75000 miles on it. My truck is throwing a P0470 code pointing at the exhaust pressure sensor. my question is do I need this sensor or can i bypass it? When I look up the part it only shows 2005 and up.
View 6 Replies
Replace the tft but still the problem, someone cones the number part of tft sensor harness, and as replace , 2006 f350 4x4....
View 2 Replies
My check engine light popped on for me a couple days ago. P2043-reductant temperature sensor range/performance. Truck still runs like a raped ape, no change in driveability. Just over 21k miles. No "speed limited to 55" messages or anything else. Basically no change in the truck other than the light.
View 12 Replies
I'm excited to be a Powerstroke owner again! I had a 2000 with the 7.3L and since bought and now sold a Chevy 1500. Last week I bought a new 2015 6.7L. I am MORE than impressed and love the truck. Today I brought it to get the windows tinted. I have not had one issue with the truck since I have had it. When they finished with the windows, my check engine light was on. The shop I had it done it EXTREMELY reputable. They brought out their snap on scanner and pulled the code. p0073 for the ambient air temp sensor circuit high. Is this a coincidence that this came on after they got done, or could something they did while tinting the windows tripped this?
As I drove off down the road after determining I wasn't going to hurt the truck, the air temp sensor went from showing -40 to the actual temperature. What would cause this? I deleted the code when I got home with my actron, and the MIL has stayed off since, however, it shows P0073 Permanent ...
View 11 Replies
Just over 6000 miles....Yesterday morning the light came on. Dealer wouldn't look at it for a week. Went to my mechanic this morning to check the code it was p0181 fuel temp sensor. I read something online about the block heater making it too warm. The other night it was cold so I plugged it in, then yesterday morning it got warm overnight like into the lower 40s. I noticed the grill felt warm too. My mechanic cleared it if it comes back on do I have an issue? Is it ok to drive?
View 14 Replies
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies
2012 GTI. DSG My airbag was blows, so I replaced it. Now im getting the following code.
18036 - Powertrain Data Bus
P1628 - 000 - Missing Message from Steering Angle Sensor
Can the sensor go bad after the airbag was blown? All the steering wheel controls still work.
View 4 Replies
Check engine light is on, when I went to get my car inspected it was showing an invalid vin code. How do get this off so I can get my emissions done?
2007 Santa Fe SE
View 3 Replies
My truck had to be towed to the shop today. The wife and I were stranded for 2 hours and to say I was upset is a understatement. My truck has 13,800 miles and this type of failure is unacceptable. Is it necessary to carry extra sensors around in order to get your truck off the side of the road? BTW, my truck didn't even make it to the side of the road, we had to push it to a narrow shoulder on a busy side road.
View 14 Replies
I am award of the problem. And hope to be one of the majority that never has to deal with the issue. But, if the problem were to happen and the code thrown could it be as easy as to pull over. And if you had a code reader that could clear code.
Could you simply clear the code and be on your way? If so, how far would you get before the code reappeared and you had to repeat the read and clear the code again.
View 5 Replies
was looking for the oil pressure sensor and can't find it got it narrowed to 2 there is a sensor between the the oil filter and fuel filter i think thats the temp sensor and then there's 1 at the say 11 o'clock position behind the the oil filter...both have a 2 pigtail connector.
View 4 Replies
Had CEL light and took truck to dealer and they replaced Bank 1 sensor 4, two days later, CEL again Bank 1 sensor 3.
I've trouble shot many EGT sensors on Airplanes, and we could tell if there was a failure coming if a couple failed by testing the sensors themselves. My Service Manager told me there is no way they can check the others out. That sounds like Bull to me.
View 1 Replies
Truck has been running very well while in the warmer North Carolina climate pulling trailers with no limp mode or wrench light. However, when daughter started the truck this morning, SGII showed one DTC and when she pulled it up it was P0675. OK, glow plug num 5 maybe or the module. No issues starting or rough cold idle. I told her to clear the code and we'll see if comes back.
She did ask if it is something she should have it repaired before the trip back to Vermont. So I thought I'd ping the group here since reading posts, they seem to be fairly easy to replace (and assuming it isn't a chafed wire) and I could probably save her some $. Just want to make sure there isn't any chance of real engine damage.
View 4 Replies
