Last night we had some serious rain and I went through a pretty deep water puddle at speed. I didn't see it until I was right on top of it. This morning I see a vent line of some sort hanging under the truck. The end is attached to the real axle on the left side and on the other end is a plastic connector. I have searched high and low and can not see where this connects to.
View 6 RepliesI noticed a vacuum line hanging under my 98 F 150 4x4 I traced it out to my front axle question is where does the other end go I have looked but no luck to where it goes.
View 5 RepliesWhat it is or why there is a three inch pull handle hanging down on the bottom of the Diesel Tank on my niece new 2012 F350??? It is sitting hanging there begging to be snagged and ripped off the bottom of the tank!!!!! I'm at least going to Gorilla Tape it up to the bottom of the Tank.
View 10 RepliesWell I just noticed the rear axle air vent and it is blocked.. I ordered a new one and will replace it once it arrives.. what can I expect once I replace it?
View 2 Repliesso while replacing the rear brake lines in my 2001 F-250. / 5.4, the flex line that drops from the frame bolts to the axle through the axle breather threaded vent line. The friggin thing crumbled on me and now I can't find a replacement for it. Where I can get it or what it's actual name / part number is so I can call the Ford dealer and hope it's not obsoleted?
View 3 RepliesMy 2006, King Ranch, 4x4, 6.0's air conditioner only blows from the defrost vent. I have done some research on here, but haven't seen anything that identifies as a common problem. I did however, notice that this problem is stemming from a vacuum issue.
View 10 RepliesWe just got back from our first trip towing our 5'er. One of the things we encountered was the sun glare coming off the chromed air vent ring bezels. I am probably going to have them powder coated to stop the reflection. How to take the rings off the truck?
View 2 RepliesMy Front axle wont go back in! It kinda was a pain to remove too; but getting it back in is like mission impossible! I've tried turning the driveshaft, the other wheel, all kinds of stuff short if beating it with a hammer.
In an hour or so I am going to take off the diff cover and see if there is anything obvious, Id rather not but... I took it apart due to noises I was hearing up front on that axle / hub. I have all new seals and such just in case anything needed it.
So I noticed the other day that my front axle is tilted forward a little bit. Would this cause any problems or will it be alright.? If it's going to cause problems, how can I fix it.?
View 14 RepliesI have both a hydraulic dump trailer with two 12v batteries and an RV trailer with two 6v batteries to supply 12v. Both trailer's batteries are wired to be charged from the tow vehicle if the TV is equipped with a charge line.
Does the OEM 7 pin connector on a 2005 Ford 6.0 F250 CC 4X4 have a charging line on it? If so which terminal / pin is it?
What gauge of wire is it and how much amperage will it deliver to the connector? For testing, when is it hot? When the truck is running only? When the key is on? Is it hot all of the time?
Couple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 RepliesSo I replaced ball joints and hub bearings on driver side of the truck today ( passenger side tomorrow). Problem is when I pulled the axle out gear oil started to leak from axle housing not a lot but a leak nonetheless. Is this normal or did I break something.
View 2 RepliesI am thinking about changing the Gear Ratio in my 2014 Platinum F350.
History: I traded in my 2011 F350 DRW with 17" wheels and 3:73 gears to get my 2014 F350 SRW 20" Wheels with the 3.55 gears. I pull a 15,000 boat and trailer. The Drw pulled the boat and trailer with no issues. I sold my Northern Lite Truck Camper. I thought I didn't need the Drw any more. First time I hooked up to the boat I felt the difference in between the trucks in the acceleration and fuel economy. Old truck would get 11.5 MPG new truck gets barely 9 MPG going down hill with a tailwind. Over all the new truck is a little slower off the line but when hooked up to the boat it is a dog with the 20" tires.
So the question to you all is; gear change to 4.10? Swapping to this ratio with 20" tires will produce the similar RPM's and possible improve the fuel economy. I get around 18 empty now on trips empty. Around 16 commuting 25 miles to work.
I have to change out the inner seals on my front axle on my 04 f250 6.0 4x4. was wondering what the torch spects are for the bolts on the end caps and the torch spects on the differential cover? I already have the passenger side axle out. was changing my ball joints on that side when I noticed a bunch of oil in the axle case and on the hub knuckle. Also, this might be a long shot but is there any way to change the inner seal on the drivers side without taking out the axle on that side? I have the passenger out and if I could get away without pulling the driver side that would be awesome.
View 10 RepliesI took the front axle shafts out a couple months back and remember NOT seeing any differential fluid in the axle shaft housing. But then when I took the tire off tonight.. I noticed diff fluid leaking from from the axle shaft dust seal ?
1. I didn't think diff fluid flowed up near those front dust seals ?
2. That's a brand new dust seal so I'm guessing some debri must be in the connection causing the leak ?
I've found everything there is to know about disconnecting the high pressure oil STC line from the oil rail on the early 6.0's, but I can't find anything about reconnecting them. Do you simply press it back on? Should there be an audible "click"?
View 14 RepliesWent to go and start my truck this morning and noticed after it was running that it sounded like a misfire, then i seen the smoke... I shut the truck down and lifted the hood and seen that somehow i had a high pressure fuel injector supply line on the Lh side break off. The line that goes from the fuel rail to the injector port on the valve cover (theres 4 of them on a side). There doesn't seem to be an o-ring or anything on them, they are just pressed over and tighten down.
View 6 RepliesThe ford dealer in Las Vegas replaced my turbo with a remanufactured one. Coming off the line (like quickly pulling into traffic) it goes flat on power until I get a few RPM's. Even with the old turbo it never did that and I drove it for the last 30k miles with it throwing the low turbo boost code. They put a little over 100 miles on it for road testing (I did have other things that they worked on. {4x4 2006 F250, 6.0 engine, 110k miles and I bought it new}....
View 4 RepliesI have 2006 ford f250 6.0 diesel. I was changing the fuel filter on the frame rail and noticed a lot of dirt in the housing . I tried to remove the plug to drain water to see if i could get out some of the dirt. But the bolt just turned and wouldn't come out. It wouldn't tighten either. I went ahead and cleaned as much dirt as i could and changed the filter. How to get the bolt out....... I just bought the truck so i don't have any prior maintenance history...
View 4 RepliesI was updating the firmware on my mini max tuner today and decided to calibrate for the 37" tires. After calibration was done I got the code P1635, which is "Tire/Axle Out of Acceptable Range". Should I bring it back down to 34" where the FORD ECU stops calibrating? I mite have lost traction control with this calibration as well. Mite find out tomorrow if I get an itchy foot. Truck seemed to drive better and pull harder off the line....low rpm's.
View 14 RepliesI am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 Replies