Ford 6.7L Power Stroke Diesel :: Automatic Exhaust Braking Working In Tow / Haul Mode
Jan 28, 2016
Quick observation: with the exhaust brake switch off, I notice it appears that the exhaust brake is still working automatically when you are in Tow/Haul mode and apply the brakes coming down a hill.
I notice the engine drone and turbo boost gauge rise...although neither the drone nor the boost are as noticeable as when the switch is turned on.
I know the 2011-2014 had "auto exhaust brake only" but it appears some of that functionality is still built in.
Another question: what is the consequence of turning the exhaust brake on and leaving it on for normal driving? Is mpg affected? Engine output? Engine wear?
View 14 Replies
Advertisement
It's on my 2015 f-250....dont know if this is a new thing ..... I know my 2011 f-350 didn't have it..... Really hardly notice its working ....it slightly slows me down when in tow/haul mode while braking......
View 14 Replies
Is there a way to auto engage the Tow/Haul mode when you plug in a trailer that requires brakes? Be nice since I sometimes forget to push the button after we stopped for lunch...
View 14 Replies
How do you diagnose a bad fan clutch? When driving in tow/haul mode I get a noise like a jet engine. It starts going down grade or upgrade and does not stop after leveling out. I have switched off tow/haul and it is still there. Over on the Diesel Stop site I found a couple of guys who have had the same problem. Concern is everything I have read there are no codes thrown. Have not taken to my local Ford Dealer to see what they say.
Driving a 2011 F-250, August 2010 build date with 76,500 miles. Problem started about 6 weeks ago when pulling an 8000 lb travel trailer in the White Mountains of NH.
View 14 Replies
I have a 2012 ford f350 SRW 4x4 with the 6.7L. Problem I have just started to have. When going downhill in tow haul the truck at first will hold you back then all of a sudden it starts to up shift at 20 mph it reaches 6th gear pretty quick. I talked to the dealer and they suggested I was pushing the shift buttons, but I am not. They told me to drive it till next week and then they will see if there are any codes in it.
View 14 Replies
I've done it before but now when I try to enter into the diagnostic mode I'm not getting anything but the typical message center. I'm holding the down arrow button, inserting the key, and then starting the truck. No diagnostic mode. Am I doing something wrong? 2011 F250.
View 1 Replies
So driving the other day and tow haul starts flashing. I come to a stop sign and goto take off and it barley takes off. It will barley roll if my foot is off the pedal sometimes wont even roll. Also won't shift into 6th. Once it gets rolling though say till about 25 it's fine. Just doesn't wanna take off? I scanned the trans but got no codes. And here are some pressures and stuff but I don't know what I'm looking for with the trans. This was all done in park.
View 14 Replies
Never really intended to tow heavy with my truck. But heavy towing seems to have found me. I've been hauling dump trailers to the local demo site and I've been toying the scales at the site between 21,000 and 28,000 lbs (way more than I want to haul, but my boss is a cheap jerk and won't stop loading the trailer until the straps barely make it over the trailer). My intent is to dump the thing right where he loads it next time he does it, as I've asked him to quit putting my wallet and maybe life in jeopardy.
Any way, my tow haul button hasn't worked through any of this. Am I murdering my tranny? The engine seems to grunt through just fine. But I'm worried about the fact that it doesn't down shift to go up hills.
View 11 Replies
Have a Gage fault and tow haul flashing on the dash have no clue what is going on?
View 8 Replies
In addition to significantly louder noise from the Turbo on start-up, we've started to hear a pretty concerning noise while descending a hill in Tow-Haul. Not sure that the T/H has anything to do with it other than getting the engine in a RPM range that causes the noise. We've taken it in and tech says "That's just normal noise"... What ever that is.
Here is a link to an example : Tow haul making a lot of noise in my F350 diesel. Pulling a very heavy horse trailer. - YouTube
Best next steps for a 64,000 mile 2012?
View 8 Replies
My co-worker has an 06 F250 SC 4x4 and is getting a P0713 code. 2006 Ford F250 6.0L Diesel ... Tow/haul light comes on flashing at random times. Truck is reading a P0713 code which is the TFT Sensor Failure/Replacement
Ford dealership is telling me that I also have to pull the valve body and install the new upgraded wiring harness (3-3.5 hours labor) but a thread on this forum stated I just needed to replace the sensor in the tranny pan and reconnect the wire harness. Do I need to upgrade the wiring harness?
View 3 Replies
I have just bought a 2004 F-250 SuperDuty 6.0 Diesel with 98k miles from a Ford dealer (no warantee)...
Just after I drove it home I noticed the Tow/Haul mode switch was not working - no dashboard light and no transmission downshifting.
The dealer took the truck back in and kept it for 2 days, it came back working, they claimed to have replaced the gear shift lever. 500 miles later and the Tow Haul has failed again.
View 14 Replies
Title says it all. Chirping sounds almost like belt noise but appears to be coming underneath the vehicle (and from further back than the drivers seat). Goes away as soon as I turn off tow haul (which provides engine braking). A quick visual inspection finds nothing amiss. Trucks runs and drives normally with or without tow haul.
View 14 Replies
I have an 05 Excursion and I drove and parked it, no problem. Came back out and the trouble began. I looked on this site (always do for the best guidance and info) and replaced the trans position sensor, put tunes back to stock. Since then, I have had intermittent issues with the truck only starting with the code reader plugged in, idle jump to 750 rpm, and the tow/haul light flash and won't shift into OD. It also seems at full stops it is not in the low gear. I am driving it to the "stealership" today to have the computer flashed. Additionally, the blinkers won't flash, they only illuminate. All this started at once. Where all the ground straps/wires are??
View 6 Replies
My friend has a 2006 F-450 and he said the Tow/Haul light blinks and the shifts are real slow. He has stopped towing now and it still drives.
I have read everything from toasted tranny to chaffed wire harness across tranny crossmember to the TFT sensor. My guess is the TFT sensor given his symptoms. If I am right the sensor is just to the rear of where the dipstick comes thru the tranny case. 1/4 turn and pull it out. Kinda like a bulb I guess.
Another question, is it necessary to replace the harness while in there as well? Is the Connection listed below the harness I am asking about? I found these parts on a thread from here:
Sensor (1): 3C3Z-7H141-AA;
Connection (1) 4C3Z-7G276-AA;
Gasket (1): 3C3Z-7C155-DA;
Fluid (10): XT-6-QSP
View 9 Replies
Okay so I just peaked 100k and (of course) my 6.0 has an issue. I was driving along when suddenly my Transmission Temp gauge dropped to nothing, the tow haul began flashing and my check engine light came on. My transmission hard shifted and wouldn't shift up from 3rd. I let the truck sit for a few days, no leaking was observed and no blown lines. I added 4qts of tranny fluid and went to take it for a spin. The truck did fine for about 20 minutes and the same issue occurred. I parked it and checked the dip stick and it was full. What could the issue be.
View 5 Replies
Have a 2003 F350 srw 4x4, 107,000 miles on it. Driving it last night tow/haul light started flashing, hooked up AE got a P0730 Incorrect gear ratio. Truck seem to do ok, cut it off went back out a little while later and the tow/haul didn't flash.... Only issues I've had is when shifting from P to R, it takes a second or two longer than it should and shifts hard when it does but it doesn't do it every time.
View 1 Replies
2004 F-250 6.0 Turbo Diesel W/ Torque Shift Transmission. Im having a problem with my Check Gauge light coming on and Tow Haul light flashing on my 04 F-250. I got a Transmission Fluid Temperature Sensor from my local Ford Dealership. They also said i needed to replace the Transmission harness for this application because of an open circuit.
My questions are, Is Mercon SP the only ATF that can be used on the Torque shift transmission and do i really need to replace the harness or just the sensor? I have read up a little on this and so far everything say's drain the fluid, drop the trans pan, swap out the sensor, replace the trans pan (torque setting is 11flbs I believe, correct me if I am wrong, replace with Mercon SP ATF and your good to go.
View 10 Replies
Friday I pulled my steel gn 3 horse trailer about an hour each way. with the horses it weighs right at 7000 pounds. no issues. Saturday morning I drove to town, no issues. Saturday evening, I got in it to run down the road and about 2 miles from the house, the check engine light came on and the tow haul light started flashing and the temp gauge is dead. drives and shifts normal, tow haul button still functions. Truck is stock except for an EGR delete. No tuner, FICM was rebuilt. I had it on a battery minder before I left and was thinking about pulling the batteries and letting it sit for a while to see if it clears. Scan Gauge II shows no codes.
Sunday: So I let it sit all night, batteries connected and it was completely normal this morning. will see what happens when I drive it to work tomorrow
Later Sunday evening: So I just took it out for a test drive, went a couple miles down the road, shifting normal for a cold start. Temp gauge is working, just as I am almost back home. 5 miles at the most, temp is coming up to normal, gauge goes dead and check gauge light comes on and tow haul starts flashing. I think it might be the sensor.
This morning: I got about 6 or 7 miles from home, trans just got up to temp, pulling up a hill, it shifted out of overdrive, tft gauge went dead, check gauge light came on and the tow haul light started flashing. still shifts like it always has and the tow haul button still functions.
I am thinking it is just the temp sensor. Truck has 159k on it.
View 13 Replies
I've topped up the DEF and the warning is still showing that I'll have reduced engine power within 45kms.
Its weird, just yesterday it showed 550kms to empty so I added one full container, all day it kept showing less and less kms' til empty. Warning lights and bells etc.
This evening topped it completely and still shows. Is there a way to reset it without having to stop at the service dept.
View 14 Replies
Well I've been towing for almost 150,000 miles with a 2012 6.7 Lariat 4 wheel drive. Things have been going pretty well with the truck. I noticed some sluggish and indecisive type shifts early on but now I'm worried. I depend on this truck for pulling a horse trailer all over the country and Canada. Just recently I've been getting a hard shift or a thump or a clunk when shifting up or down in to second gear. I'm at about 152,000 miles and did a hot flush with LV ATF at about 148,000 miles. Should I worry or keep running?
I have a 97' PSD I'm thinking of giving a nice paint job and a flat bed but am reluctant to do so due to financial concerns and the fact that some folks may not want to see me pull up in an old truck no matter how nice it looks. My tranny temps have been stating under 200F and I really keep an eye on the temps when running up and down the hills while towing. The trailer is a 35' Gooseneck with a max GVRW or 14,000 pounds. Should I wait for the tranny to grenade and then drop in a built tranny and if so who's building these tranny's stronger than stock? Long time no see but this site has always been my go to for all my Ford truck questions, upgrades, etc.
View 5 Replies
