Now I have an airbag lamp that stays on, gonna have to take it in for this one. Getting funny DTC's also:
P0480 Cooling fan 1 ???? seems bogus to me!
B0001 Cannot find a description, but seems to be a BCM Code, may be attached to lamp?
2006 F350 6.0 throwing code P0480 and I'm having a hard time figuring anything out pertaining to my truck. Trying to figure out what exactly it is and how to fix it myself.
View 3 RepliesEvery time I start the truck, the Passenger Side Airbag light is on, which is saying the airbag is turned "OFF." I have to push the button to turn the light off, which turns the airbag "ON." How do I reset this to where the airbag is "ON" until I turn it "OFF?"
View 8 RepliesI have another problem going on with my Sub. The ABS light stays on all the time. It has new sensors all the way around. I replaces all the brakes when if first bought this overgrown bobber. Is there something to look for that could cause this? Elsewhere?
View 6 RepliesSo I re filled with DEF fluid the other day and the warning light is still on and miles declining every time I turn on the vehicle to drive. Running out of miles before it says empty even though its not. Dunno if i'm able to make it to the dealer right away to get it fixed.
View 14 Replies2003 F250 6.0 ESOF - 4x4 and LOW lights on, TC not shifting
About the truck: 2003 F250 CCLB 6.0L 210k Miles
Heavy Duty Bulletproof Diesel Kit
Warn Front Manual Hubs (vac lines clamped/blocked)
Transfer Case Shift Motor/TCSM is off (I personally have not tested it and am still looking for what to test on it) or I will purchase a new one.
From seller: "What happened is, I accidently put it in 4x4 and when I turned the switch it would not go out. I had to limp it home slowly. When I got home I messed around with it, and could not get it to go back into 2x4. I removed the shift motor, and tested it. It tested ok. I shifted to back to 2x4 with a wrench and left it."
CURRENTLY the TCSM is off the transfer case and is in 2WD. Warn hubs are set to "FREE," seller also noted that this is how he has been driving it for quite sometime. TCSM is in 4x4 LOW, that is what I have to manually shift the transfer case to if I want to mount it up. I have been shifting it using a 14mm open end wrench and with the transmission in neutral. I have not tried turning the TCSM position manually.
Scanning using AE brings up different codes depending on transmission position and which scan is used:
P1812 4-Wheel Drive Mode Select Circuit Failure
P1819 Transmission Neutral Safety Switch Short Circuit To Ground
P1832 Transfer Case Differential Lock-Up Solenoid Circuit Failure
P1876 Transfer Case 2 Wheel Drive Solenoid Circuit Failure
P1865 Transfer Case Contact Plate Power Short to Ground
AE scanning for DTCs: P1832 and P1876
AE scanning using OnBoard System " SYSTEM SELF TEST" with transmission in PARK: P1812, P1832, P1876
AE scanning using OnBoard System " SYSTEM SELF TEST" with transmission in NEUTRAL: P1812, P1819, P1876
AE scanning with TCSM off: P1865, P1832, P1876
P1865 seems to be solved by simply installing the TCSM.
AE Live Data shows correct indicators for 4WD switch, showing corresponding drive mode in AE as the switch setting but nothing happens. No clunk/thud/movement. I have tried resetting the codes but the 4x4 and LOW lights both stay on. I tried it in park, neutral, engine off and engine on. I tried driving 5-10 mph to relieve any driveline wind up, I tried driving in reverse with front hubs free and locked, gave the same results in AE and no transfer case shifting.
Section 308-07A Four Wheel Drive Systems Pinpoint Test I
Found a thread with some fuses to check, I have checked fuses #19, 27, 31, 33, 34, 45 and 111 (with a multimeter for continuity),
Relays (first swapping the old ones, then trying new ones), I did the pinpoints from test I, and installed another GEM (same part number as mine but from a 2005 F-350)
Section 308-07A Four Wheel Drive Systems Pinpoint Test I led to my purchase of a used GEM, not knowing if it is good or bad, I have determined that I get the exact same codes for each AE Scan as the GEM that came with my truck.
I included a photo of my relay box, have any of you seen this type before? There is no other box in the engine bay with twin relays.
Air/Defrost switch works and routes air to switch setting. AC works, DEFROST works.
Could PVHS be causing a code from the manual hubs?
Could the MSS be causing a code even if it is showing correct in AE?
Should I try a new TCSM? Should I try turning the TCSM manually? How do I test, what do I test for on the TCSM?
I want to avoid taking this to the dealer if their own service manual and diagnosis is going to have the same results as my testing.
Where do I go from here?
Could PVHS be causing a code from the manual hubs?
Could the MSS be causing a code even if it is showing correct in AE?
Should I try a new TCSM? Should I try turning the TCSM manually? How do I test, what do I test for on the TCSM?
Using the Ford IDS ? My VCM 1 will not communicate with the PCM. The #3 light on the VCM stays solid red. I am running IDS 75.00. I don't have another truck to try it on. Bad cable from obdp to the VCM ?
View 14 RepliesMy airbag light is on and I don't have a clue what to look for. Recently had body off, but I've checked all my plugs and all looks good. No codes relating to airbag in the memory.
What's the airbag checklist?
I replaced my fan clutch... Not a bad job, did it a couple weeks ago. I don't drive the truck much, but took it out today for the second time in the two weeks since I replaced it. The fan stays engaged until the truck hit operating temperature it seems. Is that normal?
View 1 RepliesOk so here is my problem now. I'm sure its in the tramny but not sure what else. My shift from 3-5 has always been a little hard. Yesterday on my way to work I noticed shifts 1 thru 3 were hitting hard. Once I got up to 65 mph it was okay. Then pulling into work when I shifted to reverse it didn't go into gear right away and then it would hit into gear. Later that evening on my way home from work it was shifting the same but seemed worse. Then my tow/haul light started flashing and it seemed like the torque convertor wouldn't lock in. It would just stay in 5th gear and the more throttle I gave it the rpms would go up but I would only get a little response from it. Then a few miles down the road it just completely shut off on me. It will not even try to turn over. I could also hear a noise coming from underneath the truck. Something ive never heard before. I really need to figure this out
View 14 RepliesCame on other day. No ses light or fault codes. What it means?
View 10 Repliesmy 2003 f-250 4x4 6.0 engine service light stays on all the time (for about 2 weeks now) it has 33,323 miles on it. it is running fine-no problems yet. no codes are showing up on a diagnostic test. What is going on?
View 10 RepliesSo I picked up a 53' for the racecar. When I'm hauling it on take off I'm getting a pretty good shutter out of the truck. My crew chief who owns a maintenance shop, said it's a known issue, and ford has been shimming the drive shafts.
I talked to the service writer at my dealership and he said it's a known issue and they are working on it. However, he said if they shim the driveshaft, there is a good chance it could fix the problem loaded, but then unloaded I'd have the problem. Is there a setup that's recommended?
I'm towing about 15k, but that's far from the limit of my 450.
Finished my install last night for my airbags. The passenger side looks good as far as alignment top to bottom, but the drivers side is tilted pretty good. I lined up the alignment pin in the upper mount as the instructions indicated into the most forward hole and there is no way to move the lower mount because it is up against the leaf pack tight where it belongs and the tabs on the lower mount does not allow for it to be turned on the axle housing. I believe it is out of alignment enough to cause excessive wear and or improper performance (the rubber part of the airbag is actually touching the lower metal disc that is part of the airbag when there is no air in it).
View 14 Replies2011 F250 Fx4 diesel. I'm pulling a 14' GN dump trailer. My truck squats. Should I go to ford and get a quote to put the overload package on or put in an airbag system? I want to put a on-board air compressor in for air chuck use and louder horn.
View 14 RepliesTruck = 2011 F250 150,000 miles, no modifications, stock.
Truck lost power yesterday, no boost, and no codes. When driving on Friday, I started moving from a red light. The truck seemed very sluggish. Then I noticed it downshift going up a small hill that it never downshifts before. I looked, and noticed the turbo gauge at 0, no boost. I pulled over, turned it off, then restarted it, but still no boost, and the truck is very under-powered. I looked over the area, and do not notice any leaks, also no leaks underneath. I hooked up my OBD reader, and no codes., the boost gauge is on zero, and the truck has lost significant power. I no longer hear the turbo spooling.
I have spent the past several hours searching sites and forums (Started with FTE ), and it seems that most believe a restart of the truck has solved it for them. However, this is not the case for me, a restart, even after letting it sit overnight did not resolve the issue.
I did see one reference that replacing a NOX sensor solved their problem. This brings up some interesting truck history. Back in June 2017, my truck threw the following codes, P207F and P20EE.
P207F - Reductant Quality Performance
P20EE - SCR NOx Catalyst Efficiency Below Threshold (Bank 1)
The message said I have 200 miles until reduced power. Since it was a Friday, not much I could do at the time so I let it sit overnight, and then the next morning the message was gone. I plugged in the OBD reader and cleared the only remaining code (P20EE), and its been a very happy truck until yesterday.
So my question, can a bad NOX sensor cause the issue of loss of turbo boost, with no codes? Is there another possible cause?
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
OK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 RepliesSo I was driving down highway when I lost power. Engine was still running just had no power and would blow black smoke when I got on the accelerator. I pulled the EGR valve and noticed it had rocks stuck keeping the valve open. Cleaned it all up and put it back in. Went for test drive and seemed good again until few miles in same problem. Took it apart again and same thing.. rocks. I did this 3 times with same results...rocks getting stuck in my valve.
View 1 RepliesI have a 06 f250 king ranch with 6.0 . A few days ago my scangauge showed a code P0405
I changed my egr and after it showed two codes : P0405 and P0404
It still has a hesitation and loss of power , although better than before the Change.
Alright so I'm a little frustrated at my truck for the last month. I have a 2013 f350 with 2 codes comming up. P0100-mass or volume air flow circuit and a U0106-lost communication with glow plug control module. I have an H&S tuner with the delete. I changed the MAS and it's still lighting up. The dealer is looking into it cause they didn't foresee any problems with the glow plugs either. I erase the code, shut the truck off and once I start it it's right back on! Frustrating!
View 14 Replies