Is it possible to add the decent control if my truck didn't come with it? Is the harness already wired for it and the computer programmed for it or would I have to get it reprogrammed and get a new harness?
View 6 RepliesI have 2 messages showing up in the message center / control panel. I have taken the truck to the dealership and we cannot recreate them while the truck is at the dealership. How it can be resolved.
2013 Ford Superduty Platinum : 33,800 miles and the truck is stock
Messages : service traction control / Downhill decent control fault
This will happen just driving down the road or just after starting the truck and taking off.
It has happened towing my work trailer and also not having the trailer connected to the truck.
As it turns out my entire dash needs to come out to repair the HVAC so thinking while it's out I should add the diesel supplemental heater. What's involved with this? I need to replace the entire HVAC plenum so imagine the version with the supplemental heater can be bought instead. I know it's an 1800W electrical heater so my main question is the wiring harness on a regular truck setup for it or do I need to change the harness. And then I suspect the HVAC control module would need to be reprogrammed as well.
View 13 RepliesI am going to add some led's to illuminate the steps getting into my truck at night. I plan on putting them directly under the door over the steps. Is there a wire under the door threshold I can tap into at each door? If so what color? If not, where to get the power from. I want them to turn on and off with the interior lights when doors are opened.
View 1 Replies2007 F550 with the 6.0. About 2 months ago I replaced the EGR cooler with a Bulletproof cooler. Truck ran well for a few weeks. Then I started getting the "turbo fart". I stopped using the truck until I had an issue with another truck. I was stuck so I sent the 07 out without cleaning the turbo. This morning a decent amount of white smoke started coming out of the exhaust. The smoke would sometimes get a bit gray. Going up hill it didn't have much power at all.
View 8 RepliesIs there a difference between the two harness #'s here besides the first number:
3C3z9d930aa
4C3z9d930aa
Are they the same part? Is one for a different model truck than the other?
Need to know the Ford part number for cab light wiring harness? I am wanting to install some LED cab lights but I do not currently have any so I will need the wiring harness.
View 3 RepliesWill a 05 injector harness work on a early 04?
View 1 RepliesHave a 2010 Lariat crew cab and I just bought an upfitter switch set and relay harness. Found where to mount the relay block and have been able to get the switch panel installed in its home. For the life of me though I cannot find the plug in the main harnes under the dash to plug the relay harness into to power everything up. I've read several threads here and even found the drawings that indicate plug #C215 in a diagram for the 2011+ trucks. When I get access panel out and look underneath the dash where it should be....no spare or open plug. Is the plug location diferent in 2010 from the 2011?
View 2 RepliesCould a leaking passenger side glow plug harness cause a "hot no start?
View 5 RepliesI'm really struggling to get this sucker off my 2014 6.7 F350
it says in the ford manual to lift the plastic tabs then pull off, I did that easily with 3 on each side, but the end plug on each side (the one closest to the windshield) does not seem to have a liftable tab (it looks different to the others as its at the end of the cable)
I've almost broken it but not quite, its over $300 for new harness, ouch
I do have the odd little hook tool they sell for this, it worked with the other 3 for sure, but I've spent ages on the 4th on each side and cannot budge either of them
First I lost the power window functionality in the rear left door... didn't think too much of it, then I lost the power door lock functionality, which was bad because I was assuming my door was getting locked when it wasn't actually. Pulled open my door this evening and found this:
I think my truck overheard me when I was saying "I like a good electrical problem, those are my favorite." I'll solder it up to get it working tonight, and then I'll see what a new harness costs... although really they should have used ultra-fine-strand wire with silicone insulation for an application that sees lots of flexing.
My multimeter's test leads are such an example of wiring that is intended to see lots of flexing.
Got a 2003 6.0 that seems to be leaking from the glow plug harness. How hard would it be to just replace them? I've heard that trying to remove these things can be a pain because they almost always break. But if I'm just going to replace them who cares right?
Is there anything I need to be careful about? Or can I just rip em on out? Also I've noticed two different styles of harness should I replace mine with the other style or just keep it the same? And yes those valve cover nuts are loose. I'm aware
Looking for an electrical schematic and or wiring diagram of the windshield wiper circuit for a 06' Super Duty?
View 5 RepliesI need to connect a remote start stop for a bucket truck attachment to this new 2016 F550. Found everything except the ignition wiring harness diagram. Need to know what I can tie in to.
View 4 RepliesReplace the tft but still the problem, someone cones the number part of tft sensor harness, and as replace , 2006 f350 4x4....
View 2 RepliesWe just picked up a 2007 f350 dully with 71,000 miles on it. Have done some research but still would love some input. We would like to do the egr delete and add a monitor/programmer to monitor things. We will be using this as a daily driver and to haul our dj equipment trailer (nothing big) have looked at several programmers and also talked with several local diesel owners currently leaning toward the Edge Cts2.
View 9 RepliesI came across a post where someone said it was possible to add a gauge/setting to the blank "gauge display" screen. I've searched and searched but can't find the post. Ho to add to the gauge display blank screen.
View 14 RepliesIs there a MPG gain with synthetic oil or adding a tonneau cover?
I'm planning on doing the tonneau but curious if any noticeable differences with either.
I first saw them on the 2013 build and price and was thinking that I should look into adding them to my 12. I never got around to looking up part numbers. So, recently I thought of it again and after a little poking found that they could be had as a Ford accessory kit for around $110 depending on your dealer. MSRP is 133 I think. So, I hit the dealer and grabbed a set they had in stock. Install took 30 minutes. Very easy. They give the wheel wells a finished look and offer lots more protection than the small plastic strips on the rear that came with the truck. A hundred or so bucks well spent if you don't have them. There are aftermarket ones that are a touch cheaper on eBay by Rugged Liner but they don't work with the 5th wheel prep which I have.
View 14 RepliesMy fathers truck had the tail lights go out the other night so we checked the fuse and the bulbs both good. Took it to ford and they found that a wire harness in the front left wheel well had rubbed through and needed replacement. I went and checked mine and yup it was rubbing through the wire just not all the way yet. Might want to take a look. It is at the top of the well near the coil spring. I will get the camera out tomorrow in the daylight and take a picture of the location.
View 13 Replies