I didn't have time to trouble shoot but heres my problem. I plugged my 2016 6.7L in last night and when I checked it this morning the block was still ice cold. I didn't have time to investigate but i did make sure i had power up to the truck. And i noticed there's a connector just after the truck plug as well.
View 14 RepliesWell, I swapped a 2011 F250 SC for an F350 CC and I really enjoy driving it. 300 miles on the clock. My old 250 had the block heater and the pigtail to plug it in was low in front of the radiator. This truck also has the block heater, but I cannot find the pigtail to plug it in. In 2016 where Ford hid it at?
View 14 RepliesI don't think that my block heater is working correctly if not at all.
View 14 RepliesDoes the block heater come with some kind of a cord? I found the Box Link stuff under the back seat finally, the dealer said the block heater should be under there too? But it aint there?
View 6 RepliesI can't get my truck to start. The block heater isn't working and I previously put flush and water in it, intending to drive it and flush it directly after. Well I never really could drive it and now it won't start again. The weather is going to turn off cold, around zero this weekend. I need to know how to keep the block from freezing and cracking!
View 11 RepliesDon't drive the truck but once a week but since its gotten colder here than usual is been harder to start when cold. Of-course I go thru the glow plug wait and then it kinda stumbles when its about to start. I do it again and most of the time is starts but seems rough for a few seconds. Once the truck is warm, no more problems starting.
I'm wondering if I have a glow plug gone bad and that cylinder is not warming up for me. Today I plugged in the block heater for maybe 2 hours and it started first time. Also, if just leave the block heater plugged in for long periods of time.. would it get to hot?? and wonder how expensive that is, most heater are costly to run. I have a timer but just wondering.
Ok, is it possible to blow a fuze if the block heater is still plugged in when starting? Almost did this the other day and wondered if its possible to cause a short or something.
View 6 RepliesWhat the coolant temp should be around after plugging in the block heater overnight? Not looking for an exact measurement since this can be affected by OAT and the length of time it has been plugged in. But when it's -15 to -20F this weekend I was wondering what to expect.
View 13 RepliesWas driving today and noticed that at idle my heated air went away. Coolant temp at this point was 185f. Once back to driving, the heat returned. The variant in temperature seems to be related directly to engine speed. What is wrong?
View 7 RepliesI have tried the dealership 3 times and have not been able to get the rear heater to work properly. When the vehicle is moving I have heat but if I slow or stop the heat goes away. I believe it only happens to the rear heater as front feels fine.
View 4 Replies I wanted to specifically ask about the block heater though. Since I bought this truck I never was able to start the truck without plugging it in. Now that it's not running I'm thinking much more about the block heater.
Is 56 too low for this old truck to start? What temp should a block heater have the oil temp as seen by AE be?
I live in the southwest so it's not very cold here. plugging in the heater was even required in the summer unless the truck had been running. What kinds of engine trouble would require being plugged in in warm conditions?
Doing oil cooler. Block heater plug is very tight. Is it reversed threaten?
View 1 RepliesWhen the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
my egr delete j pipe orings give me trouble and i replaced but broke a bolt, now i think that big donut oring is leaking, i was reading you can put a 3/4 freeze plug in to eliminate any coolant into the intake, where does the freeze plug go,front cover or intake and does coolant still pass thru the j pipe?
View 7 RepliesSeen a coolant leak near the back of the block? I did an oil change and noticed coolant on the bell housing.
View 7 RepliesHas actually removed the block plug (from where ever it is) and installed a heating rod...I'm fairly mechanical, just not sure of the steps or tools needed.
View 14 RepliesHow can I tell if the engine block heater in my 2010 Prius is working (dealer installed)? The one on my old Subaru made a hissing noise; the one on the Prius makes no noise.
View 19 RepliesI am doing heads studs and gaskets on the truck. I forgot to remove the stand pipe and started to lift the head off the truck with the engine jack. Well i bent the stand pipe and the port to the bock was a little loose. Tightened it back down and it seems ok. Could I have damaged anything by doing that? how is that all connected to the high pressure oil pump? I just want to make sure i didnt damage anything by doing that and since im already here I would rather make a fix instead of needed to tear down again.
View 5 RepliesWhen I bought my truck it didn't have the block heater installed, asked the dealership to put it on with the deal, but they didn't have one there. How hard it is to install one? Also what brand should I go with? (On my '16)
View 5 RepliesIt got down to the low teens the other day and I thought I would use my engine block heater to see how well it works. But when I got in the oil temp was basically the same as the air temp (it may have been 5-10 degrees warmer but still not above 20*F) after being plugged in for 2-3 hours. Is something wrong here? I would have thought it would have warmed it up or does it not affect the oil temp? If not, what does it warm up?
View 7 RepliesCold no start goes nowhere. I have a 2001 7.3 that will not start in the cold if I forget to plug it in....like last night. I have to plug in the block hater and give it a while before it will start. I tested the glow plug relay,it works fine. I can not find a test for the fuel bowl hear, and I'm not one to throw parts until I accidentally fix it. Any test procedure for the fuel bowl heater? Why this POS is so bad in the cold? Glow plugs tested fine at diesel shop in December, and this problem has been around since before that.
View 14 Replies