Just bought a 13 6.7 used. It is in excellent shape but, you turn the key off and it is a few seconds before it dies? Is this maybe something aftermarket the previous owner installed?
View 8 RepliesGot up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
I have a problem with my F250. The engine is turning, rail pressure 400kpa, but it does not jump at. Injectors are tested at bosch. High and Low Fuel Pressure Pump are new.Sensors and pressure regulator also. Compression is also ok on all cylinders.
View 4 RepliesI bought a 99F350 with a 7.3, it was not running when I bought it. Batteries good, new starter, turns over just fine, fuel pump works, but now I don't know what to look for.
Was testing ohms for my injectors and at the plug on top of the driver side valve cover, couldn't get a reading at all, tested the ohms at the pass. Side valve cover plug and got good ohm readings.
So loss power on take off and then stopped at store quick shut it down. Came out of store ten minutes later no start just turns over and over. I replaced IPR last year the one on passenger side near frame if that's correct and perhaps this is the ICP near back of engine?
View 14 RepliesI'm new to the Ford 6.0 diesel motor just got one from someone and the fusses and relays have been messed with. I have fuel up to the second fuel pump and it sounds like it's working but It just turns over. I purchased the Haynes manual but it doesn't have information on how to test the injectors or fuss box set up.
View 8 RepliesAs the title says I'm driving down the road and the radio just turns itself off, If i hit the power it turns on but it's like a ghost hit turned it off.
View 4 RepliesWhen I start my truck up and leave the parking lot from work I have to take several turns. When I do this it feels like there is no fuel getting to the engine and the truck acts like it is going to stop. I assumed it was some kind of fuel issue and thought it would clear itself up over time. I have had the issue with my truck for several months now...
View 4 RepliesWtf is going on, Temps are all good, no check engine codes...bad diesel fuel? I had 1/4 tank of diesel fuel when I filled it up...
View 14 RepliesI changed out my fuel filters today on my 2016 F350 SD and right parts, no leakes, main filter full, and I did the 6 cycle fuel pump prime. Turns over but won't Start. Redid the 6 cycle prime several times now and still no start. Pulled the 2ndary filter lines while it was priming to see if flowing and got squirted on both lines.
View 8 RepliesTurns over great but nothing. just changed fuel filters all voltages read great. I have ScanGuage and what little I can tell everything reads good. Has been acting funny for a couple weeks taking 4 or 5 cranking attempts to start every now and then no real pattern. Runs great when going even when pulling a load. It has failed to start and I'm in my shop and not sitting on the side of the road.
View 6 RepliesI have an 03 f250 that i think is getting air in the fuel line when it sits. It turns over starts and immediately shuts off. Then i have to crank it for a minute or so before it will start. After that it is good all day. Next day it might sputter on start but stays on. More than a day it shuts off immediately and needs cranking for a minute...
View 13 RepliesI "Bulletproofed" my f-250 Super-duty last summer and she ran great for a time, actually she is still running great, except for one thing that is driving me crazy. On a cold start it turns over until the oil pressure builds up. Then she will crank and runs fine, also starts normally after warm, turns over a couple of times and cranks.
I have oil in the filter housing, have replaced the seal at the bottom of it. Just pulled the oil rails off and replaced the seals on them, and a new IPR seal and filter. I am still having the problem, F.I.C.M. voltage has been fluctuating between 45 and 46 vdc. I have a P300 and P308 code.
I haven't really considered Injectors because it is idling smooth as silk and has great power.
My 6.0 with 178k on it just started to have issues today. Low power. When I hit the pedal hard the motor revs and the truck barley moves. When I baby it it goes up to speed and shifts fine. Overall lacking power and not going anywhere. No CEL on. Turbo spools and seems to be ok.
View 5 RepliesFirst post since I bought my powerstroke. I was looking for some diagnostics.
On my way to work this morning and the truck started chugging like it was wanting to die and had no power, the pedal was to the floor and I was barely moving. I was able to nurse it to a parking space at work and pulled the codes, using the Torque pro. This was what I pulled:
P0284 - Cylinder #8 contribution/balance
P0299 - Underboost
P0611 - FICM
P0401 - EGR
P0671 - Cylinder 1 glow plug
On the way home I didn't even hit 5 miles and started into the same symptoms. So I decided to call for a tow, because my commute is about 60 miles one way. In waiting for the tow truck I disconnected the batteries and reconnected them thinking that it might "reset" something. I started it up and the same thing occurred, so I tried revving it up, and starting it up and shutting it down on and off for about an hour. Thinking I picked up some bad fuel. Drove it for a short distance and found things were getting better. I was able to make it home and pulled the codes again. It came up with these:
P0284
P0603 - Internal Control Mod.
P0611
P1000
Also on the ride home I had excessive amounts of black smoke from the exhaust and found a couple of large drops of oil on the driveway where i normally park, larger than what I normally see.
So my question would be what is the cause of all of this?
A little about the truck. it is a F250 CCSB with about 139xxx miles on the clock. I bought it from my brother when he had it he had the FICM replaced (with the 58V option) and the Bullet proof EGR installed. I replaced the fuel spring with the blue one shortly after I bought it.
I removed all 8 injectors because my truck felt like it had a dead cylinder one morning after I did oil change and filter and fuel filters. Truck ran great the day of the fluid change. The next morning however truck was hard to start no power at all nothing. Felt like a dead cylinder so removed all 8 injectors and ohm them all ohm at 0.4 to 0.5 except number 4 injector it ohm at 0.4 and 0.7 that's not in spec right or am I wrong? Do I need a new solenoid? Keep in mind tho number 5 and 8 injectors had contribution codes but they ohm good. So I'm going to tear the injectors apart and see what's what. But my question is do I need to replace number 4 injector solenoid?
View 3 RepliesI just pulled over when my truck flashed reduced power. Pulled code and it came up poo88. What to expect?
View 3 RepliesOK getting these 2 codes PO113 and PO4DA What now have 17,000 miles and a long weekend. Truck has no power barley moves. Can't get it to a dealer till tuesday.
View 1 Replies2015 F350 6.7L, 43,000miles
My family and I were driving into West Virginia this morning when the reduced engine power message came up on the dash and the truck died. I coasted off to the side of the road as best I could and got out. Immediately I smell diesel fuel. I look under the truck and there is fuel all over the passengers side frame and when I keyed it back up fuel started spraying down by the right front wheel.
Pulled the fender liner back and saw a small rubber hose that looks like it came off of a tee fitting down by the egr components. I tried to get it back on but wasn't able to get it seated 100% and when I tried to restart it blew off again. Truck is completely stock and ran perfect right up until it died.
2011 6.7 with 3.55 gearing. Just got the truck. And it seems when its cold the truck will rev high in 3rd gear and then sort of fall into 4th gear sort of losing power for a split second. If I gas it hard, its not as bad. Usually only happens like I said when its cold. Check the trans fluid its full and looks clean. My guess is some sort of sensor or the computer???
View 7 RepliesIt's a 2004 6.0 excursion with about 190,000 miles. At 185,000 I pulled the motor and did new oem head gaskets, Arp head studs, bulletproof egr cooler and oil cooler system, bulletproof 48v ficm, strictly diesel regulated return, and I've been running gear heads srl tune before and after the truck was rebuilt.
Recently the truck has been acting up at random times. While running the gear head srl tune, the truck will lose power, the boost gauge on my edge insight will get stuck along with Icp psi, the water in fuel light and glow plug light will come on, and then after a few seconds it will clear itself and run fine. Last night I was on a two lane road and putting my foot into it and the truck did the same thing where it loses power, but this time the truck actually died on me while I was cruising at 60.
Same lights were on but this time the cruise control light fluttered while the truck was in the midst of dying. I tried restarting it and it took two sets of cranking before it fired and stayed running. On the way home I babied it and the truck lost power and the Rpms dropped and only the glow plug light came on. Got home and ran codes and I got camshaft and crankshaft position sensor codes and I tuned it back to stock, drove it around, and the truck ran fine, but while on a stock tune I am getting a egr valve code.